• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.5
• /
• pp.697-702
• /
• 2010

A WIG(Wing-In-Ground effect) craft flies close to the water surface by utilizing a cushion of relatively high pressurized air between its wing and water surface. This implies that when one designs such craft it is important to have lightweight structures with adequate strength to resist external loads with some margins. To investigate this requirement, this paper deals with the structural analysis of the bottom plate of small WIG craft having a design landing weight of 1.2-ton. As building materials for the WIG craft, pre-preg carbon/epoxy composites are considered. The strength information of the bottom plate is obtained using the first-ply-failure analysis in conjunction with a mid-plane symmetric laminated plate theory. As a result, the first-ply-failure location, load and deflection of the bottom plate are obtained. The calculated strength information is compared with the water reaction load for the bottom plate of seaplanes considered when they land on the water surface -the same fluid-structure interaction mechanism as that of WIG craft. In the calculation of seaplane water reaction load information, the rules shown in FAR(Federal Aviation Regulations) Part 25 are used. Through the comparison, the structural integrity of the bottom plate for the WIG craft is checked.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.9
• /
• pp.1308-1312
• /
• 2013

In this paper, carried out for optimal ground system for ensuring safety for electricity used to power equipment in the 20 kHz frequency. Now the grounding system of the mesh electrode, electrode rods are installed for power plant safety and protection against electric shock. However, the electrical equipment grounding system in the 20 kHz were considering the increasing grounding impedance due to the high frequency and the magnetic shielding. But until now, there has been little research on the grounding system. To solve this problem, In this paper was proposed optimal grounding system due to the experiment using a mesh electrode, rod electrode, aluminum plate electrodes. Measurement results, grounding resistance was depending on the material of the electrode grounding resistance. In addition, the leakage current (induced) appeared to be affected depending on the type of electrode.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.5
• /
• pp.2001-2006
• /
• 2017

This paper explains the effects of the weak signal of a rotating-type electric field mill sensor fabricated for measuring the intensity of the electric field generated by high-voltage direct current (HVDC) power transmission lines. The fabricated field mill consists of two isolated electrode vanes, a motor driver, and a ground part. The sensor plate is exposed to and shielded from the electric field by means of a rotary shutter consisting of a motor-driven mechanically complementary rotor/stator pair. When the uncharged sensor plate is exposed to an electric field, it becomes charged. The rotating electrode consists of several conductive vanes and is connected to the ground part, so that it is shielded. Determining the appropriate design variables such as the speed of the vane, its shape, and the distance between the two electrodes, is essential for ensuring optimal performance. By varying the speed, the weak signal characteristics which is used to signal processing and calibration experiment are quite different. Each weak signal pattern was analyzed along with the output voltage characteristics, in order to be able to determine the intensity of the electric field generated by HVDC power transmission lines with accuracy.

• Korean Journal of Optics and Photonics
• /
• v.9 no.3
• /
• pp.129-133
• /
• 1998

The phtocount distributions of a quasi-thermal light source were measured by using the photoelectric counting method. The source was fabricated from the ground glass plate of 9${\mu}{\textrm}{m}$ roughness illuminated by linearly polarized He-Ne laser beam. The coherence time of the quasi-thermal light changed from 31.4$mutextrm{s}$ to 2.48$mutextrm{s}$ according to the grain velocity of the ground glass plate. The photocount distribution showed the Bose-Einstein statistics for a long coherence time compared to the counting time interval, while the distribution approaches the Poisson distribution when the coherence time much shorter than the counting time.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.974-981
• /
• 2005

Because general laboratory tests for sand compaction pile method including unit-cell test device have fixed outside diameter, as area replacement ratio increase, diameter of sand pile increase. These condition can bring about overestimation of stiffness of composite ground. In addition, existing large soil box which consist of bellows type loading plate can occur serious mistake in checking the amount of drained water because there are additional drainage along the inside wall in device. Overcoming these shortcoming, this paper developed modified large scale soil box consist of piston type load plate. In this study, using this device, series of modified large scale soil box tests were performed, and investigated the settlement and stress transportation characteristics with area replacement ratio in sand compaction pile method.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.2
• /
• pp.5-14
• /
• 2012

CMV(Compaction Meter Value) obtained from compaction results using an accelerometer, which measures the impact on the ground and the resilient force of the ground, is compared with the other degree of compaction through regression analysis. As a result, there is no correlation between results from conventional test methods (e.g., the plate load test and field density test) and the degree of compaction evaluated by either the Geogauge or the dyanamic cone penetrometer. To assess the possibility of replacing the conventional test methods with new test methods using CMV, several degrees of compaction tests were carried out. Those results show that the CMV obtained from compaction results using an accelerometer can be used as a substitute for conventional methods to evaluate the stiffness characteristics of compacted soil.

