• Korean Chemical Engineering Research
• /
• v.44 no.2
• /
• pp.179-186
• /
• 2006

Two types of $TiO_2$, nanotube and nanoparticle, were used for the mesoporous coatings by doctor blade technique followed by calcining at $450^{\circ}C$. The coatings were used as working materials for dye-sensitized solar cells (DSCs) later on and their photovoltaic characterization was carried out. The nanoparticle was synthesized from hydrogen titanate nanotube by hydrothermal treatment at $180^{\circ}C$ for 24 hr. The solar energy conversion efficiency (${\eta}$) of DSCs prepared by this nanoparticle reached 8.07％ with $V_{OC}$ (open-circuit potential) of 0.81 V, $I_{SC}$ (short-circuit current) of $18.29mV/cm^2$, and FF (fill factor) of 66.95％, respectively. For the preparation of nanotube, the concentration of NaOH solution varied from 3 M to 5 M. In the case of DSCs fabricated with nanotubes from 3 M NaOH solution, the ${\eta}$ reached 6.19％ with $V_{OC}$ of 0.77 V, $I_{SC}$ of $12.41mV/cm^2$, and FF of 64.49％, respectively. On the other hand, in the case of 5 M solution, the photovoltaic ${\eta}$ was decreased with 4.09％ due to a loss of photocarriers. In conclusion, it is demonstrated that the solar energy conversion efficiency of DSCs made from $TiO_2$ nanoparticle showed best results among those under investigation.

• Clinical and Experimental Reproductive Medicine
• /
• v.4 no.1
• /
• pp.17-25
• /
• 1977

Anderson(1937), Power and Barnes(1941) reported a study concerning a method of tubal sterilization in association with peritoneoscopy or laparoscopy in which they cauterized the tubes. There appears to have been a hiatus of interest in sterilization (cold or hot) associated with laparoscopy until reintroduction by Palmer(1963), Frangenheim(1964) and Steptoe(1967). On the other hand, for interval female sterilization, however, minilaparotomy is relatively new. By Saunder and Munsick(1972), John Lyle(1974), Frank Stubb(1974), Vitoon(1973) and B.C. Bai(1975), their own technique for interval female sterilization requires 2.0 to 2.5cm, incision at the margin of the mons pubis. In Korea, female sterilization by means of minilaparotomy firstly reported by B.C. Bai using Bai's uterine elevator, of his own device, early in 1975. Recently inteval female sterilization by laparoscopy and minilaparotomy are widely accepted throughout the world especially in Asian countries. Minilaparotomy is carried out from 1974, laparoscopic sterilization from 1976, and in this study each of 250 cases of those were analysed and discussed for the comparison at Seoul Red Cross Hospital. (1) In the age distribution, numerous clients were in their age of $31{\sim}35$ in laparoscopy as well as minilaparotomy. Average 33.7 years in L and 33.2 years in M. (M=minilaparotomy, L=laparoscopic sterilization) (2) As regarding living children, women having 3 children represented the greatest number, 113 cases out of 250 in M group and 102 cases out of 250 in L group. Average No. of child are 2.9 in Land 3.1 in M. (3) Concidering the operation day in the menstrml cycle, the greatest number of cases, those who underwent tubal sterilization during the days of $26{\sim}$, next during the $6{\sim}10$ days of the cycle in both group. (4) Concidering the operation time, 188 cases by laparoscopy were performed in $6{\sim}10$ minutes, 33 cases within 5 minutes and 24 cases in $11{\sim}15$ minutes. Maximum 50 minutes, minimum 4 minutes and average 8.3 minutes. The majority of cases (154 cases) by minilaparotomy required $6{\sim}10$ minutes and 67 cases $11{\sim}15$ minutes, 6 cases within 5 minutes. Maximum 30 minutes, minimum 4 minutes and average 10.4, minutes. In both groups, most of the reasons for the extra length were surgical difficulties such as thick abdominal wall, pelvic adhesion, less cooperation of patients in early period of this study. (5) Hospital stay after operation in L group required $3{\sim}4$ hours in 125 cases, $2{\sim}3$ hours in 41 cases, $4{\sim}5$ hours in 32 cases out of 250. Maximum 8 hours, minimum 1 hour and average 3.8 hours. In M group hospital stay required $6{\sim}7$ hours in 100 cases, over 7 hours in 85 cases, $5{\sim}6$ hours in 46 cases and so on. Maximum 14 hours, minimum 2 hours and average 6.5 hours. (6) The time between operation and gas passing in the majority cases of both groups, were $12{\sim}36$ hours. A veragetime 20.3 hours in L and 27.2 in M. (7) Laparoscopic sterilization coincident with induced abortion were carried out in 27 cases, laparoscopy with minilaparotomy to control for mesosalpingeal hemorrhage in 1 case. Minilaparotomy coincident with induced abortion were performed in 65 cases, D and C whit polypectomy, menstrual regulatian, and remaval of IUD in 1 case respectively. (8) In L group, 1 case of mesosalpingeal hemorrhage, 1 case of abdominal wall infection were complicated during operation. In M group, 1 case of uterine perfaration, 1 case of abdominal wall infection, 1 case of hemorrhage from omentum and 1 case of bloody vaginal discharge were complicated. No intensive medical treatment was required for those minor complications in both groups. (9) No failure has been recognized and these two sterilization techniques might be the simple, safe and the most effective method for permanent contraception at present time. There is no significant clinical defference between L and M group in this study.

