• Journal of Ecology and Environment
• /
• v.41 no.4
• /
• pp.114-119
• /
• 2017

This study tried to analyze error range and resolution of drone images using a rotary wing by comparing them with field measurement results and to analyze stands patterns in actual vegetation map preparation by comparing drone images with aerial images provided by National Geographic Information Institute of Korea. A total of 11 ground control points (GCPs) were selected in the area, and coordinates of the points were identified. In the analysis of aerial images taken by a drone, error per pixel was analyzed to be 0.284 cm. Also, digital elevation model (DEM), digital surface model (DSM), and orthomosaic image were abstracted. When drone images were comparatively analyzed with coordinates of ground control points (GCPs), root mean square error (RMSE) was analyzed as 2.36, 1.37, and 5.15 m in the direction of X, Y, and Z. Because of this error, there were some differences in locations between images edited after field measurement and images edited without field measurement. Also, drone images taken in the stream and the forest and 51 and 25 cm resolution aerial images provided by the National Geographic Information Institute of Korea were compared to identify stands patterns. To have a standard to classify polygons according to each aerial image, image analysis software (eCognition) was used. As a result, it was analyzed that drone images made more precise polygons than 51 and 25 cm resolution images provided by the National Geographic Information Institute of Korea. Therefore, if we utilize drones appropriately according to characteristics of subject, we can have advantages in vegetation change survey and general monitoring survey as it can acquire detailed information and can take images continuously.

• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.12
• /
• pp.1196-1203
• /
• 2014

Recently, UFRs (Unmanned Flying Robots) have begun to be utilized in various areas for civilian and military applications. Due to this increased utilization, accidents involving UFRsare also increasing. To prevent or monitor accidents caused by UFRs, high-accuracy positioning information is one of the most important technical elements. This paper proposes an efficient UFR monitoring system which provides accurate UFR positioning information with low-cost onboard elements; a small ARM module based on an embedded Linux operating system, a low-cost single frequency GPS receiver with a cheap patch antenna, and a versatile wireless network interface module. The ground monitoring system employs a dual frequency GPS receiver to generate exact UFR coordinates with cm-level accuracy. By processing the UFR measurements based on the Inverse RTK (Real Time Kinematic) method, the ground monitoring system determines the cm-level accurate coordinates of the UFR. The feasibility of the proposed UFR monitoring system was evaluated by three experiments in terms of data loss and accuracy.

• Journal of the Korean earth science society
• /
• v.39 no.1
• /
• pp.46-52
• /
• 2018

This paper is to study the development of three dimensional Digital Surface Model (DSM) using photogrammetry technique based on self-developed Drone (Unmanned Aerial Vehicle (UAV)). To develop DSM, we selected a study area in Jeju island and took 24 pictures from the drone. The three dimensional coordinates of the photos were made by Differential Global Positioning System (DGPS) surveying with 10 ground control points (GCP). From the calculated three dimensional coordinates, we produced orthographic image and DSM. The accuracy of DSM was calculated using three GCPs. The average accuracy of X and Y was from 8.8 to 14.7 cm, and the accuracy of Z was 0.8 to 12.4 cm. The accuracy was less than the reference accuracy of 1/1,000 digital map provided by National Geographic Information Institute (NGII). From the results, we found that the self-developed drone and the photogrammetry technique are a useful tool to make DSM and digital map of Jeju.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.9 no.2
• /
• pp.93-102
• /
• 1991

This study aims to develop techniques for generating Digital Elevation Model(DEM) from SPOT Computer Compatible Tape(CCT) data, so as to present an effective way of generation of DEM for large area. As the first phase of extracting ground heights from SPOT stereo digital data, the bundle adjustment technique was used to determine the satellite exterior orientation parameters. Because SPOT data has the characteristics of multiple perspective projection, exterior orientation Parameters were modelled as a function of scan lines. In the second phase, a normalized cross correlation matching technique was applied to search for the conjugate pixels ill stereo pairs. The preliminary study showed that the matching window size of 13$\times$13 was adequate. After image coordinates of the conjugate pixels were determined by the matching technique, the ground coordinates of the corresponding pixels were calculated by the space intersection method. Then DEM was generated by interpolations. In addtion an algorithm for the elimination of abnormal elevation was developed and applied. The algorithm was very effective to improve the accuracy of the generated DEM.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.27 no.2
• /
• pp.249-260
• /
• 2009

