• The Journal of Engineering Geology
• /
• v.26 no.1
• /
• pp.33-49
• /
• 2016

The study area, located in Sinam-ri, Ulsan, in the southeastern part of the Korean Peninsula, is mainly composed of hornblende granite (ca. 65 Ma). Fracturing and reactivation of a fault striking ENE-WSW was strongly controlled by the intrusion of a mafic dyke (ca. 44 Ma), which behaves as a discontinuity in the mechanically homogeneous pluton, increasing the instability of the basement in this area. A geometric and kinematic study undertaken to interpret the faults and fractures was performed in a trench excavated almost perpendicular to the orientation of the dyke. The analysis of structural elements, such as dykes, veins, and faults, is used to infer the deformation history and to determine the paleostress orientations at the time of formation of the structures. The deformation history established based on this analysis is as follows: (1) NNE-SSW, E-W, ENE-WSW, and NE-SW trending fractures had already developed in the pluton before dyke intrusion; (2) felsic dykes intruded under conditions of σ_Hmax oriented N-S and σ_Hmin oriented E-W; (3) mafic dykes intruded under conditions of σ_Hmax oriented E-W and σ_Hmin oriented N-S; (4) dextral reactivation of the main fault associated with the development of hydrothermal quartz veins under conditions of σ_Hmax oriented E-W and σ_Hmin oriented N-S; (5) sinistral reactivation of the main fault and high-angle normal faults under conditions of σ_Hmax oriented NE-SW and σ_Hmin oriented NW-SE; and (6) dextral reactivation of the main fault and NE-SW low-angle reverse faults under conditions of σ_Hmax oriented NW-SE and σ_Hmin oriented NE-SW. These results are consistent with the tectonic history of the Pohang-Ulsan block in the southeastern part of the Korean Peninsula, and indicates the tectonic deformation of the southern area of the Ulsan fault bounded by Yangsan fault was analogous to that of the Pohang-Ulsan area from the Cenozoic. This work greatly aids the selection of sites for critical facilities to prevent potential earthquake hazards in this area.

• The Journal of Korean Society for Radiation Therapy
• /
• v.22 no.1
• /
• pp.33-39
• /
• 2010

Purpose: It is very important to confirm conformance of dose distribution that is formed with treatment planning from IMRS or IMRT. It has been a problem dropped accuracy and conformance when the field size is getting smaller because of character of the 2D ion chamber. Verification of MatriXX Phantom dose distribution with a change in the SAD. Dose distribution measurement and analysis to improve the accuracy and should be useful to evaluate the award. Materials and Methods: A use of Novalis linear accelerator 6 MV photon beams. In general, IMRS were 25 patients with small field size. The selected patients were divided into three groups on the basis of the field size. SAD was changed from 80 to 130 cm and field size to determine the dose distribution to the change, each dose was measured using MatriXX Phantom. Analysis of measured values obtained from the program for each patient through the treatment planning system comparison and analysis of the dose distribution and gamma values were expressed. Result: SAD 80, 100, and 120 cm in size in the gamma value to the investigation of patients less than $3\;cm^2$ average 0.939, 0.969, and 0.979, respectively. Patients with more than $5\;cm^2$ 0.962, 0.983, and 0.988, respectively. $5\;cm^2$ or more patients 0.982, 0.990, and 0.992, respectively. Conclusion: The error rate of less than $3\;cm^2$ field size is increased rapidly. If the field size is increased, resolution is increased by 2D ion chambers. It has been approved that it can be credible if it is around $3\;cm^2$ when measuring dose distribution using MatriXX. Adjusting geometric field size by changing SAD is likely to be very useful when you measure dose distribution using MatriXX.