• Archives of design research
• /
• v.18 no.3 s.61
• /
• pp.85-94
• /
• 2005

Most of product designers use 3D CAD system as a inevitable design tool nowadays and many new products are developed through a concurrent engineering process. However, it is very difficult for novice designers to get the sense of reality from modeling objects shown in the computer screens. Such a intangibility problem comes from the lack of haptic interactions and contextual information about the real space because designers tend to do 3D modeling works only in a virtual space of 3D CAD system. To address this problem, this research investigate the possibility of a interactive quantified structure simulation for product design using AR(augmented reality) which can register a 3D CAD modeling object on the real space. We built a quantified structure simulation system based on AR and conducted a series of experiments to measure how accurately human perceive and adjust the size of virtual objects under varied experimental conditions in the AR environment. The experiment participants adjusted a virtual cube to a reference real cube within 1.3% relative error(5.3% relative StDev). The results gave the strong evidence that the participants can perceive the size of a virtual object very accurately. Furthermore, we found that it is easier to perceive the size of a virtual object in the condition of presenting plenty of real reference objects than few reference objects, and using LCD panel than HMD. We tried to apply the simulation system to identify preference characteristics for the appearance design of a home-service robot as a case study which explores the potential application of the system. There were significant variances in participants' preferred characteristics about robot appearance and that was supposed to come from the lack of typicality of robot image. Then, several characteristic groups were segmented by duster analysis. On the other hand, it was interesting finding that participants have significantly different preference characteristics between robot with arm and armless robot and there was a very strong correlation between the height of robot and arm length as a human body.

• Journal of Life Science
• /
• v.17 no.5 s.85
• /
• pp.634-640
• /
• 2007

Our previous study suggested that n-3 fatty acid deficiency was associated with significantly reduced spatial learning as assessed by Morris water maze test. Here we investigated an effect of n-3 fatty acid deficiency on rat brain, retina and serum fatty acyl compositions at 15 wks age using a first generational artificial rearing technique. Newborn Rat pups were separated on day 2 and assigned to two artificial rearing groups or a dam-reared control group. Pups were hand fed artificial milk via custom-designed nursing bottles containing either 0.02%(n-3 Deficient) or 3.1% (n-3 Adequate) of total fatty acids as a-linolenic acid(LNA). At day 21, rats were weaned to either n-3 deficient or n-3 adequate pelleted diets and fatty acid compositions of brain, retina and liver were analyzed at 15 wks age. Brain docosahexaenoic acid(DHA) was lower(58% and 61%, P<0.05) in n-3 deficient in comparison to n-3 adequate and dam-reared groups, receptively, while brain docosapentaenoic acid(DPAn-6) was increased in the n-3 deficient group. In retina and serum fatty acid compositions, the decreased precentage of DHA and increased precentage of DPAn-6 were observed. These results suggested that artificial rearing method can be used to produce n-3 fatty acid deficiency in the first generation and that adequate brain DHA levels are required for optimal brain function.

