• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.2
• /
• pp.83-96
• /
• 2011

Currently, the commonly used tunneling method in Korea is NATM (New Austrian Tunneling Method). This method uses the rock bolt, shotcrete, and supporting system to maintain the strength of original soil and ensures the stability of tunnel by stabilizing the soil using the original strength of the soil in maximum after the excavation. In past years, wire-mesh reinforced shotcrete was common ones but currently steel-fiber reinforced shotcrete is being widely used for the tunnel construction site in Korea to save construction time with the advanced construction technology. The results further indicate that needs for the establishment of not only the specifications for shotcrete but the strengthening methods for the under reinforced shotcrete sections. Therefore, this study deals with the development of a new steel-fiber to ensure the stability of tunnels that are under reinforced with steel-fibers and to overcome the shortcomings of conventional method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.1
• /
• pp.133-138
• /
• 2015

A weight sensor with a polarization maintaining photonic crystal fiber (PCF) is proposed and investigated by experimentally. The sensor system consists of a 3 dB fiber coupler, a half-wave plate, and light source. Wavelength shift induced by weight acting on the polarization maintaining PCF was measured. Two types of sensor patterns, circle type and straight type, were implemented and evaluated. The sensitivity of straight line type was 680 pm/kg and the circle type was 270 pm/kg, respectively. The both types of sensors have a good sensitivity and good linearity in the wide range.

• Radiation Oncology Journal
• /
• v.7 no.2
• /
• pp.299-303
• /
• 1989

Authors have developed highly reproducible calibration method for the Micro-Selectron HDR Ir-192 system (Nucletron, Motherland). The new jig has a 10cm radius circular hole in the $30cm{\times}30cm{\times}0.2cm$ acrylic plate, and 5F flexible bronchial tubes are attached around the hole. The source moves along the circle in the tubes and the ionization chamber is placed verticaly at the center of the circular hole (center of the jig). Dose distribution near the center was derived theoretically, and measured with the film dosimetry system. Theoretical calculation and measurement show the error margin below $0.1\%$ for 1mm or 2mm position deviation. We have measured at 12 and 24 points of circle with 1, 6, 11 and 21 second dwell time of source in order to calculate the activity of the source. Measurements have been repeated daily for 50 days. The accuracy and the reproducibility are below $1\%$ error margin. The half life of the source from our measurement is estimated $73.4\pm0.4$ days.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.46 no.1
• /
• pp.56-69
• /
• 2010

This study was intended to determine the maneuverability of the vessel CHARMBADA. When the rudder angle was at $10^{\circ}$, $20^{\circ}$ and $30^{\circ}$, the maximum advance by slow, half and full ahead were varied in the range of 523.6-131.3m, 528.8-177.2m and 530.6-219.7m, respectively. The maximum transfer was 799.9-181.3m, 792.1-232.8m and 807.7-316.9m, respectively. The turning circle ability was better during starboard turning. When the rudder angle was $10^{\circ}$, $20^{\circ}$ and $30^{\circ}$, variation in the maximum advances was 392.0m, 245.0m and 153.0m. The maximum transfer was 528.0m, 339.0m and 218.0m, respectively based on the regression equations. As the rudder angle became bigger, the maximum advance or maximum transfer became smaller by the exponential function. The advance inertia took 127sec, 145sec, 181sec each until the vessel speed was 7.0konts, 12.0konts, 17.0konts. The static inertia took 245sec, 269sec, 300sec each until the vessel speed was under 2.0konts and the advance distance was 114.4m, 181.2m, 197.0m each. Accordingly, the static inertia was inclined to increase to scale according to the increase in vessel speed. For the CHARMBADA, the smaller the rudder angle was, the much bigger the turning circle became due to adhesion to the skeg, thereby lowering the vessel's turning ability.

• Journal of the Korea Furniture Society
• /
• v.20 no.1
• /
• pp.61-70
• /
• 2009

This study intended to explore English of furniture tenn in relation to the joints and moldings in traditional Korean wood furniture, a base of Korean wood furniture, for the development of Korea furniture in the future. The joints such as butt joint, rabbeted joint, mitered joint, mortise-and-tenon joint, fist joint, and finger joint, and the moldings such as a piece of thread molding, half-circle molding, cove molding, flat molding, and triangle molding were analyzed between English and Korean language. The results were only basic terms which must be researched and unified in the traditional Korean furniture. Therefore, the terms in relation to the types, the details, the hardware, and so on, will have to be studied in terms of the meaning originated from the traditional craftsmen.

• The Korean Journal of Ceramics
• /
• v.5 no.4
• /
• pp.368-370
• /
• 1999

Using DC faced target sputtering method we grow AIN the films on the $Al_2O_3$(0001) substrate with varying thickness(17$\AA$-1000$\AA$). We measured x-ray diffraction(XRD) profiles by synchrotron radiation($\lambda$=1.12839 $\AA$) with four circle diffractometer. The full width half maximum(FWHM) of rocking curve for the AIN (0002) diffraction of the film grown at $500^{\circ}C$ was $0.029^{\circ}$. Also, we confirmed that the stress between AIN thin film and $Al_2O_3$(0001) substrate was reduced as increasing AIN film thickness, and the critical thickness of 400~500 $\AA$, defined as a lattice constant in the film agrees with that in a bulk without stress, was obtained.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.761-765
• /
• 1996

This paper describes the forging of circular tooth profiled gears as a series of development of simulator for non-axisymmetric parts that being used at the pump pulley, timing belt pulley etc. in automobiles. The half pitch of gear is divided into 6 deformation regious and kinematically admissible velocity fields for those regions are proposed. The neutral surface is introduced torepresent inner flow of material during forging operation with flat punch and, for each step, it is assumed as a circle. The upper bound solutions obtained from the suggested kinematically admissible velocity fields are in good agreement with experimental results and they are useful to predict the capacity of forging press for forging of circular gears.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.10a
• /
• pp.37-47
• /
• 1995

Forging of trapezoidal spline, serration and square spline with solid cylindrical billets and hollow one has been investigated by means of upper bound method. Kinematically admissible velocity fields for forging of splines have been proposed in this study. The half pitch of splines has been divided into deformation regons. The neutral surface is introduced into forging of splines with flat punch and, for each step, it is assumed as a circle with its radius rn upper bound solutions obtained obtained by proposed kinematically admissible velocity fields are useful to predict the loads for forging of splines.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.7 s.172
• /
• pp.79-87
• /
• 2005

This paper summarizes the work on the development of a simulation program for modelling the process of machining quasi-three dimensional shape with the excimer laser beam on a constantly moving polymers. Relatively simple masks of rectangle, triangle and half circle shape are considered. The etching depth is calculated by considering the number of laser pulses irradiated on the specimen surface. It was found that similar shapes as experimental results can be obtained by choosing suitable parameters of moving velocity, moving distance and mask sizes.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.1
• /
• pp.108-115
• /
• 1996

Forging of trapezoidal spline, serration and square spline with solid cylindrical billets and hollow one has been investigated by means of upper bound method. Kinematically admissible velocity fields for forging of splines have been proposed in this study. The half pitch of spline has been divided into several deformation regions. The neutral surface is introduced into forging of splines with flat punch and, for each step, it is assumed as a circle with its radius $r_n$. Upper bound solutions obtained by proposed kinematically admissible velocity fields are useful to predict the loads for forging of splines.