• Journal of Mechanical Science and Technology
• /
• 제14권7호
• /
• pp.744-751
• /
• 2000

To achieve lower flying height for high areal recording density, the laser zone texturing of the disk needs to be designed to reduce glide height. One problem of the laser bump design is that the regular laser bump pattern often produces glide resonance phenomenon, which leads to failure of the glide height test. However, it was found in this study that glide resonance is an intrinsic problem of the glide head used and resonance phenomenon depends on the type of the head slider, that is, the natural frequency of the slider body. Therefore, higher glide height or glide failure caused by glide resonance does not lead to head/media interface problem in the real drive operating conditions in which the data head is used. Pseudo-random bump pattern greatly reduces the glide resonance. Smaller bump pitch will also help to reduce the glide resonance. However, as bump spacing becomes smaller, glide height will be increased due to increased air pressure developed around the bumps. Lowering bump height is the most effect way to reduce glide avalanche.

• The Journal of Korean Physical Therapy
• /
• 제35권4호
• /
• pp.117-123
• /
• 2023

Purpose: In this study, subjects with femoral anterior glide type were examined to investigate the effects of femoral head anterior glide fixation during active straight leg raise on the strength of the hip flexor in a supine position. Methods: Fifteen subjects participated in this study. All subjects were classified through an evaluation form for femoral anterior glide type (FAGT). The strength of the hip flexor was measured during active straight leg raise test (ASLR test), and compared with and without femoral anterior glide fixation in a supine position. The fixation of the femoral head was achieved as per the therapist's manual guidelines. Paired t-test was applied to compare changes in the strength of the hip flexor according to fixation conditions. The level of statistical significance was set at α=0.05. Results: The strength of the hip flexor was lesser during the ASLR test with fixation compared to without fixation (p=0.007). Conclusion: The strength of the hip flexor decreases with fixation. Results of this study revealed a difference between hip flexor strength, with and without femoral anterior glide fixation during ASLR, in subjects with femoral anterior glide type.

• 대한치과의사협회지
• /
• 제55권10호
• /
• pp.688-694
• /
• 2017

Objectives: This preliminary study compared the effects of glide path establishing instruments prior to substantial root canal preparation. Materials and Methods: Glide path was established by enlargement of the 2nd mesiobuccal root canal of Dentalike by using three kinds of glide path preparation nickel-titanium file; PathFile, One G and ProGlider. The pre- and post-instrumented Dentalikes were weighed in the resolution of 1 / 10mg. In addition, after glide path preparation, torque generated during shaping using the WavoOne file was measured. The data were analyzed by one-way ANOVA and Tukey post-hoc test at a significance level of 95%. Results: The ProGlider had the significantly larger amount of reduced weight than other instrument groups (p < 0.05). There was no significant difference between group of glide path preparation with ProGlider and without glide path preparation in maximum torque and total stress generation during the shaping with WaveOne. Conclusions: Glide path preparation instruments may have different efficiency according to their geometries. The Dentalike artificial teeth were revealed to have discrepancies in the size of root canals by microCT examination. It is impossible to make a meaningful judgment of the results due to the reliability or resolution problem of the root canal size of the artificial tooth selected as the standardized tooth.

• Restorative Dentistry and Endodontics
• /
• 제43권4호
• /
• pp.41.1-41.7
• /
• 2018

Objectives: The purpose of the present study was to compare the mean preparation times and frequency with which Reciproc and Reciproc Blue instruments reached the full working length in mandibular molars, with or without glide path preparation. Materials and Methods: Previously untreated mesiobuccal and mesiolingual canals with completely formed apices were randomly divided into 6 groups (n = 50) depending on the usage of Reciproc (RC; VDW), Reciproc Blue (RC Blue; VDW), C-Pilot (CP; VDW), and R-Pilot (RP; VDW) files: RC, RC Blue, RC + C-Pilot (RC-CP), RC-Blue + C-Pilot (RC Blue-CP), RC+R-Pilot (RC-RP), and RC Blue + R-Pilot (RC Blue-RP). A glide path was prepared using the hand-operated C-Pilot or the machine-operated R-Pilot instruments, respectively. The ${\chi}^2$ test, analysis of variance, and the Tukey post hoc test were used for statistical comparisons. Results: No statistically significant differences were observed in the distribution of the frequency of reaching the full working length in the RC (94%), RC Blue (88%), RC-CP (94%), RC Blue-CP (90%), RC-RP (96%), and RC Blue-RP (92%) groups (p > 0.05). Conclusions: Preparation of a glide path did not have a significant effect on reaching the full working length using these systems.