• Asia pacific journal of information systems
• /
• v.23 no.4
• /
• pp.103-128
• /
• 2013

When a consumer needs a product or service and multiple sellers are available online, the process of selecting a seller to buy online from is complex since the process involves many behavioral dimensions that have to be taken into account. As a part of this selection process, consumers may set minimum trust expectation that can be used to screen out less trustworthy sellers. In the previous research, the level of consumers' trust expectation has been anchored on two important factors: product involvement and perceived risk. Product involvement refers to the extent to which a consumer perceives a specific product important. Thus, the higher product involvement may result in the higher trust expectation in sellers. On the other hand, other related studies found that when consumers perceived a higher level of risk (e.g., credit card fraud risk), they set higher trust expectation as well. While abundant research exists addressing the relationship between product involvement and perceived risk, little attention has been paid to the integrative view of the link between the two constructs and their impacts on the trust expectation. The present paper is a step toward filling this research gap. The purpose of this paper is to understand the process by which a consumer chooses an online merchant by examining the relationships among product involvement, perceived risk, trust expectation, and intention to buy from an e-tailer. We specifically focus on the mediating role of perceived risk in the relationships between enduring product involvement and the trust expectation. That is, we question whether product involvement affects the trust expectation directly without mediation or indirectly mediated by perceived risk. The research model with four hypotheses was initially tested using data gathered from 635 respondents through an online survey method. The structural equation modeling technique with partial least square was used to validate the instrument and the proposed model. The results showed that three out of the four hypotheses formulated were supported. First, we found that the intention to buy from a digital storefront is positively and significantly influenced by the trust expectation, providing support for H4 (trust expectation ${\rightarrow}$ purchase intention). Second, perceived risk was found to be a strong predictor of trust expectation, supporting H2 as well (perceived risk ${\rightarrow}$ trust expectation). Third, we did not find any evidence of direct influence of product involvement, which caused H3 to be rejected (product involvement ${\rightarrow}$ trust expectation). Finally, we found significant positive relationship between product involvement and perceived risk (H1: product involvement ${\rightarrow}$ perceived risk), which suggests that the possibility of complete mediation of perceived risk in the relationship between enduring product involvement and the trust expectation. As a result, we conducted an additional test for the mediation effect by comparing the original model with the revised model without the mediator variable of perceived risk. Indeed, we found that there exists a strong influence of product involvement on the trust expectation (by intentionally eliminating the variable of perceived risk) that was suppressed (i.e., mediated) by the perceived risk in the original model. The Sobel test statistically confirmed the complete mediation effect. Results of this study offer the following key findings. First, enduring product involvement is positively related to perceived risk, implying that the higher a consumer is enduringly involved with a given product, the greater risk he or she is likely to perceive with regards to the online purchase of the product. Second, perceived risk is positively related to trust expectation. A consumer with great risk perceptions concerning the online purchase is likely to buy from a highly trustworthy online merchant, thereby mitigating potential risks. Finally, product involvement was found to have no direct influence on trust expectation, but the relationship between the two constructs was indirect and mediated by the perceived risk. This is perhaps an important theoretical integration of two separate streams of literature on product involvement and perceived risk. The present research also provides useful implications for practitioners as well as academicians. First, one implication for practicing managers in online retail stores is that they should invest in reducing the perceived risk of consumers in order to lower down the trust expectation and thus increasing the consumer's intention to purchase products or services. Second, an academic implication is that perceived risk mediates the relationship between enduring product involvement and trust expectation. Further research is needed to elaborate the theoretical relationships among the constructs under consideration.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.30 no.3
• /
• pp.42-56
• /
• 2012