• Journal of Environmental Health Sciences
• /
• v.21 no.1
• /
• pp.7-20
• /
• 1995

The aims of this study are to enhance the students' knowledge of the drinking water and its reliability by investigating drinking water situation on the drinking water. The results are as following 1. Status and drinking behavior about school drinking water (1) 97.82% of the schools are using the tap water as the resource of drinking water. (2) 46 schools are in possession of water tank and 18 schools of them are using the water tank as the resource of drinking water. The clearing and sanitization of the tank are carried out once in a year with hypochloronatrium by the low-level officials. (3) 51.28% of the schools are providing the students with drinking water and 75% of them with boiled water. The drinking water supply managers are low-level officials, nurse teachers, and dietitian. 2. Analysis of the drinking water quality (1) Most of the drinking water provided by the school are tap water 35.8%, barely tea 5.85%, filtered water 6.3%, ground water 1.1% and all turned out to be suitable for drinking. (2) The drinking water carried from home turned out to be unsuitable for drinking except pH criterion, especially the test of APC(Aerobic Plate Count) and Coliform group showed worse degree. These results were caused by the hygiene problem and maltreatment in water container.

• Journal of the Korean Society of Safety
• /
• v.28 no.1
• /
• pp.18-23
• /
• 2013

The purpose of this study were to develop and validate a prototype slipmeter used on-site floor. The developed slipmeter was dreg sled type. It measured static coefficient of friction(SCOF). The developed slipmeter was evaluated with ASTM 2508-11 which use four different standard surfaces(polished granite, glazed porcelain, vinyl composite tile, and ceramic tile). The SCOF was then measured with developed slipmeter under the three different contaminants and seven different floors. The test results of slipmeter were also compared with those of BOT-3000, floor surface roughness, and human perception. The test results revealed that developed slipmeter successfully ranked all four standard surfaces and differentiated among standard surfaces with varying degrees of slipperiness. The developed slipmeter couldn't properly measure slipperiness under the two kind of floors(polished tile, ground steel plate) and one kind of contaminant(glycerol). The test results of developed slipmeter had stronger correlation with those of BOT-3000 and floor roughness under the water and detergent solution than under the glycerol. The test results of developed slipmeter also showed stronger correlation with those of BOT-3000 and surface roughness than those of human perception. The newly developed slipmeter had been found to give consistent results under the test conditions except for two kind of floors(polished tile, ground steel plate) and one kind of contaminant(glycerol).

• Journal of the Korean GEO-environmental Society
• /
• v.10 no.6
• /
• pp.5-18
• /
• 2009

In construction of buildings in Korea, the buildings are frequently founded on the weathered ground (weathered soil/rock, fractured rock). In this case, to make a full use of a bearing capacity of a weathered ground for economic design, the shallow mat foundation system could be used. In this study, we have researched three cases of mat foundations on the weathered ground in Korea, and analyzed and considered the design procedures and the reinforcing methods. That is, we have considered the detail design, analysis proceedings, the ground settlement evaluation proceedings, the rock face mapping evaluations after excavation and reinforcing methods of the mat foundation on the weathered ground. And large scale plate load tests on the weathered ground supporting the mat foundation were performed and also load bearing capacity and settlement of actual mat foundation, considering the scale effect, were evaluated.

• Journal of the Society of Disaster Information
• /
• v.17 no.4
• /
• pp.786-793
• /
• 2021

Purpose: An experiment was conducted to analyze the characteristics of the settlement of soft clay soil in the central region of the west coast of Korea, which has a high silt content and is difficult to predict settlement due to various stress histories. Method: Field experiments were conducted for three cases. The settlement amount of the subsidence plate was measured in each case, and the following conclusions were drawn by analyzing Terzaghi's one-dimensional consolidation settlement amount, both the hyperbolic method and the Asaoka method. Result: The predicted value by Terzaghi was analyzed to be the largest in all cases, and it was predicted to be 111% to 187% larger than the subsidence plate settlement value. That is, the subsidence plate settlement value, which is the amount of settlement of the actual ground, showed a settlement of 53.4~89.9% compared to the predicted value of Terzaghi. Therefore, it was analyzed that the expected settlement of the Terzaghi method in the clay soft ground of the central west coast of Korea is more than the actual settlement. Conclusion: It was analyzed that the Asaoka method and the hyperbolic method presented relatively similar results, and in practice, predicting the settlement amount smaller than the actual settlement amount may cause a risk, so the hyperbola analysis method predicted 6~14% larger than the actual settlement amount can be used as a safety side.