• Microbiology and Biotechnology Letters
• /
• v.45 no.4
• /
• pp.291-298
• /
• 2017

We compared the ingredients present in freeze-dried ground food samples with those present in hot air-dried and ambient ground food samples to optimize processing conditions for preserving nutrients in and for improving the ingestion of different foods. The freeze-dried ground sample of black bean showed 4.57% higher retention rate than the ambient ground sample of black bean. Mineral content was also significantly different between these two samples. Moreover, the freeze-dried ground sample of black bean contained 11.54% higher content of ${\beta}$-carotene, a precursor of vitamin A, than the ambient ground sample of black bean. Total anthocyanin content was 453.49 mg in the freeze-dried ground sample of Aronia compared with 158.98 mg in the ambient ground sample of Aronia. Contents of ${\beta}$-carotene and niacin increased by 129.47% and 439.39%, respectively, in the freeze-dried ground sample of grapefruit. Retention rates of proteins, carbohydrates, and niacin were 107.74%, 103.87%, and 156.52%, respectively, in the freeze-dried ground sample of germinated brown rice. Protein digestibility increased by 120.5% and 101.14% in the freeze-dried ground samples of Aronia and black bean, respectively, but did not increase in the freeze-dried ground samples of grapefruit and germinated brown rice.

• Korean Journal of Food Science and Technology
• /
• v.40 no.5
• /
• pp.516-521
• /
• 2008

This study was conducted to optimize the analysis condition and quantify the 2-acetyl-1-pyrroline (2AP) in the brown aroma rice. Extraction effect of the solvent for 2AP was the order of ethanol>acetonitrile>methanol in the range from 30 to $90^{\circ}C$. In the extraction time of 15, 30, 60, and 90 min, the 30 min had the highest 2AP concentration, and it was decreased according to lapse of time. At grinding time, 5 sec resulted in highest 2AP concentration. It was recommended that five sec grinding time, using ethanol, at $90^{\circ}C$ for 30 min was the optimization conditions to quantify the 2AP. Hyangmibyeo2ho and Aranghyangchalbyeo were mild aroma. In the foreign aroma rice, 11 of 19 accessions of Indica types and 2 of 6 accessions of Japonica types were more than mild aroma. Finally, 30 accessions of aroma rice were selected based on their 2AP concentration and agronomic traits.

• Journal of the Korea Institute of Building Construction
• /
• v.20 no.1
• /
• pp.1-9
• /
• 2020

Chloride ion, which penetrates into the cement composites from the outside, generally diffuses by the concentration gradient. Chloride ions are adsorbed by the chemical reaction with cement hydrates. Recent studies have shown that anion exchange resin (AER) powder can effectively adsorb the chloride ion in the cement composites, and thus, the cement composites containing AER have a high chloride adsorption capacity and a good resistance for chloride penetration. In this study, the chloride adsorption ability of the AER powder was investigated under the conditions of distilled water and calcium hydroxide saturated solution to determine if the AER powder is less effective to increase the chloride adsorption ability after grinding process. The chloride adsorption ability of AER powder was compared with the previous research about the chloride adsorption of AER bead. In addition, the compressive strength, chloride diffusion coefficient (using NT Build 492 method), and the chloride profile of cement mortar substituted with AER powder were investigated. There was no decrease in the chloride adsorption capacity of AER powder but increase in the kinetic property for chloride adsorption after the grinding process. The AER powder could absorb the chloride ion in the mortar quickly, and showed better chloride ion adsorption ability than the cement hydrates.

• Journal of the Mineralogical Society of Korea
• /
• v.23 no.3
• /
• pp.235-242
• /
• 2010

Froth flotation using the residual water in the end of flotation process has been performed through controlling of pH. IEP (isoelectric point) of molybdenite and quartz in distilled water was below pH 3 and pH 2.7, respectively and the stabilized range was pH 5~10. In case of a suspension in reusing water, zeta potential of molybdenite decreased to below -10 mV or less at over pH 4 due to residual flocculants. As result of pH control, flotation efficiency in the alkaline conditions was deteriorated by flocculation, resulting from expanded polymer chain, ion bridge of the divalent metal cations ($Ca^{2+}$), and hydrophobic interactions between the nonpolar site of polymer/the hydrophobic areas of the particle surfaces. However, the weak acid conditions (pH 5.5~6) improved the efficiency of flotation as hydrogen ions neutralize polymer chains and then weakened its function. In cleans after rougher flotation, the Mo grade of 52.7% and recovery of 90.1% could be successfully obtained under the conditions of 20 g/t kerosene, 50 g/t AF65, 300 g/t $Na_2SiO_3$, pH 5.5 and 2 cleaning times. Hence, we developed a technique which can continuously supply waste water filtered from tailings into the grinding-rougher-cleaning processes.

• Journal of the Korean Ceramic Society
• /
• v.55 no.3
• /
• pp.275-284
• /
• 2018

In the ball milling process of ceramic powders, according to economic considerations for industrial applications, it is very important to quickly determine the optimum process condition with the maximum grinding efficiency. However, it is still difficult to determine the optimum condition for a ball mill with respect to the various process parameters, such as the rotational speed and the milling time. Ball milling was carried out at the same starting conditions with given amounts of alumina powders, balls and water, and was conducted slower or faster or a critical rotational speed was just determined by observing the angular position of the slurry in a semi-translucent polyethylene laboratory container. With respect to the different rotational speeds, which were slower or faster than the critical rotational speed, the particle size distribution of the grained powders and the acoustic intensity caused by cascading of the balls led to various behaviors. From the results of the particle size distribution and the acoustic signal analysis in the ball milling, there was one rotational speed that made the finest milled powder with maximum acoustic intensity. As a result, there was a correlation between the ground particle size and the acoustic intensity, which yields the interpretation that it can be possible in-situ to determine the optimum condition of ball milling by acoustic signal without repeated measurement efforts.