• Restorative Dentistry and Endodontics
• /
• 제37권4호
• /
• pp.215-219
• /
• 2012

Objectives: The purpose of this study was to investigate the screw-in effect and torque generation depending on the size of glide path during root canal preparation. Materials and Methods: Forty Endo-Training Blocks (REF A 0177, Dentsply Maillefer) were used. They were divided into 4 groups. For groups 1, 2, 3, and 4, the glide path was established with ISO #13 Path File (Dentsply Maillefer), #15 NiTi K-file NITIFLEX (Dentsply Maillefer), modified #16 Path File (equivalent to #18), and #20 NiTi K-file NITIFLEX, respectively. The screw-in force and resultant torque were measured using a custom-made experimental apparatus while canals were instrumented with ProTaper S1 (Dentsply Maillefer) at a constant speed of 300 rpm with an automated pecking motion. A statistical analysis was performed using one-way analysis of variance and the Duncan post hoc comparison test. Results: Group 4 showed lowest screw-in effect ($2.796{\pm}0.134$) among the groups (p < 0.05). Torque was inversely proportional to the glide path of each group. In #20 glide path group, the screw-in effect and torque decreased at the last 1 mm from the apical terminus. However, in the other groups, the decrease of the screw-in effect and torque did not occur in the last 1 mm from the apical terminus. Conclusions: The establishment of a larger glide path before NiTi rotary instrumentation appears to be appropriate for safely shaping the canal. It is recommended to establish #20 glide path with NiTi file when using ProTaper NiTi rotary instruments system safely.

• 한국항공우주학회지
• /
• 제48권9호
• /
• pp.731-743
• /
• 2020

극초음속 활공 비행체는 로켓 부스터에 의해 높은 고도로 올라가서 부스터에서 분리된 후 대기권 내에서 진행 방향을 바꾸면서 약 30~70km 고도에서 마하 5 이상의 극초음속으로 활공한다. 이는 포물선 궤적이 아닌 예측 불가능한 비행경로로 이동하므로 현재 미사일 방어 체계로 요격이 어렵다. 미국은 2010년대 초에 HTV-2와 AHW 비행시험을 수행하여 극초음속 활공 비행 가능성을 확인했고, 최근에 LRHW, ARRW 등 극초음속 활공 비행체 시스템을 개발하고 있다. 중국은 DF-ZF (WU-14) 활공 비행체를 2014년부터 비행시험을 수차례 수행했고 DF-17 미사일에 탑재하여 운용하고 있다. 러시아는 구소련 시절부터 극초음속 활공 비행체 연구를 수행했지만 실패를 거듭했고 근래에 Avangard (Yu-71) 활공 비행체를 SS-19 ICBM에 탑재하여 비행시험에 성공하였다. 본 논문에서는 미국, 중국, 러시아, 일본, 인도, 유럽에서 개발했거나 현재 개발 중인 극초음속 활공 비행체의 특성, 비행시험 사례 및 개발 동향을 고찰하였다.