• Journal of the Korean earth science society
• /
• v.43 no.5
• /
• pp.618-638
• /
• 2022

The Middle Jurassic granite dike swarm intruding into the Paleoproterozoic banded gneiss is pervasively observed in Ueumdo, Hwaseong City, mid-western Gyeonggi Massif. Based on their cross-cutting relationships in a representative outcrop, there are four dikes (UE-A, UE-C, UE-D, UE-E), and depending on the direction, there are three granite dike groups, which are NW- (UE-A dike), NW to WNW- (UE-C dike), and NE-trending (UE-D and UE-E dikes). These granite dikes are massive, medium-to coarse-grained biotite granites, and their relative ages observed in outcrops are in the order of UE-A, UE-D (=UE-E), and UE-C. The geometric analysis of the dikes indicates that the UE-A and UE-C dikes intrude under approximately NE-SW trending horizontal minimum stress fields. The UE-A dike, which showed a relatively low average SiO2 content by major element analysis, is a product of early magma differentiation compared to other dikes; therefore, it is consistent with the relative age of each dike. The ²⁰⁶Pb/²³⁸U weighted mean ages for each dike obtained from SHRIMP zircon U-Pb dating were calculated to be 167 Ma (UE-A), 164 Ma (UE-C), 167 Ma (UE-D), and 167 Ma (UE-E), respectively. The samples of the UE-A, UE-D, and UE-E dikes showed very similar ages. The UE-C dike shows the youngest age, which is consistent with the results of the relative age in the outcrops and major element analysis. Therefore, the granite dikes intruded into the Middle Jurassic (approximately 167 and 164 Ma), coinciding with those of the Gyeonggi Massif, where the Middle Jurassic plutons are geographically widely distributed. This result indicates that the wide occurrence of the Middle Jurassic plutons on the Gyeonggi Massif was formed as a result of igneous activity moving in the northwest direction with the shallower subduction angle of the subducting oceanic plate during the Jurassic.

• The Journal of Korean Society for Radiation Therapy
• /
• v.32
• /
• pp.93-109
• /
• 2020

Purpose: The radiochromic film (Gafchromic EBT3, Ashland Advanced Materials, USA) and 3-dimensional analysis system dosimetry checkTM (DC, MathResolutions, USA) were evaluated for patient-specific quality assurance (QA) of helical tomotherapy. Materials and Methods: Depending on the tumors' positions, three types of targets, which are the abdominal tumor (130.6㎤), retroperitoneal tumor (849.0㎤), and the whole abdominal metastasis tumor (3131.0㎤) applied to the humanoid phantom (Anderson Rando Phantom, USA). We established a total of 12 comparative treatment plans by the four geometric conditions of the beam irradiation, which are the different field widths (FW) of 2.5-cm, 5.0-cm, and pitches of 0.287, 0.43. Ionization measurements (1D) with EBT3 by inserting the cheese phantom (2D) were compared to DC measurements of the 3D dose reconstruction on CT images from beam fluence log information. For the clinical feasibility evaluation of the DC, dose reconstruction has been performed using the same cheese phantom with the EBT3 method. Recalculated dose distributions revealed the dose error information during the actual irradiation on the same CT images quantitatively compared to the treatment plan. The Thread effect, which might appear in the Helical Tomotherapy, was analyzed by ripple amplitude (%). We also performed gamma index analysis (DD: 3mm/ DTA: 3%, pass threshold limit: 95%) for pattern check of the dose distribution. Results: Ripple amplitude measurement resulted in the highest average of 23.1% in the peritoneum tumor. In the radiochromic film analysis, the absolute dose was on average 0.9±0.4%, and gamma index analysis was on average 96.4±2.2% (Passing rate: >95%), which could be limited to the large target sizes such as the whole abdominal metastasis tumor. In the DC analysis with the humanoid phantom for FW of 5.0-cm, the three regions' average was 91.8±6.4% in the 2D and 3D plan. The three planes (axial, coronal, and sagittal) and dose profile could be analyzed with the entire peritoneum tumor and the whole abdominal metastasis target, with planned dose distributions. The dose errors based on the dose-volume histogram in the DC evaluations increased depending on FW and pitch. Conclusion: The DC method could implement a dose error analysis on the 3D patient image data by the measured beam fluence log information only without any dosimetry tools for patient-specific quality assurance. Also, there may be no limit to apply for the tumor location and size; therefore, the DC could be useful in patient-specific QAl during the treatment of Helical Tomotherapy of large and irregular tumors.

