The binders introduced in Korea were originally designed to be used for Japonica-type varieties which have relatively long stem and are highly resistant to shattering. In order to use it for Tongil varieties which are short and easy to be shattered, mechanical modifications are necessary to reduce a grain loss incurred during binder operation. This study was intended to investigate analytically and experimentally the major sources of grain losses caused by three kinds of binders now introduced in Korea. Actual modification for each of three binders was done and experimentally compared to see if any improvement on grain loss was achieved. The results obtained in this study are summarized as follows; 1. It was required that the power transmission of binder should have a shifting mechanism so that velocities of pick-up and traveling units could be changed independently as desired according to the Japonica-type and Tongil varieties. In other words, the desired velocity of traveling unit should be obtained by shifting the transmission and the velocity of pick-up unit should be selected by reaping clutch according to the variety independent of the velocity of traveling unit as shown in Fig. 6. 2. To reduce grain loss it was desired that the moving parts of the pick-up unit should have the lowest possible velocities in harvesting Tongil varieties, unless the reduction of the speed be hindered the conveyance of the material. Based on the study, it was concluded that the velocities of pick-up unit be reduced by about 35% of those of the existing units. 3. It was found that the lug at the upper rotating section of pick-up case gave a severe impact on the ears of rice to increase grain loss. The optimum design of pick-up case to protect the ears from the protruding part of the lug was recommended by the result of analysis of the trajectory of the end-point of lug at the position. 4. It was proved analytically and experimentally that pick-up unit at the lower-rotating part was the other important source of grain loss in pick-up and divider assembly. In order to reduce a grain loss incurred by lugs at their lower-rotating section, it was suggested to improve it by (1) widening the space between right and left lower-rotating section, (2) shortening the length of lugs, (3) enlargement of the angle between the pick-up case and ground-level, and (4) attaching guard to right and left dividers so that the rotating lug could not give a high impact to the paddy hill. 5. Pick-up and divider assembly of the original binder of three models studied was modified according to the suggestions that were given by the preliminary study. Field test showed that the modified binders were able to reduce grain losses by about 0.4-0.7 percentage points compared to those without modification.
국내에서 소비지역에 필요한 호밀 종자를 생산하기 위해 경남지역에 적합한 종자 채종기술을 개발하고자 2013~2015년까지 3개년에 걸쳐 경상남도 산청에서 시험을 실시하였다. 품종은 국내 육성종인 곡우호밀을 사용하였고, 시험구는 파종량 3수준(3, 5, 7 kg 10 a-1), 질소시비량 4수준(0, 3, 6, 9 kg 10 a-1)의 분할구배치법 3반복으로 하였으며, 생육특성과 종실 생산성을 평가하였다. 호밀 종자의 파종량을 3 kg 10 a-1로부터 7 kg 10 a-1로 증가시킴에 따라 설립중이 증가하고 임실률과 1 수립수가 감소하였지만 m2당수수가 증가하여 전체 수량이 증가하는 경향이었다. 그리고 유효경비율, 리터중, 1000립중이 다소 감소하였으나 수량에는 영향이 크지 않았다. 질소 시비량을 무비로부터 9 kg 10 a-1로 증가시킴에 따라 출수기가 늦어지고 도복이 다소 증가하지만, m2당수수와 1수립수가 많아져서 수량이 증가하였다. 그리고 호밀의 종실 수량은 파종량과 질소 시비량 간에 교호작용을 보이지 않았다. 호밀의 종실 수량, 파종용 종자 비용과 질소 과잉 시비에 따른 환경오염, 도복 등을 고려할 때 산청지역에서 호밀 종자생산을 위해 적합한 파종량은 5 kg 10 a-1, 질소 시비량은 3 kg 10 a-1로 추천되었다.
Dean's equilibrium beach profile formula was used to investigate the correlation between the static shoreline position and the incident wave energy. The effect of the longshore sediment transport was neglected, and the results showed the reasonable agreement compared with the field observations of Yates et al.(2009), which were conducted for almost 5 years on southern California beaches, USA. The shoreline response varies with the scale factor of Dean's equilibrium beach profile. This implies that the shoreline response could be simply estimated using the sampled grain size without laborious long-term field work. Therefore, the present study results are expected to be practically used for the layout design of submerged or exposed detached breakwaters although the further work is required for performance verification. In addition, after laborous mathematical reviews, the linear relation between incident energy and shoreline response, which was obtained from Yates's field study, yielded a clear mathematical equation showing how the beach slope is related to the grain size.