• Restorative Dentistry and Endodontics
• /
• 제42권4호
• /
• pp.316-323
• /
• 2017

Objectives: This study compared the amount of apically extruded bacteria during the glide-path preparation by using multi-file and single-file glide-path establishing nickel-titanium (NiTi) rotary systems. Materials and Methods: Sixty mandibular first molar teeth were used to prepare the test apparatus. They were decoronated, blocked into glass vials, sterilized in ethylene oxide gas, infected with a pure culture of Enterococcus faecalis, randomly assigned to 5 experimental groups, and then prepared using manual stainless-steel files (group KF) and glide-path establishing NiTi rotary files (group PF with PathFiles, group GF with G-Files, group PG with ProGlider, and group OG with One G). At the end of canal preparation, 0.01 mL NaCl solution was taken from the experimental vials. The suspension was plated on brain heart infusion agar and colonies of bacteria were counted, and the results were given as number of colony-forming units (CFU). Results: The manual instrumentation technique tested in group KF extruded the highest number of bacteria compared to the other 4 groups (p < 0.05). The 4 groups using rotary glide-path establishing instruments extruded similar amounts of bacteria. Conclusions: All glide-path establishment instrument systems tested caused a measurable apical extrusion of bacteria. The manual glide-path preparation showed the highest number of bacteria extruded compared to the other NiTi glide-path establishing instruments.

• 설비공학논문집
• /
• 제15권10호
• /
• pp.852-859
• /
• 2003

R407C is considered as an alternative refrigerant of R22 for air conditioners. An experiment was carried out to investigate the characteristics of the evaporation heat transfer and pressure drop for refrigerant R407C flowing in a fin-and-tube heat exchanger used for commercial air-conditioning unit. The experimental data were useful in analyze the effects of the temperature glide and superheat for R407C. Test were conducted at the conditions of inlet refrigerant evaporation temperature of 7$^{\circ}C$, inlet air relative humidity of 50%, and refrigerant mass fluxes varying from 150 to 250 kg/m$^2$s. Representative results show that the heat exchanger performance for R407C evaporation is significantly affected by the change of the flow pattern from two-phase to super-heated vapor flow.

• Restorative Dentistry and Endodontics
• /
• 제42권4호
• /
• pp.282-289
• /
• 2017

Objectives: It was aimed to compare the cyclic fatigue resistances of ProGlider (PG), One G (OG), and HyFlex EDM (HEDM) nickel titanium glide path files in single- and double-curved artificial canals. Materials and Methods: 40 PG (16/0.02), 40 OG (14/0.03), and 40 HEDM (10/0.05) single-file glide path files were used in the present study. Sixty files were subjected to cyclic fatigue test by using double-curved canals and 60 files by using single-curved canal (n = 20). The number of cycles to fracture (NCF) was calculated and the length of the fractured fragment (FL) was determined by a digital micro-caliper. Twelve pieces of fractured files were examined with scanning electron microscope to determine fracture types of the files (n = 2). The NCF and the FL data were analyzed using one-way analysis of variance and post hoc Tukey test using SPSS 21 software (p < 0.05). Results: In all of the groups, NCF values were significantly lower in double-curved canals when compared to single-curved canals (p < 0.05). For both of single- and double-curved canals, NCF values of HEDM group in apical and coronal curvatures were found to be significantly higher than NCF values of PG and OG groups (p < 0.05). In both of single- and double-curved canals, NCF value of PG group was found significantly higher than OG group (p < 0.05). Conclusions: Within the limitations of this study, HEDM glide path files were found to have the highest cyclic fatigue resistance in both of single- and double-curved canals.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.296-301
• /
• 2004

By the purpose to investigate the change of internal stress and mobile dislocation density in creep, the stress relaxation test is carried out in the condition of each strain. Mobile dislocation density increased until it reached minimum creep rate and after that, it decreased and internal stress didn't have the change approximately until it reached minimum creep rate and after that, it decreased. The stress relaxation rate is fast and approached zero after 1.5 seconds after the beginning of the stress relaxation. And the larger the applied stress is, the larger the internal stress is. By the evaluation of mobility of dislocation, the dislocations glide viscously in STS31OJlTB but it is the dislocations glide viscously which N passes by cutting Cr atom rather than typical viscosity movement after calculating mobility of dislocation.