• Resources Recycling
• /
• v.12 no.2
• /
• pp.11-20
• /
• 2003

Limestone mine waste was used as a aggregate far permeable concrete. Void ratio, continuous void ratio, coefficient of permeability, compressive strength and flexural strength of concrete were measured and then the relationship between porosity and strength properties was investigated. Void ratio, continuous void ratio and strength properties of permeable concrete were greatly influenced by the grain size of aggregate and void filling ratio in comparison with the containing ratio of limestone mine waste. Furthermore, void ratio showed a good relation with continuous void ratio, and porosity of permeable concrete indicated a good relation with strength properties also. The coefficient of permeability of permeable concrete using limestone waste was over 0.2 cm/sec and was excellent result in comparison with normal concrete. Therefore, it could be expected that the limestone mine waste would be utilized as aggregate for pavement concrete, green concrete and water resource specie concrete in the results of this study.

• Advances in aircraft and spacecraft science
• /
• v.4 no.3
• /
• pp.281-296
• /
• 2017

The axial-injection end-burning hybrid rocket proposed twenty years ago by the authors recently recaptured the attention of researchers for its virtues such as no ${\zeta}$ (oxidizer to fuel mass ratio) shift during firing and good throttling characteristics. This paper is the first report verifying these virtues using a laboratory scale motor. There are several requirements for realizing this type of hybrid rocket: 1) high fuel filling rate for obtaining an optimal ${\zeta}$; 2) small port intervals for increasing port merging rate; 3) ports arrayed across the entire fuel section. Because these requirements could not be satisfied by common manufacturing methods, no previous researchers have conducted experiments with this kind of hybrid rocket. Recent advances in high accuracy 3D printing now allow for fuel to be produced that meets these three requirements. The fuel grains used in this study were produced by a high precision light polymerized 3D printer. Each grain consisted of an array of 0.3 mm diameter ports for a fuel filling rate of 98% .The authors conducted several firing tests with various oxidizer mass flow rates and chamber pressures, and analysed the results, including ${\zeta}$ history, using a new reconstruction technique. The results show that ${\zeta}$ remains almost constant throughout tests of varying oxidizer mass flow rates, and that regression rate in the axial direction is a nearly linear function of chamber pressure with a pressure exponent of 0.996.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.65 no.4
• /
• pp.264-273
• /
• 2020

'Ilpum', a Korean short-grain mid-late maturing rice cultivar, was developed in 1990, more than 30 years ago. Despite its age, it has been the most widely grown cultivar in the Gyeongbuk province of South Korea for more than 25 years, making it the most important rice cultivar for the people of the Gyeongbuk province. The aim of this study was to analyze the relationship between the rice yield of "Ilpum', the main rice cultivar in the Gyeongbuk province, and climate elements in the Daegu (southern plain area) and the Andong (inland mountainous area) regions in Gyeongbuk, South Korea. The rice yield over the past five years increased by about 13% and 24%, compared to that produced in the late 1990s in Daegu and the early 2000s in the Andong region, respectively. The number of panicles per hill and the grain ripening rate significantly affected rice yield in the 'Ilpum' cultivars in the Daegu region. The faster heading was a factor in the increase in 'Ilpum' rice yield in the Andong region. The air temperature has been rising and sunshine duration has been increasing from the late 1990s to present in both regions. Rice yield was evaluated to understand the effect of climate factors. The rice yields increased owing to the long sunshine duration during the grain-filling stage in both regions. In Andong, increasing the maximum temperature during the vegetative stage increased rice yield. Rising air temperature during the reproductive stage also increased rice yield. In particular, long sunshine hours throughout the whole rice growing period increased the rice yield of this cultivar in the Andong region.

