• 한국전자파학회논문지
• /
• 제15권11호
• /
• pp.1051-1061
• /
• 2004

본 논문에서는 반원형 및 반타원형 디스크가 급전점에 수직으로 로딩된 단순한 광대역 모노폴 안테나 구조에 급전점에는 추가적인 공진 구조를, 수직 모노폴 안테나의 끝단에는 수평으로 추가적인 소형 디스크가 로딩되는 초광대역 안테나의 특성에 관하여 시뮬레이션과 측정이 수행되었다. 설계된 초광대역 송신용 안테나로부터 가우시안 펄스의 전달 특성에 관하여 살펴보며 제안된 안테나의 수평방향을 단면으로 보았을 경우의 복사패턴이 등방향성 응답을 가짐을 알 수 있었다. 더욱이, 측정 및 시뮬레이션 결과로부터 소형이면서 광대역 특성을 보임을 알 수 있다. 제안된 수평방향의 소형 디스크가 장착된 반원형 디스크 모노폴 안테나의 측정결과로부터, 크기와 전기적인 성능 측면에서 살펴보았을 때 제안된 구조가 단순히 원형 디스크가 수직으로 로딩된 모노폴 안테나에 비해 견줄만 함을 알 수 있었다. 특히 본 논문을 통하여 제작된 안테나는 PCB를 이용한 프린팅 안테나에서 자주 발생되는 표면파 손실 및 유전체 손실과 같은 현상이 발생되지 않으므로 Return Loss의 성능이 곧 복사되는 효율과 밀접한 관계가 있다.

• 마이크로전자및패키징학회지
• /
• 제14권3호
• /
• pp.65-71
• /
• 2007

칩 스택 패키지에 적용을 위해 폭 $75{\sim}10\;{\mu}m$, 길이 3mm의 트랜치 비아에 대해 도금전류밀도 및 rotating disc electrode(RDE)의 회전속도에 따른 Cu filling 특성을 분석하였다. RDE 속도가 증가함에 따라 트랜치 비아의 Cu filling 특성이 향상되었다. 트랜치 비아의 반폭 길이, 즉 트랜치 비아 폭의 1/2 길이와 이 트랜치 비아에 대해 95% 이상의 Cu filling 비를 얻기 위한 RDE 최소속도 사이에는 Nernst 관계식이 성립하여, 95%이상의 Cu filling비를 얻을 수 있는 최소 트랜치 비아의 반폭 길이는 RDE 속도의 제곱근의 역수에 직선적으로 비례하였다.

• Imaging Science in Dentistry
• /
• 제52권4호
• /
• pp.409-413
• /
• 2022

This report presents a rare case where a displaced temporomandibular joint (TMJ) disc was reduced to its normal position after orthognathic surgery, and long-term magnetic resonance imaging (MRI) follow-up visualized these postoperative changes. A 22-year-old male patient presented for facial asymmetry. He also complained of pain in the right TMJ area, and MRI showed disc displacements in both TMJs. After orthognathic surgery for facial asymmetry correction, the TMJ was re-evaluated. The symptom had resolved and the disc was positioned within the normal range during mouth opening. However, 6 and a half years after surgery, he complained of recurrent pain in the right joint, and MRI revealed medial disc displacement in the right TMJ. In conclusion, the influence of orthognathic surgery on the disc position might continue for a long time until the TMJ adapts to the new position. Careful and long-term follow-up is suggested to assess the TMJ complex.

• 한국소음진동공학회논문집
• /
• 제18권5호
• /
• pp.558-563
• /
• 2008

Vibration/shock affects biggest taking a train subtraction of vehicle and durability decline. Therefore, absorber is used for vibration/shock isolation and various qualities of the material and design are applied to isolation. This paper proposes vibration/shock absorber that applies 'Disc' spring. Through comparison with 'Disc' spring that has nonlinearity and coil spring that is having linearity, see effect that nonlinearity of isolation gets in vibration/shock Isolation. Coil spring and 'Disc' spring are non-linear numerical analysis and simulation through theory for this, get and investigate comparison result through an experiment finally. Expressed and formulated shock through 'Runge-Kutta' method/impact response to nonlinear-vibration-equation of 1 degree of freedom for numerical analysis. Double half sine pulse of excitation used and analyzed result through spectrum response analysis here. Response of disc spring is compared to response of coil spring by changing $h_o/t$ ratio with computer simulation and the usage of disc spring is increased through analysis of effect of design factors. The purpose of this paper is that the shock response of disc spring is calculated through numerical simulation and to design the optimal absorber under the limited condition. And then, the isolation effect was analyzed through the shock test.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.990-993
• /
• 2008

