• Journal of the Korean Institute of Landscape Architecture
• /
• v.42 no.6
• /
• pp.50-59
• /
• 2014

This experiment was performed in order to study the relationship between physical properties of soil and the growth characteristics of Sedum reflexum. A correlation analysis and multiple regression analysis were performed using SPSS Ver 19.0 for Windows. The multiple regression analysis results of soil physical properties and growth characteristics were as follows. The regression equation: The length=$.993-14.070^*$(soil bulk density)+$.233^*$(solid phase)+$.038^*$(liquid phase)+$.068^*$(permeability). The significance of soil bulk density and solid phase was great. The width=$2.931-33.925^*$(soil bulk density)+$.566^*$(solid phase)+$.206^*$(liquid phase)+$.027^*$(permeability). The significance of soil bulk density and solid phase was great. The wet weight and dry weight of the upper and lower and soil physical properties did not have a direct relationship.

• Journal of Korea Foundry Society
• /
• v.6 no.1
• /
• pp.12-19
• /
• 1986

This study was undertaken to understand the formation mechanism of the hard spots in high strength brass. To investigate the behavior of the hard spots in the isothermal liquid state with varying silicon content, the rapidly quenched specimens were obtained by suctioning the melt into the silica tube and water quenching. To examine the growth process of the hard spots with holding time, the unidirectional solidification technique was used. The results of this study are summarized as follows: 1) With the addition of Fe in order to get the effects of grain refinement in high strength brass, the two different type of Fe-rich phases are occurred, which are defined as dendritic and globular phase. The chemical composition of the globular phase was different from that of the dendritic phase in that the globular phase contained Si. 2) With increasing Si content, the Fe-rich phase had a tendency to form globular phase. 3) As the holding time increased in the liquid state, globular was also prone to coalesce. The further growth of globular phase to large size was due to reducing the interfacial energy. 4) The primary phase of copper alloy was nucleated preferentially on the dendritic phase. It was noticeable that the dendritic phase acted as a grain refiner. However, the agglomerate (hard spots) which was composed of the globular phase decreased the mechanical properties of high strength brass. 5) Once the hard spots formed in the high strength brass casting, it was very difficult to remove them. This is due to the fact that their meting temperature is higher than the pouring temperature of high strength brass.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.528-528
• /
• 1996

• Korean Journal of Veterinary Service
• /
• v.30 no.3
• /
• pp.291-304
• /
• 2007

Mutants of an obligate aerobic bacterium, Vitreoscilla, that have deficiency in heat-labile catalase-peroxidase hydroperoxidase I (HPI) were created by EMS treatment. The catalase-peroxidase HPI-deficient mutant showed substantially lower peroxidase activity in exponential and mid-stationary phase compared with the wild type strain. In late stationary phase, the mutant exhibited no peroxidase activity. Peroxidase deficiency in the mutant was revealed by polyacrylamide gels stained for peroxidase activity. Characteristically, catalase levels in the mutant increased about 14- and 8-fold during growth in the exponential and stationary phases, respectively, compared to those in the wild type, suggesting a compensatory effect for protection from $H_2O_2$ toxicity. The mutant showed differences in physiology from the wild type: retardation in growth rate and decrease in oxygen consumption. Both the wild type and the catalase-peroxidase HPI-deficient mutant of Vitreoscilla had lower growth rates in media containing increasing $H_2O_2$ concentrations. However, the mutant exhibited an additionally decreased growth rate after 6 to 8 h of growth compared to the wild type. The wild type was resistent up to 20 mM $H_2O_2$, whereas the mutant was very sensitive to high concentrations of exogenous $H_2O_2$. Although elevated catalase levels would provide protection of the bacteria from the deleterious effect of $H_2O_2$, it did not appear to be complete. Cell-free extracts of the mutant showed decreased NADH oxidation rates and higher accumulation of $H_2O_2$ during this oxidation. These results may account for the impaired growth and earlier onset of death phase by the catalase-peroxidase HPI-deficient mutant of Vitreoscilla.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.463-469
• /
• 1999

The potassium lithium niobate $K_3$$Li_2$$Nb_5$$O_{15}$ single crystals were growing in $K_x$$Li_{1-x}$$NbO_3$ (x = 0.4~0.6) chemical formular by the Czorchralski method. Crystal growth is studied in two orientations with growth along a-axis and c-axis. We have subjected this crystal to x-ray diffraction studies and found that they are single-crystalline and belong to tetragonal system with the lattice parameters a = b = 12.577 $\AA$ and c = 3.997$\AA$. The temperature dependence of dielectric constant was measured in the region of the phase transition. Curie temperature and diffuseness of phase transition are influenced by composition concentration. The composition and cation distribution of ferroelectric TB-type niobate crystals has a strong influence on the ferroelectric properties. Growth condition, optical transmittance, etching pattern and dielectric properties are presented and discussed.