• Journal of the Korean earth science society
• /
• v.21 no.5
• /
• pp.583-594
• /
• 2000

The Middle Carboniferous Yobong Formation with North-South trending is distributed in the Yeongheungri and Samokri of Yeongwoleup, Kangwon Province, Korea. A light gray thick and massive pure limestone is developed in the middle part of the Yobong Formation and it has been exploited for a long time. This study was carried out to investigate the lithological characteristics and geochemical compositions of the limestones and to figure out how geologic structures control the disribution of the limestones of the formation. The limestones of the Yobong formation are characterized by the fine and dense textures and the light gray to light brown in color. The limestones are composed of crinoid fragments, small foraminifers, fusulinids, gastropods, ostracods, etc. Based on the amount of grains and matrix, the Yobong Limestone can be classified as fine packstones and wackestones. The chemical analysis of limestones of the Yobong Formation was carried out to measure the contents of CaO, MgO, Al$_2$O$_3$, Fe$_2$O$_3$ and SiO$_2$. The content of CaO ranges from 48.12 to 59.31% and its average is about 54.52%. The average content of MgO is about 0.32% and the coutents of Al$_2$O$_3$, Fe$_2$O$_3$ and SiO$_2$ are relatively low. The amounts of Al$_2$O$_3$, Fe$_2$O$_3$ and SiO$_2$ of the limestones vary according to the kinds of limestone and their stratigraphical horizons in the formation. Generally, the CaO content of the limestones of the Yobong Formation decreases towards the top of the formation. Using geometric and structural analysis, we determined five progressively overprinted phases of deformation recorded in the study area. The anticline and syncline formed during the first and fourth deformation had controlled the distribution pattern of the Yobong Limestone of the Yobong Formation. The structures of deformation D$_1$ consist of F$_1$ isoclinal folds and foliations. The D$_2$ deformation had formed the isoclinal interstratal F$_2$ folds and axial plane cleavages which are locally developed within mudstones. The structural elements of deformation D$_3$ are axial plane cleavages associated with recumbent F$_3$ folds. These structures are overprinted by meso-scale and regional F$_4$ folds which are regionally dominant. Finally, the structures of D$_5$ consist of the thrust faults and folds associated with the thrust faults.

• Proceedings of the KOR-KST Conference
• /
• 1995.02a
• /
• pp.3-32
• /
• 1995

The Highway Capacity Manual specifies procedures for evaluating intersection performance in terms of delay per vehicle. What is lacking in the current methodology is a comparable quantitative procedure for ass~ssing the safety-based level of service provided to motorists. The objective of the research described herein was to develop a computational procedure for evaluating the safety-based level of service of signalized intersections based on the relative hazard of alternative intersection designs and signal timing plans. Conflict opportunity models were developed for those crossing, diverging, and stopping maneuvers which are associated with left-turn and rear-end accidents. Safety¬based level-of-service criteria were then developed based on the distribution of conflict opportunities computed from the developed models. A case study evaluation of the level of service analysis methodology revealed that the developed safety-based criteria were not as sensitive to changes in prevailing traffic, roadway, and signal timing conditions as the traditional delay-based measure. However, the methodology did permit a quantitative assessment of the trade-off between delay reduction and safety improvement. The Highway Capacity Manual (HCM) specifies procedures for evaluating intersection performance in terms of a wide variety of prevailing conditions such as traffic composition, intersection geometry, traffic volumes, and signal timing (1). At the present time, however, performance is only measured in terms of delay per vehicle. This is a parameter which is widely accepted as a meaningful and useful indicator of the efficiency with which an intersection is serving traffic needs. What is lacking in the current methodology is a comparable quantitative procedure for assessing the safety-based level of service provided to motorists. For example, it is well¬known that the change from permissive to protected left-turn phasing can reduce left-turn accident frequency. However, the HCM only permits a quantitative assessment of the impact of this alternative phasing arrangement on vehicle delay. It is left to the engineer or planner to subjectively judge the level of safety benefits, and to evaluate the trade-off between the efficiency and safety consequences of the alternative phasing plans. Numerous examples of other geometric design and signal timing improvements could also be given. At present, the principal methods available to the practitioner for evaluating the relative safety at signalized intersections are: a) the application of engineering judgement, b) accident analyses, and c) traffic conflicts analysis. Reliance on engineering judgement has obvious limitations, especially when placed in the context of the elaborate HCM procedures for calculating delay. Accident analyses generally require some type of before-after comparison, either for the case study intersection or for a large set of similar intersections. In e.ither situation, there are problems associated with compensating for regression-to-the-mean phenomena (2), as well as obtaining an adequate sample size. Research has also pointed to potential bias caused by the way in which exposure to accidents is measured (3, 4). Because of the problems associated with traditional accident analyses, some have promoted the use of tqe traffic conflicts technique (5). However, this procedure also has shortcomings in that it.requires extensive field data collection and trained observers to identify the different types of conflicts occurring in the field. The objective of the research described herein was to develop a computational procedure for evaluating the safety-based level of service of signalized intersections that would be compatible and consistent with that presently found in the HCM for evaluating efficiency-based level of service as measured by delay per vehicle (6). The intent was not to develop a new set of accident prediction models, but to design a methodology to quantitatively predict the relative hazard of alternative intersection designs and signal timing plans.