Vibration/shock affects biggest taking a train subtraction of vehicle and durability decline. Therefore, absorber is used for vibration/shock isolation and various qualities of the material and design are applied to isolation. This paper proposes vibration/shock absorber that applies 'Disc'spring. Through comparison with 'Disc' spring that has nonlinearity and coil spring that is having linearity, see effect that nonlinearity of isolation gets in vibration/shock isolation. Coil spring and 'Disc' spring are non-linear numerical analysis and simulation through theory for this, get and investigate comparison result through an experiment finally. Expressed and formulated shock through 'Runge-Kutta' method/impact response to nonlinear-vibration-equation of 1 degree of freedom for numerical analysis. Double half sine pulse of excitation used and analyzed result through spectrum response analysis here. Response of disc spring is compared to response of coil spring by changing ho/t ratio with computer simulation and the usage of disc spring is increased through analysis of effect of design factors. The purpose of this paper is that the shock response of disc spring is calculated through numerical simulation and to design the optimal absorber under the limited condition. And then, the isolation effect was analyzed through the shock test.

• The Korean Journal of Pain
• /
• 제14권2호
• /
• pp.199-206
• /
• 2001

Background: The lumbar sympathetic ganglia are variable in both position and numbers. The aim of this study was to detect the appropriate lumbar vertebral level where the lumbar sympathetic ganglia primarily aggregate. Methods: Forty patients comprising of hyperhidrosis (26 cases), complex regional pain syndrome (10 cases), peripheral artery occlusion disease (3 cases) and postherpetic neuralgia (1 case) underwent lumbar sympathetic block. We randomly selected one of two (L2 or L3) levels and the L4 level. The position of the needle tip and distribution of dye was verified by injection of a mixture of radio-opaque dye (1.5 ml) and 4% lidocaine (1.5 ml) and subsequently confirmed by L-spine anteroposterior and a lateral view X-ray. We considered the response positive when the skin temperature increased more than $1^{\circ}C$ in 5 min. Results: In general, the positive response ratio was greater when the needle tip located at the L2 or L4 level vice L3 and when the drug was distributed on the lower half of the L4 body and in the L4/5 intervertebral disc space. In a right side block, the positive response ratio was greater when the drug was distributed on the lower half of the L4 body and in the L4/5 intervertebral disc space, although in a left side block there was no significant difference seen between the levels. The complications of the neurolytic block were alcohol neuritis (7.5%) and hypoesthesia (5%) on the L1 or L2 dermatome. Conclusions: The best effect with least chance of complication may be induced by spreading the drug on the lower half of the L4 body and/or into the L4/5 intervertebral disc space by placing the needle tip on the L4 body.

• 대한치과교정학회지
• /
• 제15권2호
• /
• pp.271-277
• /
• 1985

With modification of the acid etch technique and improvements of the physical and mechanical properties of the acrylic resin, the removal of directly bonded attachments and the finishing of the underlying enamel have become an acute clinical problem. This study was to evaluation the efficacy of recently introduced instrumentation and techniques to remove bonded brackets and residual resin, and restore the affected enamel surface to an acceptable clinical condition. Fortyeight premolar which were scheduled for extraction for orthodontic purposes were bonded with brackets using super-C ortho. Four additional premolars with untreated surfaces were used as controls. After one weak the brackets were removed and the residual resin removed by hand scaler, green stone, green rubber wheel, sandpaper disc, tungsten carbide bur, Sof-lex disc. Half the experimental teeth were given a final pumicing and then all were extracted and stored in 50 percent ethanol. The scanning electron microscopy was used to evaluated the enamel surface. Following results were obtained; 1. A satisfactory result was obtained by means of the Sof-lex disc. 2. The order of the scratch formation was the procedure using hand scaler, green atone, tungsten carbide bur, sandpaper disc, green rubber wheel, and Sof-lex disc. 3. The procedures using green stone and tungsten carbide bur showed many groove formations and the other procedures showed none. 4. final pumicing serves effectively to remove residual adhesive and restore the enamel surface.