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.3
• /
• pp.293-305
• /
• 2005

Statement of problems. Conventional feldspathic porcelain is used extensively as a restorative material and it is subjected to grinding and polishing during fabrication and delivery procedures. There is still considerable controversy concerning the best methods to achieve the strongest porcelain restorations after such adjustments. Purpose. The objective of this study was to investigate the effects of (1) overglazing, (2) selfglazing, and (3) fine polishing on the flexural strength and fracture toughness of feldspathic dental porcelain. Material and method. Ninety porcelain disks were prepared for flexural strength test and sixty porcelain disks were fabricated for fracture toughness test. Specimens were divided into three groups for each test as follows: 1) overglazed 2) self-glazed 3) polished. The flexural strength of feldspathic porcelains was determined by ring-on-ring biaxial flexural strength test. The fracture toughness values of three experimental groups were obtained by indentation fracture toughness test. Results. The flexural strength of overglazed group was significantly higher than that of selfglazed and polished group (P<0.05), while the difference between self-glazed and polished group was not significant (P>0.05). The fracture toughness values of overglazed and polished group were significantly higher than that of self-glazed group (P<0.05), while the difference between overglazed and polished group was not significant (P>0.05). Conclusions. This results supported the use of polishing as an alternative to glazing metal ceramic restorations, as it was not detrimental in flexural strength and fracture toughness. But, under the conditions of this study, overglazing was the ideal surface finishing method of feldspathic dental porcelain.

• Journal of Welding and Joining
• /
• v.34 no.1
• /
• pp.41-46
• /
• 2016

With the recent increase in size of ships and offshore structures, there are more demand for thicker plates. As the thickness increases, it is known that fatigue life of the structures decrease. To improve the fatigue life, post weld treatments techniques, such as toe grinding, TIG dressing and hammer peening, are typically employed. However, these techniques require additional construction time and production cost. Therefore, it is of crucial interest steels with longer fatigue crack growth life compared to conventional steels. This study investigates fatigue crack growth rate (FCGR) behaviours of conventional EH36 steel and Ferrite-Bainite dual phase EH36 steel (F-B steel). F-B steel is known to have improved fatigue performance associated with the existence of two different phases. Ferrite-Bainite dual phase microstructures are obtained by special thermo mechanical control process (TMCP). FCGR behaviours are investigated by a series of constant stress-controlled FCGR tests. Considering all test conditions (ambient, low temperature, high stress ratio), it is shown that FCGR of F-B steel is slower than that of conventional EH36 steel. From the tensile tests and impact tests, F-B steel exhibits higher values of strength and impact energy leading to slower FCGR.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.9
• /
• pp.1078-1085
• /
• 2011

Prediction of a minimum crack size for growth, which is defined as a crack size that grows fast enough to keep ahead of its removal by contact wear and periodic grinding, is the most demanding work to prevent rail from fatigue failure and develop cost effective railway maintenance strategy In this study, we investigated the wheel load increment due to a rail defect during a train ran over it, and its effect on the minimum crack size for growth. For this purpose, we developed simulation software based on the Fletcher and Kapoor's "2.5D" model and measured wheel load increment during a train passed over a defect. A maximum contact pressure and contact patch size were calculated by 3D FEM and crack growth analyses were performed by varying two of dominant contact contributors; surface friction coefficient(0.1, 0.2, 0.3 and 0.4) and crack aspect ratio. The minimum crack sizes for growth were calculated from 0.29 to 1.44mm depending on the contact conditions. They were decreasing with increasing surface friction coefficient and decreasing with crack aspect ratio(a/b).

• Journal of the Korean Society of Industry Convergence
• /
• v.14 no.2
• /
• pp.45-52
• /
• 2011

Since the most exclusive machines of the modern industries which require the nano precision rates are evolved from the machine tools, the design of the stable machine tool structure is very critical. Exclusive machines for the modern industries such as semiconductor, solar cell and LED have surface machining processes which are similar to the face cutting and grinding of conventional machine tools. This study was initiated to stabilize a milling machine structure and further to help design those exclusive machines which have similar machining mechanisms. The vibrations inherent to the machine tool structures hurt the precision machining as well as damage the longevity of the structures. There have been numerous researches in order to suppress the vibrations of machine tool structures using the extra modules such as actuators and dampers. In this paper, the dynamic properties are analyzed to obtain the natural frequencies and mode shapes of a machine tool structure which reflect the main reasons of the biggest vibrations under the given operating conditions. And the feasibility of improving the stability of the structure without using any additional apparatus has been investigated with minor design changes. The result of the study shows that simple changes based on proper system identification can considerably improve the stability of the machine tool structure.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.14 no.1
• /
• pp.79-91
• /
• 2012

A curved fiber reinforced polymer (FRP) panel is produced with a certain width depending on allowances of manufacturing processes and facilities. An targeted arch-shaped structure could be built by sequential connection of series of the FRP panels. The connection manner between the FRP panels could be given by chemical treatment, mechanical treatment and hybrid method. Among those, the connection between the panels by chemical treatment is commonly adopted. Therefore, For an optimized design of the connected part between FRP pannels, a number of direct shear tests have been undertaken in terms of a number of parameters: surface treatment conditions, bonding materials, etc.. As results, surface grinding condition by sand paper or surface treatment by sand blasting appear properly acceptable methods, and epoxy and acryl resins are shown to be effective bonding materials for the purpose in this study.