• Progress in Medical Physics
• /
• v.24 no.4
• /
• pp.253-258
• /
• 2013

The purpose of this study is to evaluate and analyze the relationship between the external radiation dose reconstruction which is transmitted from the patient who receives radiation treatment through electronic portal imaging device (EPID) and the internal dose derived from the Monte Carlo simulation. As a comparative analysis of the two cases, it is performed to provide a basic indicator for similar studies. The geometric information of the experiment and that of the radiation source were entered into Monte Carlo n-particle (MCNPX) which is the computer simulation tool and to derive the EPID images, a tally card in MCNPX was used for visualizing and the imaging of the dose information. We set to source to surface distance (SSD) 100 cm for internal measurement and EPID. And the water phantom was set to be 100 cm of the source to surface distance (SSD) for the internal measurement and EPID was set to 90 cm of SSD which is 10 cm below. The internal dose was collected from the water phantom by using mesh tally function in MCNPX, accumulated dose data was acquired by four-portal beam exposures. At the same time, after getting the dose which had been passed through water phantom, dose reconstruction was performed using back-projection method. In order to analyze about two cases, we compared the penetrated dose by calibration of itself with the absorbed one. We also evaluated the reconstructed dose using EPID and partially accumulated (overlapped) dose in water phantom by four-portal beam exposures. The sum dose data of two cases were calculated as each 3.4580 MeV/g (absorbed dose in water) and 3.4354 MeV/g (EPID reconstruction). The result of sum dose match from two cases shows good agreement with 0.6536% dose error.

• Journal of the Korean Society of Radiology
• /
• v.15 no.5
• /
• pp.741-748
• /
• 2021

In this study, we evaluated image quality by changing collimator length and detector thickness using the Geant4 Application for Tomographic Emission (GATE) simulation tool. The gamma camera based on the Cadimium Zinc Telluride (CZT) and NaI detectors is modeled. In addition the images were acquired by setting 1, 2, 3, 4, 5, and 6 cm collimator length and 1, 3, 5, and 7 mm detector thickness using point source and phantom, which is designed by each diameter (4.45, 3.80, 3.15, 2.55 mm) with 447, 382, 317, and 256 Bq. The sensitivity (cps/MBq) for point source, and signal to noise ratio (SNR) and profile for phantom at the 4.45 mm by drwan the region of interests were used for quantitative analysis. Based on the results, the sensitivity according to collimator length is 2.3 ~ 48.6 cps/MBq for CZT detector, and 1.8 ~ 43.9 cps/MBq for NaI detector. The SNR using phantom is 3.6~9.8 for CZT detector, and 2.9~9.5 for NaI detector. As the collimator length is increased, the image resolution is also improved according to profile results based on the CZT and NaI detector. In addition, the senistivity for detector thickness is 0.04 ~ 0.12 cps/MBq for CZT detector, and 0.03 ~ 0.11 cps/MBq. The SNR using phnatom is 7.3~9.8 count for CZT detector, and 5.9~9.5 for NaI detector. As the detector thickness is increased, the image resolution is decreased according to profile results based on the CZT and NaI detector due to scatter ray. In conclusion, we need to set the geometric material such as detector and collimator to acuquire suitable image quality in nuclear medicine.