• Journal of Korean Neurosurgical Society
• /
• 제30권sup2호
• /
• pp.242-246
• /
• 2001

Objective : The short hospitalization or outpatient care for patients undergoing laminectomy is not popular practice in Korea. We evaluated the clinical and economical significance of short hospitalization for patients undergoing microdiscectomy for their lumbar disc herniation. Material and Methods : From March 1999 to December 2000, patients were hospitalized for intended short period hospitalization for lumbar disc surgery. Their radiological and clinical data were analyzed for their clinical and economical results. We compared these data with 20 patients who hospitalized conventionally. Results : Total of 64 patients were evaluated. Three were lost to follow-up. Mean postoperative hospitalization period is 2.0 days(excluding one patient). Excellent to good outcome was achieved in 90.6 % of the patients. They payed about half expenses for hospitalization compared with conventional group. Their mean number of outpatient visit was 3.0. Conclusion : Short hospitalization for lumbar disc surgery is an acceptable option in Korea. It is also economically beneficial while achieving acceptable clinical results.

• Design & Manufacturing
• /
• 제17권1호
• /
• pp.20-26
• /
• 2023

Lab-on-a-disc is a circular disc shape of cartridge that can be used for blood-based liquid biopsy to diagnose an early stage of cancer. Currently, liquid biopsies are regarded as a time-consuming process, and require sophisticated skills to precisely separate cell-free DNA (cfDNA) and circulating tumor cells (CTCs) floating in the bloodstream for accurate diagnosis. However, by applying the lab-on-a-disc to liquid biopsy, the entire process can be operated automatically. To do so, the lab-on-a-disc should be designed to prevent blood leakage during the centrifugation, transport, and dilution of blood inside the lab-on-a-disc in the process of liquid biopsy. In this study, the main components of lab-on-a-disc for liquid biopsy are fabricated by injection molding for mass production, and ultrasonic welding is employed to ensure the bonding strength between the components. To guarantee accurate ultrasonic welding, the flatness of the components is optimized numerically by using the response surface methodology with four main injection molding processing parameters, including the mold & resin temperatures, the injection speed, and the packing pressure. The 27 times finite element analyses using Moldflow® reveal that the injection time and the packing pressure are the critical factors affecting the flatness of the components with an optimal set of values for all four processing parameters. To further improve the flatness of the lab-on-a-disc components for stable mass production, a quarter-disc shape of lab-on-a-disc with a radius of 75 mm is used instead of a full circular shape of the disc, and this significantly decreases the standard deviation of flatness to 30% due to the reduced overall length of the injection molded components by one-half. Moreover, it is also beneficial to use a quarter disc shape to manage the deviation of flatness under 3 sigma limits.

• Journal of Korean Neurosurgical Society
• /
• 제60권4호
• /
• pp.433-440
• /
• 2017

Objective : Although minimally invasive posterior cervical foraminotomy (MI-PCF) is an established approach for motion preservation, the outcomes are variable among patients. The objective of this study was to identify significant factors that influence motion preservation after MI-PCF. Methods : Forty-eight patients who had undergone MI-PCF between 2004 and 2012 on a total of 70 levels were studied. Cervical parameters measured using plain radiography included C2-7 plumb line, C2-7 Cobb angle, T1 slope, thoracic outlet angle, neck tilt, and disc height before and 24 months after surgery. The ratios of the remaining facet joints after MI-PCF were calculated postoperatively using computed tomography. Changes in the distance between interspinous processes (DISP) and the segmental angle (SA) before and after surgery were also measured. We determined successful motion preservation with changes in DISP of ${\leq}3mm$ and in SA of ${\leq}2^{\circ}$. Results : The differences in preoperative and postoperative DISP and SA after MI-PCF were $0.03{\pm}3.95mm$ and $0.34{\pm}4.46^{\circ}$, respectively, fulfilling the criteria for successful motion preservation. However, the appropriate level of motion preservation is achieved in cases in which changes in preoperative and postoperative DISP and SA motions are 55.7 and 57.1%, respectively. Based on preoperative and postoperative DISP, patients were divided into three groups, and the characteristics of each group were compared. Among these, the only statistically significant factor in motion preservation was preoperative disc height (Pearson's correlation coefficient=0.658, p<0.001). The optimal disc height for motion preservation in regard to DISP ranges from 4.18 to 7.08 mm. Conclusion : MI-PCF is a widely accepted approach for motion preservation, although desirable radiographic outcomes were only achieved in approximately half of the patients who had undergone the procedure. Since disc height appears to be a significant factor in motion preservation, surgeons should consider disc height before performing MI-PCF.