Amin, A.K.M. Khusrul;Haque, M. Aminul;Akhtaruzzaman, Md;Chowdhury, Nazmun Nahar
한국작물학회지
/
제52권2호
/
pp.134-139
/
2007
The research was conducted with the aim of determining effects of seedling age on the yield of four fine rice varieties viz., Kalizura, Tulshimala, BRRI (Bang-ladesh Rice Research Institute)-37 and BRRI-38. The seedling of different ages such as 15, 25, 35 and 45 days were transplanted on the same day maintaining $25cm{\times}15cm$ spacing. The experiment was laid out in a randomized complete block design with three replications. The yield and yield contributing characters were influenced by seedling age, variety and their interaction. BRRI-38 gave the highest number of effective tillers $hill^{-1}$, panicle length, total spikelets $panicle^{-1}$, grains $panicle^{-1}$, 1000-grains weight and grain yield. Likewise, yield and yield contributing characters were the highest in 35 days old seedling. On the other hand, the variety (BRRI-38) with the same age as of seedlings 35 days old seedlings was found superior to other interactions, but, in the production of grains $panicle^{-1}$ and 1000-grains weight there was no significant effect in this interaction. From the findings it may be inferred that BRRI-38 with 35 days old seedlings produced the highest grain yield.
Magnesium alloys are of emerging interest in the automotive, aerospace and electronic industries due to their light weight, high specific strength, damping capacity, etc. However, practical applications are limited because magnesium alloys have poor formability at room temperature due to the lack of slip systems and the formation of basal texture, both of which characteristics are attributed to the hcp crystal structure. Fortunately, many magnesium alloys, even commercialized AZ or ZK series alloys, exhibit superplastic behavior and show very large tensile ductility, which means that these materials have potential application to superplastic forming (SPF) of magnesium alloy sheets. The SPF technique offers many advantages such as near net shaping, design flexibility, simple process and low die cost. Superplasticity occurs in materials having very small grain sizes of less than $10{\mu}m$ and these small grains in magnesium alloys can be achieved by thermomechanical treatment in conventional rolling or extrusion processes. Moreover, some coarse-grained magnesium alloys are reported to have superplasticity when grain refinement occurs through recrystallization during deformation in the initial stage. This report reviews the characteristics of superplastic magnesium alloys with high-strain rate and coarse grains. Finally, some examples of SPF application are suggested.
This study was intended to develop the mathematical model of the head-fed type threshing unit. As the first step, the physical model of the threshing phenomena was considered to consist of four separate processes as 1) detachment process of grains, 2) movement of grains between the cylinder and concave, 3) grain penetration through stems of bundle, and 4) grain passing through concave. The mathematical and computer models were developed based on the physical models. Threshing experiments were performed and determined the distribution of grain accumulation along the cylinder shaft by varying the moisture content of grains, feeding rate, and cylinder speed. It was found that the model developed coincided very well with the experimental results for the varied operational conditions. Greater concentration of grains passing through concave toward the thresher inlet was equally true for the model and experiment work for the threshing of grains with higher moisture content and with higher cylinder-speed. The model could be used for obtaining the optimized design or for optimizing the performance of the head-fed type threshing unit if term as to power requirement for threshing may be additionally included in the developed model.
본 시험은 육성돈 사료내 건조 맥주박의 급여가 생산성과 영양소 소화율에 미치는 영향을 알아보고자 실시하였다. 시험동물은 3원 교잡종(Landrace${\times}$Yorkshire${\times}$Duroc) 육성돈 48두를 공시하여 42일간 실시하였으며 개시 체중은 19.3 kg 이었다. 시험설계는 1) CON (basal diet), 2) BDG5 (basal diet + 5 % brewer's dried grain) 및 3) BDG10(basal diet + 10% brewer's dried grain)로 3처리로 하여 처리당 8반복 반복당 2마리씩 완전임의배치 하였다. 건조 맥주박의 급여가 육성돈의 생산성에 미치는 영향에 있어서는 일당증체량, 일당사료섭취량 및 사료효율에서 처리구간에 유의적인 차이를 보이지 않았다. 영양소 소화율 중 건물 소화율에 있어서 BDG5 처리구가 CON과 BDG10 처리구와 비교하여 유의적으로 높았다(p<0.05). 질소 소화율에 있어서는 BDG10 처리구가 CON과 BDG5 처리구와 비교하여 유의적으로 가장 높았으며(p<0.05) BDG5 처리구가 CON 처리구와 비교하여 유의적으로 높았다(p<0.05). 또한, 에너지 소화율에서는 BDG5 처리구가 CON 처리구와 비교하여 유의적으로 높았다(P<0.05). 결론적으로, 육성돈 사료내 건조 맥주박의 급여는 성장능력에는 영향을 미치지 않으면서 영양소 소화율을 개선시키는 것으로 나타났다.
