• Nuclear Engineering and Technology
• /
• v.25 no.3
• /
• pp.381-393
• /
• 1993

This paper presents the experimental results on flooding of countercurrent flow in vertical multirod channels, which consists of falling water film and upward air flow. In particular, the effects of spacer grids, with and without mixing vane, and of blockage in the multirod bundle on the behaviour of flooding were investigated. The 5$\times$5 zircaloy tube bundle was used for the test section. The comparison of previous analytical models and empirical correlations with present data on flooding showed that the existing models and correlations predict much higher flooding curves. The spacer grid causes the lower flooding air flow rate to compare with the bare rod bundle. However, the mixing spacer grids need a higher flooding air flow rate for a constant liquid flow rate than the spacer grids without mixing vanes. The bundle containing blockages has the highest flooding air flow rate among the bundles with spacer grids and blockages. Empirical flooding correlations for the three types of test section have been made.

• Journal of the Korean Geosynthetics Society
• /
• v.3 no.4
• /
• pp.41-48
• /
• 2004

Recently a method for increasing the bearing capacity by laying the reinforcing materials with three or four layers as a method reinforcing the ground was studied recently. The purpose of this study is to examine the method for increasing shear-strength factor of the ground by reinforcing the ground under the foundation. According a method of wrapping ground with bakk-shape or semicircle-shape by geotextile was developed in this study and it looks likes anaspect that spreading footing exits under spread footing. A simulation loading-test using Aluminum sticks was carried out in order to examine the mechanism about bearing capacity of spread footing reinforced by geotextile. Increase of ultimate bearing capacity was verified in this simulation loading-test when charging loads to spread footing, which is propose from this study, reinforced by geotextile. And moving directions of points of the ground were also checked by grid-type indication method, and the areas where plastic failure appeared were checked by B-shutter photographing.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.25-32
• /
• 2013

PURPOSES : The purpose of this study is to provide the method of how to measure the coefficient of thermal expansion of concrete using temperature compensation principle of electrical resistance strain gauge. METHODS : The gauge factor compensation method and thermal output(temperature-induced apparent strain) correction method of self-temperature compensation gauge were investigated. From the literature review, coefficient of thermal expansion measurement method based on the thermal output differential comparison between reference material(invar) and unknown material(concrete) was suggested. RESULTS : Thermal output is caused by two reasons; first the electrical resistivity of the grid conductor is changed by temperature variation and the second contribution is due to the differential thermal expansion between gauge and the test material. Invar was selected as a reference material and it's coefficient of thermal expansion was measured as $2.12{\times}10^{-6}m/m/^{\circ}C$. by KS M ISO 11359-2. The reliability of the suggested measurement method was evaluated by the thermal output measurement of invar and mild steel. Finally coefficient of thermal expansion of concrete material for pavement was successfully measured as $15.45{\times}10^{-6}m/m/^{\circ}C$. CONCLUSIONS : The coefficient of thermal expansion measurement method using thermal output differential between invar and unknown concrete material was evaluated by theoretical and experimental aspects. Based on the test results, the proposed method is considered to be reasonable to apply for coefficient of thermal expansion measurement.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.28 no.3
• /
• pp.273-282
• /
• 2018

Objectives: Dustiness of nanomaterials is considered as exposure index of essential material. Research on dustiness of nanomaterial is needed to control exposure in workplaces. Method: Dustiness measurement using vortex shaker were installed in the laboratory. Nanomaterials, 1 g, was put in the glass test tube and shaked using vortex shaker. Aerosol dispersed was measured using scanning mobility particle sizer(SMPS) and optical particle counter(OPC). Mass concentration using PVC filter and cassette was measured and TEM grid sampling was conducted. Total particle concentration and size distribution were calculated. Image and chemical composition of particles in the air were observed using transmission electron microscopy and energy dispersive X-ray spectrometer. Eleven different test nanomaterials were used in the study. Results: Rank of mass concentration and particle number concentration were coincided in most cases. Rank of nanomateirals with low concentration were not coincided. Two types of fumed silica had the highest mass concentration and particle number concentration. Indium tin oxide, a mixture of indium oxide and tin oxide, had high mass concentration and particle number concentration. Indium oxide had very low mass concentration and particle number concentration. Agglomeration of nanoparticles in the air were observed in TEM analysis and size distribution. In this study, mass concentration and particle number concentration were coincided and two index can be used together. The range of dustiness in particle number concentration were too wide to measure in one method. Conclusion: Particle number concentration ranged from low concentration to high concentration depend on type of nanomaterial, and varied by preparation and amount of nanomaterial used. Further study is needed to measure dustiness of all nanomaterial as one reference method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.5
• /
• pp.841-852
• /
• 2022

In this paper, a 3-phase inverter output waveform generator based on SPWM control was developed to verify the performance of the LCL filter. In order to obtain a test signal for verifying the performance of the filter, first, a DSP-based 3-phase SPWM signal generation algorithm was developed, and then a three-phase voltage source inverter circuit was designed using three half-bridge gate drivers. Next, one LCL filter was experimentally fabricated to verify the effectiveness of the developed SPWM-based 3-phase inverter output waveform generator as a test signal generator, and a DSP-based performance verification system was experimentally constructed. Finally, by comparing the three-phase voltage waveform before and after the LCL filter obtained in the output control experiment with the given time ratio, the effectiveness of the SPWM-based 3-phase inverter output waveform generator was verified.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.2
• /
• pp.135-145
• /
• 2023

Developing high-fidelity Computational Fluid Dynamics (CFD) simulation methods used to evaluate the airwake characteristics along a flight deck of a large ship, the various kind of data such as actual ship measurement and wind tunnel results are required to verify the accuracy of CFD simulation. Inflow velocity profile at the bow, local unsteady flow field data around the flight deck, and highly reliable wind tunnel data which were measured after reviewing Atmospheric Boundary Layer (ABL) simulation and Reynolds Number effects were also used to determine the key parameters such as turbulence model, time resolution and accuracy, grid resolution and type, inflow condition, domain size, simulation length, and so on in STAR CCM⁺. Velocity ratio and turbulent intensity difference between Full-scale CFD and actual ship measurement at the measurement points show less than 2% and 1.7% respectively. And differences in velocity ratio and turbulence intensity between wind tunnel test and small-scale CFD are both less than 2.2%. Based upon this fact, the selected parameters in CFD simulation are highly reliable for a specific wind condition.

