• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.673-676
• /
• 1999

We fabricated green sheet by tape casting method with fluormica glass-ceramic powders for fabrication of low temperature co-firing substrate. After ball milling with organic additives, we investigated green strength and density of green sheets which were casted by doctor blade machine. Green sheets were sintered at 700 ~ 1,00$0^{\circ}C$ for 1 ~3hrs. Microstructure, linear shrinkage and dielectric constant of substrates were surveyed.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2007.11a
• /
• pp.71.1-71.1
• /
• 2007

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.11a
• /
• pp.65-65
• /
• 1999

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1112-1117
• /
• 2006

The properties of LTCC green tape with addition of binder were investigated in order to understand an effects of binder on multilayer processing. A green sheet form was fabricated through tape casting method with the MLS-22 powder. The lamination density increased with increasing amount of binder and lamination pressure. With increasing amount of binder, the elongation of ceramic sheets increased but the tensile stress and air-permeability decreased. The addition of excessive binder is caused defects in the green sheet during via hole punching. The optimum condition of the via hole without defects was observed from amount of the binder 10 wt%.

• Journal of the Korean Ceramic Society
• /
• v.43 no.9 s.292
• /
• pp.519-526
• /
• 2006

A full-factorial design of experiments with three input factors and two levels for each factor including center points was utilized for the preparation and characterization of twelve types of $BaTiO_3$ slips for tape casting. Ceramic powders with different particle sizes, different milling methods such as high energy milling and conventional ball milling, and two types of dispersant with different polymeric species were chosen as input factors in order to investigate their effects on slip and on green tape properties. Tape casting, a small rectangular-shaped K-square preparation, characterization and quantitative data analysis using statistical software were followed. Ceramic powder was the most significant among three input factors for the output responses of slip viscosity and green tape density, showing more favorable results with large particles than with very fine ones. In addition, high energy milling for only 30 min was more efficient than 24h of conventional ball milling in terms of powder dispersion and milling. The optimum condition based on the experimental results was a slip exposed to high energy milling with large ceramic particles along with a methylethyl acetate dispersant.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.784-787
• /
• 2003

In this study, water jet etching of aqueous green tape was attempted for processing barrier rib of plasma display panel. This process combines 1) chemical etching between water and aqueous based binder in the tape and 2) mechanical erosion by water jet. Effects of etching parameters such as pressure, temperature and aqueous binder content on the morphology of barrier ribs formed were investigated. The results demonstrated a possibility of processing barrier ribs by water jet etching.

• Journal of the Korean Ceramic Society
• /
• v.37 no.1
• /
• pp.57-62
• /
• 2000

In this study, an attempt was made to demonstrate the possibility of using laser scribing method in manufacturing the barrier ribs of plasma display panel. The scribing with a CO2 laser was conducted on the green tape produced by the doctor blade tape casting method. Among the processing parameters, the quenching gas pressure, shape of mask, and laser power were found to affect the depth and angle of the scibed barrier ribs.

• Proceedings of the KIEE Conference
• /
• 1999.11b
• /
• pp.446-449
• /
• 1999

본 연구에서는 기존의 자성 웨지의 제조공정을 대체하여 제조 공정이 단순하고, 그의 정밀성이 우수한 tape casting-lamination법에 의한 자성 웨지의 제조 공정의 적용 가능성에 대한 연구를 수행하였다. 철 분말과 에폭시 slurry는 우수한 tape casting 특성을 보여주었으며, 이렇게 얻어진 green tape과 유리 섬유를 적층하여 자성 웨지를 얻었다. 이러한 과정을 거쳐서 얻어진 제품의 품질 특성을 평가한 결과, 기존의 제조 공정으로 얻어진 제품에 비하여 품질의 균일성이 우수하며, 제조 공정을 혁신적으로 단축하는 것이 가능한 것을 보여주고 있다.

• Journal of the Korean Ceramic Society
• /
• v.34 no.11
• /
• pp.1173-1181
• /
• 1997

Effects of particle size distribution of alumina ceramics on behaviors of tape casting were investigated with emphases on the rheological characteristic of slurry, green density, green sheet strength, and sintering density. For the control of particle size distribution of alumina, the commercial grade low soda alumina, which had different mean particle size of 3.58 ${\mu}{\textrm}{m}$ and 0.42 ${\mu}{\textrm}{m}$, were chosen and blended together. As results, the mixing of 80 wt% fine powder and 20 wt% coarse powder(designated to FC20) led to the increase of packing density and strength of green sheet, and made it easy to handle during processing without lowering of sintering density. Besides, the pseudoplastic behavior of slurry decreased with increase of the fraction of coarse alumina powder.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1136-1141
• /
• 2003

Among various methods to manufacture the PDP barrier ribs, the pressing and the roll forming methods are simple and economical because they form the ribs by utilizing the plastic flow of the green tape in a relatively short time without generating air-polluting dusts. In the present study, the roll forming method was investigated by experiments as well as numerical analyses and in result the groove roll and the preform were designed. The effect of draft angle, comer radius, and initial thickness of the green tape on the plastic flow was examined by a series of parametric studies. The preform was recommended to ease the plastic flow into the grooves and to avoid the occurrence of crack during rolling and sintering processes.