• Korean Journal of Breeding Science
• /
• v.42 no.4
• /
• pp.407-412
• /
• 2010

Recently, peoples are greatly concerned with global temperature change because global warming can be a potential serious effect on agriculture production such as yield reduction and poor grain quality. On the other hand, it can bring some beneficial effects through twice cultivation of rice in temperate region. In order to overcome this situation, we developed extremely early-maturing rice 'Milyang255' which heading date was similar with 'Jinbuolbyeo'. Based on agronomic characteristics of 'Milyang255', it has very short stature as 65 cm of culm length and slightly lower spikelets number per panicle compared with that of 'Jinbuolbyeo'. However, the grain appearance, palatability and other items were better than those of 'Jinbuolbyeo' in panel test of cooked rice. The milled rice yield of 'Milyang255' is 3.94 MT/ha at the early transplanting. Especially, its grain filling rate was higher and faster than Jinbuolbyeo and the head rice ratio in milled rice was also higher. Thus, 'Milyang255' can efficiently reduce the growth duration of rice cultivation and also be useful material for research on twice cultivation of rice in Korea.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.1
• /
• pp.92-97
• /
• 1994

The reports on the chemical composition of developing job's tears seeds is very insufficient by this time. The purpose of this study was to obtain the fundamental information on chemical component of the developing job's tears seed, including starch, sugar, oil, protein, fatty acid, Alkali Digestibility Value(ADV), 100-grain weight. Two job's tears varieties in different by maturity types were analyzed for those components from 10 days after heading to maturity, with 5-day intervals. Total sugar content in seeds followed a pattern of linear increase after heading, but it started to decreased around 15 days after heading. On the other hand, starch content continued to increased until maturity and the highest increasing occurred between 15 and 20 days after heading. The protein content of seeds was decreased, while oil content was increased through the ripening process. Starch content showed a positive correlation with 100-grain weight, ADV, oil and germination percent, but it had negative correlation between total sugar and protein contents in ripening process. Maximum starch content, 100 grain weight, and germination percent obtained by quadratic equation were attained 38 to 43 days after heading. So that the physiological maturity of job's tears seeds was considered to be 40 days after heading.

• Korean Journal of Soil Science and Fertilizer
• /
• v.6 no.2
• /
• pp.107-113
• /
• 1973

A pot experiment on paddy rice was carried out to investigate the effect of temperature after heading with application of phosphate, potash and silica on the yield and nutrient uptake. The results obtained are as follows: 1. The Grain yield was greatly affected by temperature during ripening. The yield at $20^{\circ}C$ and at $15^{\circ}C$ decreased to 62.3% and to 37.2% of that at $25^{\circ}C$ respectively. However, the application of phosphate, potash and silica at transplanting increased the grain yield even at low temperature of $15^{\circ}C$. 2. Percentage of ripened grain and weight of 1,000 grains decreased with decreasing temperature but they were increased by the application of phosphate, potash and silica at the low temperature of $15^{\circ}C$. 3. The grain filling rate was fast in the early stage of ripening at high temperature while it was fast in the later stage at low temperature. Low temperature damage was severe in the early stage of ripening. 4. Accumulation of carbohydrate in the grain was small at low temperature of $15^{\circ}C$ and the application of phosphate, potash and silica was effective to increase carbohydrate content in the grain at low temperature. 5. The content of T-N and $P_2O_5$ in straw grown at low temperature were high whereaas those of $K_2O$ and $SiO_2$ were low which were increased by the application of potash and silica. 6. There was a positive correlation between the grain yield and rate of ripening, 1,000 grain weight, contents of $K_2O$ and $SiO_2$, $K_2O/N$ and $SiO_2/N$ ratio, but a negative correlation between grain yield and contents of T-N and $P_2O_5$ in the straw at harvesting stage. 7. Ripening rate and weight of 1,000 grains showed a significant positive correlation with $K_2O$, $SiO_2$, $K_2O/N$ and $SiO_2/N$ ratio in the straw. Further, there was a negative correlation between ripening rate and the contents of T-N and $P_2O_5$ but a positive correlation between weight of 1,000 grains and these elements.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.4
• /
• pp.69-83
• /
• 1999

The permeability of converter slag, replacing material of sand mat on improving soft clay foundation, was evaluated in the laboratory. The effects of grain size, flow water time and aging were investigated using sea and fresh water. In the case of converter slag submerged with fresh water, the coefficients of permeability in A and B samples less than 10 mm grain sizes were measured as $6.52\times10^{-2}cm\; per\; sec\; and\; 5.99\times10^{-1}/cm$ per sec respectively, while they were $1.88\times10^{-2}/cm\; per\; sec,\; 3.86\times10^{-1}/cm$ per sec respectively under sea water condition. Also, the condition of turbulent flow may exit and was experimentally identified from the relationship between hydraulic gradient and seepage velocity. After 100 days under sea water condition, the coefficients of permeability of A and B samples decreased ten times than initial values. The reduction of permeability coefficient was considered to result from the filling of voids in high-calcium quicklime(CaO).