• The Journal of Korean Physical Therapy
• /
• v.35 no.4
• /
• pp.89-94
• /
• 2023

Purpose: This study investigates the impact of self-myofascial release using a foam roller on the quadriceps femoris for pelvic stability. We further compare the effects of a GRID surface Foam Roller (GFR), a Non-Vibration Foam Roller (NVFR), and a Vibration Foam Roller (VFR). Methods: Thirty healthy adults (15 males, 15 females) participated in this study and were randomly assigned to one of three conditions: GFR, NVFR, or VFR. Participants walked at self-selected speeds with an arm sling before and after foam roller stretching. The analyzed gait parameters included pelvic tilt, pelvic obliquity, and pelvic rotation. Results: In the NVFR and VFR groups, there was a Significant differences were obtained in the pelvic tilt between pre-test and post-test values (p<0.05) in the NVFR and VFR groups, but no significant difference was observed in the GFR group (p>0.05). Comparing the amount of change between the three groups exhibited a significant decrease in pelvic tilt in the NVFR and VFR groups compared to the GFR group (p<0.017). No significant differences were found in pelvic obliquity and pelvic rotation (p>0.05) in all groups. Conclusion: While walking, the use of a VFR for self-myofascial release results in pelvic alteration by reducing the anterior pelvic tilt. We propose that a foam roller can be utilized to enhance pelvic stability during gait.

• Transactions of the Korean hydrogen and new energy society
• /
• v.34 no.4
• /
• pp.334-341
• /
• 2023

The purity of hydrogen finally purified in the hydrogen purification process system is greatly influenced by the uniformity of the purification temperature of the dry tower. A in-house code that can be easily used by field designers has been developed to predict the capacity of the appropriate heat source and the time to reach the temperature of the dry tower. A code was developed to predict unsteady heat transfer using Visual Basic for Applications. To verify the developed code, a grid independence test was performed, and finally, calculations were performed for two cases. In the first case, the time for the temperature of the heater jacket to reach 360℃ was about 1,400 seconds when the supply heat source was 1,000 W. And in the second case, the time for the temperature of the heater jacket to reach 360℃ was about 710 seconds when the supply heat source was 2,000 W. It was confirmed that the developed code well describes the actual test data of the regeneration process of adsorption and desorption, and it is judged that the code developed in the design process of various capacity systems will be effectively applied to the heat capacity calculation in the future.

• Physical Therapy Rehabilitation Science
• /
• v.12 no.2
• /
• pp.92-104
• /
• 2023

Objective: The purpose of this study was to investigate the effect of spinal mobilization with leg movement (SMWLM) and neural mobilization (NM) in patients with lumbar disc herniation (LDH) accompanied by radiating pain. Design: Three-group pre-test-post-test control group design. Methods: We enrolled 48 participants, whom we randomly assigned to three groups. The SMWLM group (n=16) underwent 20 min of conventional physical therapy (CT) and 20 min of SMWLM. The NM group (n=16) underwent 20 min of CT and 20 min of NM. The control group (n=16) underwent 20 min of CT. These interventions in all the groups were performed three times a week for 4 weeks. Numeric pain rating score (NPRS), body grid chart score (BGCS), passive straight leg raise (PSLR), active lumbar flexion range of motion (ALFROM), korean version oswestry disability index (KODI), and korean version fear avoidance beliefs questionnaire (KFABQ) were measured pre- and post-intervention. Results: In all three groups, the NPRS, PSLR, KODI, and KFABQ scores were significantly different pre- and post-intervention (p<0.05). Significant differences were observed in BGCS and ALFROM in the SMWLM and NM groups pre- and post-intervention (p<0.05). The SMWLM group showed more improvement in the NPRS of leg pain, ALFROM, and KFABQ score than that exhibited by the NM and control groups (p<0.05). Conclusions: Both SMWLM and NM were effective for improving back and leg pain, centralization of symptoms, mechanical sensitivity, lumbar mobility, lumbar functional disability, and psychosocial functioning in patients with LDH with radiating pain.

• Journal of Soil and Groundwater Environment
• /
• v.28 no.5
• /
• pp.1-11
• /
• 2023

The phenomenon of sediment resuspension in rivers and lakes causes contaminants (heavy metals and nutrients) accumulated in the sediment to leach into the overlying water. As a result, it can lead to changes in toxic effects and eutrophication in the aquatic ecosystem. In this regard, it is important to quantitatively determine the amount of contaminants leached during sediment resuspension. In this study, methods for assessing the amount of released contaminants and the types of contaminants potentially released due to sediment resuspension were studied and summarized. Methods for assessing leaching can be divided into three groups based on the principle of causing resuspension: (i) the oscillating grid chamber method, (ii) the mechanical stirrer method, and (iii) the shaker method. It was confirmed that the types of contaminants that can potentially be released include heavy metals bound to sulfides, as well as exchangeable and labile forms of heavy metals and nutrients. To effectively manage stable aquatic ecosystems in the future, a simplified leaching test method is needed to assess in advance the risks (i.e., changes in toxic effects and eutrophication) that sediment resuspension may pose to aquatic ecosystems.