The georeferencing accuracy of the sensory data acquired by an aerial monitoring system heavily depends on the performance of the GPS/IMU mounted on the system. The employment of a high performance but expensive GPS/IMU unit causes to increase the developmental cost of the overall system. In this study, we simulate the images and GPS/IMU data acquired by an UAV-based aerial monitoring system using an inexpensive integrated GPS/IMU of a MEMS type, and perform the image georeferencing by applying the aerial triangulation to the simulated sensory data without any GCP. The image georeferencing results are then analyzed to assess the accuracy of the estimated exterior orientation parameters of the images and ground points coordinates. The analysis indicates that the RMSEs of the exterior orientation parameters and ground point coordinates is significantly decreased by about 90% in comparison with those resulted from the direct georeferencing without the aerial triangulation. From this study, we confirmed the high possibility to develop a low-cost real-time aerial monitoring system.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.4
• /
• pp.471-480
• /
• 2018

Accurate target coordinate is very important in military operations especially field artillery's ground-to-ground attack and air-force's air-to-ground attack. DOS(or TAS) is used to acquire target coordinates from long distance. DOS is comprised of LRF and goniometer. LRF measures distance between DOS and target. Goniometer is comprised of azimuth and vertical angular sensors, DMC and internal GPS receiver. DOS must set the position and orientation(finding grid north) before measurement step(target coordinate acquisition). To improve accuracy of target coordinate, VRS RTK and reference point method are proposed in DOS setup step. VRS RTK provides accurate location coordinate with small deviations, providing high accuracy and precision in positioning and orientation. As a result, horizontal coordinate(easting and northing) accuracy is improved from 2.68 mil(C.L. = 0.95) mil to 0.58 mil(C.L. = 0.95).

• Korean Journal of Remote Sensing
• /
• v.28 no.2
• /
• pp.191-202
• /
• 2012

A high resolution satellite imagery such as KOMPSAT-2 includes a material containing rational polynomial coefficient (RPC) for three-dimensional geopositioning. However, image geometries which are calculated from the RPC must have inevitable systematic errors. Thus, it is necessary to correct systematic errors of the RPC using several ground control points (GCPs). In this paper, we propose an efficient method for automatic correction of image geometries using tie points of a stereo pair and the Shuttle Radar Topography Mission (SRTM) Digital Elevation Model (DEM) without GCPs. This method includes four steps: 1) tie points extraction, 2) determination of the ground coordinates of the tie points, 3) refinement of the ground coordinates using SRTM DEM, and 4) RPC adjustment model parameter estimation. We validates the performance of the proposed method using KOMPSAT-2 stereo pair. The root mean square errors (RMSE) achieved from check points (CPs) were about 3.55 m, 9.70 m and 3.58 m in X, Y;and Z directions. This means that we can automatically correct the systematic error of RPC using SRTM DEM.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.24 no.1
• /
• pp.57-64
• /
• 2006

Recently the extraction of building height information has been investigated using remotely sensed image and digital maps. In this study, based on the digital photogrammetry principle and mono imagery method the building height information can be extracted by using relationship between ground coordinates and image coordinates. To evaluate the result the comparison was done with building height from 1:5000 aerial photo. The experiment shows that extraction of building height could be performed using IKONOS single imagery and digital map and it is proved that the building height could be reconstructed within some extent.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2007.04a
• /
• pp.451-454
• /
• 2007

There is an inseparable relation between human race and engineering work. As world developed into highly industrialized society, a diversity of large structures is being built up correspondently to limited topographical circumstance. Though large structures are national establishments which provide us with convenience of life, there are some disastrous possibilities which were never predicted such as ground subsidence and degradation. It is very difficult to analyze the volume of total metamorphosis with the relative displacement measurement system which is now used and it is impossible to know whether there is structural metamorphosis within a permissible range of design or not. In this research with an object of 13-year-old earthen dam, through generating point-cloud which has 3D spatial coordinates(x, y, z) of this dam by means of 3D Laser Scanning, we can get real configuration data of slanting surface of this dam with this method of getting a number of 3D spatial coordinates(x, y, z). It gives 3D spatial model to us and we can get various information of this dam such as the distance of slanting surface of dam, dimensions and cubic volume. It can be made full use of as important source material of reinforcement and maintenance works to detect previously the bulging of the dam through this research.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2007.04a
• /
• pp.149-152
• /
• 2007

The horizontal geo-location accuracy of KOMPSAT-2, without GCPs (Ground Control Points) is 80 meters CE90 for monoscopic image of up to 26 degrees off-nadir angle, after processing including POD (Precise Orbit Determination), PAD(Precise Attitude Determination) and AOCS (Attitude and Orbit Control Subsystem) sensor calibration. In case of multiple stereo images, without GCPs, the vertical geometric accuracy is less than 22.4 meters LE 90 and the horizontal geometric accuracy is less than 25.4 meters. There are two types of sensor model for KOMPSAT-2, direct sensor model and Rational Function Model (RFM). In general, a sensor model relates object coordinates to image coordinates The major objective of this investigation is to check and verify the geometrical performance when initial KOMPSAT-2 images are employed and briefly introduce the sensor model of KOMPSAT-2.