This study was carried out to investigate the construction characteristics and the landscaping design skill for Wiyiam at Ongnyucheon(玉流川) in the rear garden of Changdeok Palace focusing on constructing technique, space composition and transformational process of the site. The results of this study were summarized as follows; First, Wiyiam of Ongnyucheon was constructed as garden ornament which was modified the huge bedrock into the shape of the mountain. The waterfall of Wiyiam was originally made of torrent which water flowed into the bottom, but it was reconstructed to take the effect of Inak(離落: the method to drop water from high place) by carving rock into square shape at the era of King Gojong(高宗). Second, main characteristics of Wiyiam appeared in Donggwoldo was the hill built up with a square pond and ground at the back of Wiyiam and the profound scenery of mountains and stream from the view of Wiyiam. Also, pavilions such as Soyojeong(逍遙亭), Cheongujeong and Taegeukjeong(太極亭) built in Ongnyucheon seemed to be constructed as the spots to appreciate the view and waterfall sound of Wiyiam. Also the spots were not bounded by the function of creating special water systems such as Cheongujeong pond and Taegeukjeong pond and showed the outstanding landscape design skill to make people feel unusual interest from each spot. On the other hand, this study considered that the evening scenery of Wiyiam, beautiful sound of falling water, unusual water system with beautiful plant materials were landscaped for the function of the psychological peace and stability to the appreciators. Lastly, the extreme change of space composition in Ongnyucheon was assumed as a strategy to improve the existing poor drain environment by confirming that the mountain stream and wall of Soyojeong were removed and drainage in both side of Soyojeong was installed in the 21th year of King Gojong's reign(1884).

• Journal of the Korean Association of Geographic Information Studies
• /
• v.12 no.4
• /
• pp.34-47
• /
• 2009

Rapid urbanization is causing environmental and ecological damage, development thoughtless for the environment, and social and economical issues. It is important to grasp urban growth situations and characteristics, reflect them, and establish a policy for the solution of issues pursuant to urbanization and the sustainable and efficient development of national land. This research aims to be used as basic data in establishing an urban policy by analyzing the situations and characteristics of urban growth for the past 20 years in our entire country rather than an existing district. For this, some urban districts were sampled using a 1980s and 2000s version of land cover map produced by Ministry of Environment, and then pattern analysis for urban growth by administrative district ranks was conducted using GIS and a statistical technique. As a result, the development zone area after 1980s has increased by 2.5 times as compared to that before 1980s, and especially in the farm villages neighboring the national capital region, it has increased by 21.2 times. Special cities and metropolitan cities were developed at the districts being low in altitude, close to the principal road and the major downtown, high in road ratio, and restricted environmentally, ecologically and legally, and were diverted from mountains, forests and grassland to urban land. On the other hand, farm villages neighboring a large city, farm villages neighboring the national capital region, and local farm villages were developed at the districts being high in altitude, far from the principal road and the major downtown, low in road ratio, and not restricted environmentally, ecologically and legally, and were diverted from farmland to urban land. That is, it can be seen that urban development has been actively realized despite the unfavorable topographical conditions in the suburban districts due to lack of available land and various regulations and policies as urban growth around big cities expands.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.16 no.4
• /
• pp.115-133
• /
• 2021

This study examines the concept and related technologies of the 4th industrial revolution that has been mixed so far and examines the socio-economic changes and influences resulting from it, and the cases of responding to the 4th industrial revolution in major countries. Based on this, by deriving SWOT factors and calculating the importance of each factor for Korean venture companies to prepare for the forth industrial revolution, it was intended to help the government and policymakers in suggesting directions for establishing related policies. Furthermore, the purpose of this study was to suggest a direction for securing global competitiveness to Korean venture entrepreneurs and to help with basic and systematic analysis for further academic in-depth research. For this study, a total of 21 items derived through extensive literature research and data research to understand what are the necessary competency factors for internal and external environmental changes in order for Korean venture companies to have global competitiveness in the era of the 4th Industrial Revolution. After reviewing SWOT factors by three expert groups and confirming them through Delphi survey, the importance of each item was analyzed by using AHP, a systematic decision-making technique. As a result of the analysis, it was shown that Strength(48%), Opportunity(25%), Threat(16%), Weakness(11%) were considered important in order. In terms of sub-items, 'quick and flexible commercialization capability', 'platform/big data/non-face-to-face service activation', and 'ICT infrastructure and it's utilization' were shown to be of the comparatively high importance. On the other hand, in the lower three items, 'macro-economic stability and social infrastructure', 'difficulty in entering overseas markets due to global protectionism', and 'absolutely inferior in foreign investment' were found to have low priority. As a result of the correlation verification by item to see differences in opinions by industry, academia, and policy expert groups, there was no significant difference of opinion, as industry and academic experts showed a high correlation and industry experts and policy experts showed a moderate correlation. The correlation between the academic and policy experts was not statistically significant (p<0.01), so it was analyzed that there was a difference of opinion on importance. This was due to the fact that policy experts highly valued 'quick and flexible commercialization', which are strengths, and 'excellent educational system and high-quality manpower' and 'creation of new markets' which are opportunity items, while academic experts placed great importance on 'support part of government policy', which are strengths. The implication of this study is that in order for Korean venture companies to secure competitiveness in the field of the 4th industrial revolution, it is necessary to have a policy that preferentially supports the relevant items of strengths and opportunity factors. The difference in the details of strength factors and opportunity factors, which shows a high level of variability, suggests that it is necessary to actively review it and reflect it in the policy.