The degree of purification and the macrostructure of high purity aluminium were studied through the alternate stirring method in order to improve the nonuniformity of solute concentration in the unidirectional stirring method. The $2^3$ factorial design was done to examine the effects of experimental factors more qualitatively. In the relatively low stirring speed of 1500 rpm with alternate stirring mode, the uniform solute profile and refined grain structure were obtained due to strong washing effect and turbulent fluid flow. It was induced by the transition of the momentum boundary layer by alternation of the stirrer. It was concluded from this study that the alternate stirring mode was more effective to obtain the uniformity of solute even in the stirring speed of 1500 rpm. But the degree of purification decreased below the critical alternating period. When 2N(99.8wt.%) aluminium was used as the starting material the morphology of solid-liquid showed the cellular shape and the columnar grains were inclined to the direction of rotation. This inclined grain growth resulted from the difference of relative velocities of solid and liquid. The inclined angle was increased as the stirring speed increased and solidification proceeded. In the case of 4N aluminium, there was no inclined grain growth and it was confirmed from the macrostructure and SEM work that the morphology of solid-liquid interface was planar. From the factorial design, it was found that the alternate stirring mode showed poorer purification effect than that of unidirectional stirring mode at low speed(500 rpm). In addition, the factor that had the most significant effect on the degree of purification was the stirring speed.
최근 구조물들이 대형화됨으로써 보통 콘크리트를 사용할 경우 강도 및 내구성에 비하여 중량이 크다는 결점으로 인해 콘크리트 구조물의 설계 및 시공의 안정에 제약을 주게 된다. 이러한 결점을 개선하기 위해서는 자중이 작고 강도가 큰 경량콘크리트가 요구되나, 국내에서는 실용화를 위한 연구가 아직 미비한 실정에 있다. 일반적으로 고온에서 소성시켜 제조된 인공골재는 골재가 팽창되어 내부에 무수한 기포를 가지게 된다. 따라서 골재의 크기에 따라 이들의 기포가 경량콘크리트 비중과 강도에 미치는 영향 연구가 필요하다. 본 연구에서는 국내에서 개발된 화력발전소 폐기물과 점토를 고온에서 소성, 팽창시켜 만든 인공경량골재의 입도별 배합설계를 실시하고 실험을 통하여 경량콘크리트의 비중 및 강도변화를 비교 고찰했다. 또한 경량콘크리트의 고강도 발현을 위한 인공경량골재의 최적 입도비를 제안하였다.
본 연구는 저비용 고효율의 일체형 곡물 건조/저장 시스템 개발을 위하여 추진되었다. 저장시스템의 용량과 규격, 배출기구의 설치 조건 및 공전, 자전 등의 운전 조건 그리고 대상 곡물의 비중 등의 다양한 조건에서 정해진 배출속도를 충족시키며 곡물의 선입-선출이 보장되는 균일하강 배출기구를 설계하고자 하였다. 곡물 배출 과정에 대한 육안 관찰이 가능한 장치를 제작하여 기존의 균일 단면형 배출기구에서의 곡물의 배출 거동을 관찰하여 기존 기구의 제한점을 검토하였다. 수학적 해석을 통해 주어진 배출 속도를 비롯한 다양한 조건과 곡물의 균일 하강의 조건을 만족시키는 가변 단면형 배출기구의 단면형상을 설계할 수 있는 일반화된 공식을 유도하였으며, 이를 적용하여 제작된 시작품의 운전을 통해 계산값과의 비교 검증의 연구 과정을 수행하였다. 이를 통해 주어진 다양한 조건을 만족하는 나선형의 가변 단면형 균일하강 배출기구의 단면 형상 설계를 위한 일반화된 수학적 모델을 개발하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.