• Clinical and Experimental Pediatrics
• /
• v.48 no.9
• /
• pp.960-968
• /
• 2005

Purpose : This multi-center, open-label, clinical study was designed to evaluate the safety and immunogenicity of a trivalent, live, attenuated measles-mumps-rubella(MMR) vaccine, $Priorix^{TM}$ in Korean children. Methods : From July 2002 to February 2003, a total of 252 children, aged 12-15 months or 4-6 years, received $Priorix^{TM}$ at four centers : Han-il General Hospital, Kyunghee University Hospital, St. Paul's Hospital at the Catholic Medical College in Seoul, and Korea University Hospital in Ansan, Korea. Only subjects who fully met protocol requirements were included in the final analysis. The occurrence of local and systemic adverse events after vaccination was evaluated from diary cards and physical examination for 42 days after vaccination. Serum antibody levels were measured prior to and 42 days post-vaccination using IgG ELISA assays at GlaxoSmithKline Biologicals (GSK) in Belgium. Results : Of the 252 enrolled subjects, a total of 199 were included in the safety analysis, including 103 from the 12-15 month age group and 96 from the 4-6 year age group. The occurrence of local reactions related to the study drug was 10.1 percent, and the occurrence of systemic reactions was 6.5 percent. There were no episodes of aseptic meningitis or febrile convulsions, nor any other serious adverse reaction. In immunogenicity analysis, the seroconversion rate of previously seronegative subjects was 99 percent for measles, 93 percent for mumps and 100 percent for rubella. Both age groups showed similar seroconversion rates. The geometric mean titers achieved, 42 days pos-tvaccination, were : For measles, in the age group 12-15 months, 3,838.6 mIU/mL [3,304.47, 4,458.91]; in the age group 4-6 years, 1,886.2 mIU/mL [825.83, 4,308.26]. For mumps, in the age group 12-15 months, 956.3 U/mL [821.81, 1,112.71]; in the age group 4-6 years, 2,473.8 U/mL [1,518.94, 4,028.92]. For rubella, in the age group 12-15 months, 94.5 IU/mL [79.56, 112.28]; in the age group 4-6 years, 168.9 IU/mL [108.96, 261.90]. Conclusion : When Korean children in the age groups of 12-15 months or 4-6 years were vaccinated with GlaxoSmithKline Biologicals' live attenuated MMR vaccine ($Priorix^{TM}$), adverse events were limited to those generally expected with any live vaccine. $Priorix^{TM}$ demonstrated excellent immunogenicity in this population.

• Clinical and Experimental Pediatrics
• /
• v.50 no.6
• /
• pp.556-564
• /
• 2007

Purpose : We hypothesized that the persisting bronchial hyperresponsiveness (BHR) of adolescents with asthma remission may be controlled mainly by genetic factors, and the BHR of symptomatic asthma by airway inflammation. ${\beta}_2$-adrenoceptor gene is considered to be a candidate gene in the development of BHR. Thus, ${\beta}_2$-adrenoceptor gene polymorphism may be associated with the BHR of adolescents with asthma remission, but not with the BHR of symptomatic asthma. To evaluate this hypothesis, ${\beta}_2$-adrenoceptor gene polymorphism at 2 sites (Arg16-Gly, Gln27-Glu) were examined. Methods : Two hundred two adolescents with BHR ($PC_{20}<18\;mg/mL$) and long term remission (neither asthma-related symptoms nor medication during the previous 2 years) of their asthma (remission group), 182 adolescents with symptomatic asthma (symptomatic group), and 200 healthy adolescents (control group) were studied. Asthma phenotypes were determined using methacholine bronchial provocation test and skin prick test. Genotypes of ${\beta}_2$-adrenoceptor polymorphism were evaluated by PCR-based methods. Results : Gly/Gly allele and Gly16-Gln27 haplotype were more prevalent in the remission group than in the control group (P=0.01, P=0.02), although there was no difference between the symptomatic group and the control group. In the remission group, there was significant difference in geometric mean of $PC_{20}$ among the 3 groups subdivided by the number of Gly16-Gln27 haplotype, showing that the Gly16-Gln27 haplotype was positively associated with BHR. However, no association was found between Gly16-Gln27 haplotype and BHR in the symptomatic group. Conclusion : This study demonstrates that ${\beta}_2$-adrenoceptor polymorphism at amino acid 16 and 27 was associated with BHR persisting in adolescents with asthma remission.