• Microbiology and Biotechnology Letters
• /
• v.9 no.4
• /
• pp.225-230
• /
• 1981

The kinetic study of rifamycin B production in batch culture of Nocardia mediterranei was undertaken in part of our endeavor to optimize the fermentation condition. The growth parameters such as $\mu$$_{m}$ and Ks values for nitrogen source were evaluated by employing Monod equation. From the experiments, $\mu$$_{m}$ and Ks were 0.15hr$^{-1}$ and 8.35g/1, respectively. The growth kinetics in batch culture was found successfully interpreted by logistic law, i.e., the initial specific growth rate and the maximum cell mass concentration were determined as function of pH and both found to have maxima. For the production of rifamycin B, a non-growth associated production kinetics was employed and the specific productivity as a function of pH was found to have two maximum points. The yield coefficient and the specific productivity were calculated as mean values in production phase. Utilizing these experimental data as a function of pH, the optimal condition for the rifamycin B production was discussed with regad to the pH effect on the cell growth and production of the antibiotic. As a result, growth phase at pH 6.5 and production phase at pH 7.0 were found to be recommended.ded.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.4
• /
• pp.343-350
• /
• 2003

Using Bi$_2$Sr$_2$Ca$_2$.$_2$Cu$_3$ $O_{x}$ powders prepared by solid state reaction and spray drying method, the nucleation and growth behaviors of superconducting and second phases were investigated during isothermal heat treatment. When the spray drying power was used in contrast with solid state reaction powder, Bi$_2$Sr$_2$Ca$_2$.$_2$Cu$_3$ $O_{x}$ (2223) phase could be formed at the relatively shot time and second phases were much bigger. Quantitative analysis showed that as the heat treatment time increased, more Bi$_2$Sr$_2$Ca$_2$.$_2$Cu$_3$ $O_{x}$ (2212) changed to 2223 and the major second phase was changed from (Sr,Ca)$_{14}$Cu$_{24}$ $O_{x}$(14:24) to (Sr,Ca)$_2$Cu$_1$ $O_{x}$ (2:l). The superconducting phase formed at the relatively short time 14:24 phase. Following the Bi-free phase of 14:24 Phase, but long time was needed in places far from the 14:24 phase. Following the formation of the 2212 phase near the 14:24 phase, the 2223 phase nucleated preferentially at the interface between the 2212 and 14:24 phases. The preferential nuclcation of 2223 was explained by its structural similarity and low Interfacial energy with both the Bi-free and 2212 Phases.12 Phases.

• Journal of the Korean Ceramic Society
• /
• v.34 no.5
• /
• pp.483-490
• /
• 1997

Al2O3/metal composites were fabricated by oxidation and reaction of molten Al-alloy into two types of commercial Al2O3-SiO2 fibrous insulation board. The growth rate, composition and microstructure of these materials were described. An AlZnMg(7075) alloy was selected as a parent alloy. Mixed polycrystalline fiber and glass phase fiber were used as a filler. The growth surface of an alloy was covered with and without SiO2. SiO2 powder was employed as a surface dopant to aid initial oxidation of Al-alloy. Al-alloy, SiO2, fiber block and growth inhibitor CaSiO3 were packed sequentially in a alumina crucible and oxidized in air at temperature range 90$0^{\circ}C$ to 120$0^{\circ}C$. The growth rate of composite layer was calculated by measuring the mass increasement(g) per unit surface($\textrm{cm}^2$). XRD and optical microscope were used to investigate the composition and phase of composites. The composite grown at 120$0^{\circ}C$ and with SiO2 dopant showed rapid growth rate. The growth behavior differed a little depending on the types of fiber used. The composites consist of $\alpha$-Al2O3, Al, Si and pore. The composite grown at 100$0^{\circ}C$ exhibited better microstructure compared to that grown at 120$0^{\circ}C$.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1107-1116
• /
• 2006

The droplet ejection process driven by an evaporating bubble in a thermal inkjet printhead is investigated by numerically solving the conservation equations for mass, momentum and energy. The phase interfaces are tracked by a level set method which is modified to include the effect of phase change at the interface and extended for multiphase flows with irregular solid boundaries. The compressibility effect of a bubble is also included in the analysis to appropriately describe the bubble expansion behaviour associated with the high pressure caused by bubble nucleation. The whole process of bubble growth and collapse as well as droplet ejection during thermal inkjet printing is simulated without employing a simplified semi-empirical bubble growth model. Based on the numerical results, the jet breaking and droplet formation behaviour is observed to depend strongly on the bubble growth and collapse pattern. Also, the effects of liquid viscosity, surface tension and nozzle geometry are quantified from the calculated bubble growth rate and ink droplet ejection distance.

• Journal of Plant Biology
• /
• v.20 no.2
• /
• pp.63-69
• /
• 1977

Experiments were conducted to investigate the effects of several hormones on the growth of suspension culture of carrot (Daucus carota L.) cells, where changes in pH and the amount of $NH_4-Nin$ the medium were observed with regard to growth. A treatment with 2,4-D at $10^{-5}M$ resulted in a highest rate of growth; the hormone at this concentration caused an increase in dry weight by about 40 to 50% over the control, measured at a stationary phase. It was thus indicated that 2,4-D at $10^{-5}M$ provided the optimal condition for the suspension culture. Changes in pH of the medium were found to be affected by hormonal treatments during the first 2-3 days following the inoculation, after which the pattern of pH changes in hormone enriched media paralleled that of the control. Subsequent changes of $NH_4-N and NO_3-N$ from the medium by the cells, and also by growth of the cells. The uptake of $NH_4-N$ by the cells did not appear to be influenced by hormonal treatments. At a stationary phase, a considerable amout of $NO_3-N$ played a more important role than $NH_4-N$ in the growth of the carrot cell suspension culture.