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.39 no.5
• /
• pp.420-425
• /
• 1994

Soybean seeds deteriorate even before harvest, especially under high temperature and high relative humidity conditions. This study was conducted to determine the effect of harvest date on seed quality in early maturing soybean cultivars. Soybean cultivars used in the experiment were Damyang-native, having small seed with yellow color, and Yuhsuzumi, having large seed with green color. The length of physiological maturity to grain harvest was 24 days in Yuhsuzumi and 8 days in Damyang-native. The moisture contents of seed were 25.3 % in Yuhsuzumi and 14.5 % in Damyang-native cultivar when pod reached its mature pod color. The seed color of Yuhsuzumi started to turn yellow, and its germination rate was greatly decreased when harvest was delayed after maturity, However, Damyang-native cultivars produced seed of high quality regardless of delayed harvest.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.43 no.3
• /
• pp.147-151
• /
• 1998

The conductivity test is a measure of electrolytes leakage from plant tissue. The shorter the maturation period after heading was the greater electrical conductivity (EC) of rice seed. The polymer-coated seed was not different in EC compared with non-coated seed. As soaking time of rice seed increased, EC increased gradually. The EC varied from 9.9 to 20.7$\mu$S $cm^{-1}g^{-l}$ for control plots and from 21.3 to 41.7$\mu$S $cm^{-1}g^{-l}$ for heat-killed seeds which were produced by autoclaving seeds at 121$^{\circ}C$ for 20 minutes. The germination speed (the rate of 5th day) of rice seed was 94% at control plot, 83% at low temperature and 20% at high temperature. Besides, germination percentage was 95% for the control, 92% for the low temperature treatment and 39% for the high temperature treatment. The EC was negatively correlated (r=-0.771$^{**}$) with germination percentage at low temperature. Water uptake in seeds of 30, 40, 50 days after heading (DAH) was greater than that of 20 DAH. Plant height of seedlings was 9.84 cm for the control but 4.32 cm for the high temperature treatment, and the tallest for polymer-coated seed. Dry weight of seedlings was 0.841 g for the control and 0.287 g at high temperature. Besides, the polymer-coated seed was heavier than non-coated seed. The number of roots was largest from 40 to 50 DAH and polymer-coated seed, but was decreased from 20 to 30 DAH. The length of roots was 20.52 cm at control plot and 19.89 cm polymer-coated seed but 8.68 cm for the low temperature treatment and 7.28 cm for the high temperature treatment.

• Journal of Korea Foundry Society
• /
• v.37 no.5
• /
• pp.148-156
• /
• 2017

The effects of minor additives on the casting properties of AC4A aluminum alloys were investigated. Measurements of the cooling curve and microstructure observations were conducted to analyze the effects of Ti-B and Sr minor elements during the solidification process. A fine grain size and an increase in the crystallization temperature for the ${\alpha}-Al$ solution were evident after the addition of 0.1wt% Al-5%Ti-1%B additive. The modification effect of the eutectic $Mg_2Si$ phase with the addition of 0.05% Al-10%Sr additive was prominent. A fine eutectic $Mg_2Si$ phase and a decrease in the growth temperature of the eutectic $Mg_2Si$ phase were evident. Fluidity, shrinkage and solidification-cracking tests were conducted to evaluate the castability of the alloy. The combined addition of Al-5%Ti-1%B and Al-10%Sr additives showed the maximum filling length owing to the effect of the fine ${\alpha}-Al$ grains. The macro-shrinkage ratio increased, while the micro-shrinkage ratio decreased with the combined addition of Al-5%Ti-1%B and Al-10%Sr additives. The macro-shrinkage ratio was nearly identical, while the micro-shrinkage ratio increased with the addition of the Al-10%Sr additive. The tendency of the occurrence of solidification cracking decreased owing to the effect of the fine ${\alpha}-Al$ grains and the modification of the $Mg_2Si$ phase with the combined addition of Al-5%Ti-1%B and Al-10%Sr additives.