• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.633-634
• /
• 2009

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.173-173
• /
• 2000

This paper discusses a observer based discrete-time controller design and presents a modified control structure for dual-stage hard disk drive systems using piezoelectric microactuator(MA). In plant modeling, dynamic coupling between VCM and MA is not considered. Each controller is organized independently and designed using pole placement. Simulation result shows that 4th-order controller achieves about 3kHz servo bandwidth and 0.22msec of 2% settling time.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.232-236
• /
• 2000

To provide model parameters for servo control system design, dynamic characteristics of a piezoelectric microactuator for hard disk drive(HDD) were investigated. At first frequency response characteristics was measured and a second order model was proposed. Here the amplitude dependent dynamic characteristics such as low frequency gain and damping ratio were studied. In addition, the load current and equivalent impedance of the piezoelectric actuator were measured by varying excitation voltage and frequency. At last, the super-harmonic resonance of the piezoelectric actuator was discussed.

• 한국정밀공학회지
• /
• 제18권4호
• /
• pp.9-18
• /
• 2001

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.128-135
• /
• 2006

This paper presents a finite element method to analyze the free vibration of a flexible HDD composed of the spinning disk-spindle system with fluid dynamic bearings(FDBs), the head-suspension-actuator with pivot bearings, and the base plate with complicated geometry. Experimental modal testing shows that the proposed method well predicts tue vibration characteristics of a HDD. This research also shows that even the vibration motion of the spinning disk corresponding to half-speed whirl and the pure disk mode are transferred to a head-suspension-actuator and base plate through the air bearing and the pivot bearing consecutively. The proposed method can be effectively extended to investigate the forced vibration of a HDD and to design a robust HDD against shock.

• 한국소음진동공학회논문집
• /
• 제17권1호
• /
• pp.24-32
• /
• 2007

This paper presents a finite element method to analyze the free vibration of a flexible HDD composed of the spinning disk-spindle system with fluid dynamic bearings(FDBs), the head-suspension-actuator with pivot bearings, and the base plate with complicated geometry. Experimental modal testing shows that the proposed method well predicts the vibration characteristics of a HDD. This research also shows that even the vibration motion of the spinning disk corresponding to half-speed whirl and the pure disk mode are transferred to a head-suspension-actuator and base plate through the air bearing and the pivot bearing consecutively. The proposed method can be effectively extended to investigate the forced vibration of a HDD and to design a robust HDD against shock.

• 정보저장시스템학회논문집
• /
• 제1권1호
• /
• pp.99-107
• /
• 2005

According to recent trend, hard disk drive(HDD) has been smaller and less weight. Therefore, it needs new method of writing position information. In this thesis, a new controller that is suitable for SSW is proposed. The controller accepted SSW technology that is used to write position information in current HDD industry. The important condition to perform SSW is to reach constant velocity decided from the head velocity profile as fast as possible. The constant velocity decides the positional accuracy of spiral pattern and setup time decides the capacity of HDD. The head velocity profile as a reference signal must be designed not to cause resonance mode. The proposed controller was designed with consideration of these 3 elements, and it properly works for SSW. The velocity profile designed with SMART control not only minimizes the jerk, but also does not cause the resonance mode of a plant. After designing a conventional PID controller, it compared with electrical spring technique and ZPET technique.

• 정보처리학회논문지A
• /
• 제9A권1호
• /
• pp.93-98
• /
• 2002

본 논문에서는 하드디스크 드라이브 읽기 채널용 아날로그/디지털 변환기를 설계하였다. 본 회로는 고속 저에러율 비교 동작이 가능한 빠른 regenerative autozero 비교기에 기반을 두고 있고, 아키텍쳐에 Double Speed Dual ADC(DADA) 방식을 사용하여 전체 A/D 변환기의 속도를 효과적으로 향상시켰다. 또한 autozero 구조에 적합한 새로운 타입의 thermometer-to-binary 디코더를 사용하여 글리치를 제거하였고 기존의 구조를 보다 최적화시켰다. 이 ADC는 6-bit, 해상도, msample/s 최대 변환속도로 설계되었으며, 390mW 전력 소모와 한 클럭주기의 latency를 가진다. 설계에 0.65m CMOS 공정을 사용하였다.

• Design & Manufacturing
• /
• 제2권5호
• /
• pp.43-47
• /
• 2008

Micro Electrochemical Machining(Micro ECM) has traditionally been used in highly specialized fields such as those of the aerospace and defense industries. It is now increasingly being applied in other industries where parts with difficult-to-cut material, complex geometry and tribology such as compute. hard disk drive(HDD) are required. Pulse Electrochemical Micro-machining provides an economical and effective method for machining high strength, high tension, heat-resistant materials into complex shapes such as turbine blades of titanium and aluminum alloys. Usually aluminum alloys are used bearings to hard disk drive in computer. In order to apply aluminum alloys to bearing used in hard disk drive, this paper presents the characteristics of Micro ECM for aluminum alloy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.214-217
• /
• 2002

Micro Surface Electrochemical Machining has traditionally been used in highly specialized fields such as those of the aerospace and defense industries. It is now increasingly being applied in other industries where parts with difficult-to-cut material, complex geometry and tribology such as compute. hard disk drive(HDD) are required. Pulse Electrochemical Micro-machining provides an economical and effective method for machining high strength, high tension, heat-resistant materials into complex shapes such as turbine blades of titanium and aluminum alloys. Usually aluminum alloys are used bearings to hard disk drive in computer. In order to apply aluminum alloys to bearing used in hard disk drive, this paper presents the characteristics of Micro Surface Electrochemical machining for aluminum alloy.