• The Korean Journal of Air & Space Law and Policy
• /
• v.34 no.1
• /
• pp.159-201
• /
• 2019

Along with Annex 14 Volume I establishment in 1951 and the set-up of restriction surface around the runway, aeronautical technique and navigation performance achieved dazzling growth, and the safety and precision of navigation greatly improved. However, restrictions on surrounding obstacles are still valid for safe operation of an aircraft. Standards and criteria for securing safety of aircraft operating around and on airport is stated in Annex 11 Air Traffic Services and Annex 14 Aerodrome etc. In particular, Annex 14 Volume I presents the criteria for limiting obstacles around an airport, such as natural obstacles such as trees, mountains and hills to prevent collisions between aircraft and ground obstacles, and artificial obstacles such as buildings and structures. On the other hand, Annex 14 Volume I, in the application of the obstacles limitation surfaces, apply the exception criteria, as it may not be possible to remove obstacles that violate the criteria if the aeronautical study determines that they do not impair the safety and regularity of aircraft operation. Aeronautical study has been applied and implemented in various countries including United States, Canada and Europe etc. accordingly, Korea established and amended some provisions of the Enforcement rules of the Aviation Act and established the Aeronautical study guidelines to approve exceptions. However, because ICAO does not provide specific guidelines on procedures and methods of Aeronautical study, countries conducting aeronautical study have established and applied their own procedures and methods. Reflecting this realistic situation, at the 12th World Navigation Conference and at the 38th General Assembly, the contracting States demanded a reexamination of the criteria for current obstacle limitation surfaces and methods of aeronautical study, and the ICAO dedicated a team of experts to prepare new standard. This study, in line with the movement of international change in obstacle limitation surface and aeronautical study, aims to compare and analyze current domestic and external standards on obstacle limitation and height limits, while looking at methods, procedure and systems for aeronautical study. In addition, expecting that aeronautical study will be used realistically and universally in assessing the impact of obstacles, we would recommend the institutional improvement of the aeronautical study along with the development of quantitative analysis methods using the navigation data in the current aeronautical study.

• Journal of Wetlands Research
• /
• v.21 no.1
• /
• pp.34-42
• /
• 2019

Baseflow which is one of the unmeasurable components of streamflow and slowly flows through underground is important for water resource management. Despite various separation methods from researches preceded, it is difficult to find a significant separation method for baseflow separation. This study applied the MRC method and developed the improved approach to separate baseflow from total streamflow hydrograph. Previous researchers utilized the whole streamflow data of study period at once to derive synthetic MRCs causing unreliable results. This study has been proceeded with total nine areas with gauging stations. Each three areas are selected from 3 domestic major watersheds. Tool for drawing MRC had been used to draw MRCs of each area. First, synthetic MRC for whole period and two other MRCs were drawn following two different criteria. Two criteria were set by different conditions, one is flow condition and the other is seasonality. The whole streamflow was classified according to seasonality and flow conditions, and MRCs had been drawn with a specialized program. The MRCs for flow conditions had low R2 and similar trend to recession segments. On the other hand, the seasonal MRCs were eligible for the baseflow separation that properly reflects the seasonal variability of baseflow. Comparing two methods of assuming MRC for baseflow separation, seasonal MRC was more effective for relieving overestimating tendency of synthetic MRC. Flow condition MRCs had a large distribution of the flow and this means accurate MRC could not be found. Baseflow separation using seasonal MRC is showing more reliability than the other one, however if certain technique added up to the flow condition MRC method to stabilize distribution of the streamflow, the flow conditions method could secure reliability as much as seasonal MRC method.