• Economic and Environmental Geology
• /
• v.23 no.4
• /
• pp.411-424
• /
• 1990

Mechanical, physical and petrographic properties of seventeen marble specimens collected from ten marble mines in Korea were investigated. Studied marbles were mainly composed of calcite, dolomite, and various amounts of serpentine, tremolite, olivine, quartz and opaque minerals. Complete and sutured textures were dominant. Compressive strength measured normal to the bedding plane is larger almost two times than that measured parallel to the bedding plane. From the results of Shore hardness test on marbles, water content was an important factor to decrease Shore hardness values. Engineering geological properties, especially, compressive strength, Young's modulus, wear resistance and water absorption could be controlled by the presence of quartz, and the type of marble texture. Water absorption-porosity, compressive strength-Young's modulus, and impact strength index-Los Angeles abrasion couples show good correlation. According to the comparative utility as commercial stone, it could be concluded that marbles from the Banglim mine, Songbo mine, Kwangdeok mine and Bongjeong mine were superior to that of other studied marbles.

• Wind and Structures
• /
• v.1 no.1
• /
• pp.77-109
• /
• 1998

An evaluation and comparison of seven of the world's major building codes and standards is conducted in this study, with specific discussion of their estimations of the alongwind, acrosswind, and torsional response, where applicable, for a given building. The codes and standards highlighted by this study are those of the United States, Japan, Australia, the United Kingdom, Canada, China and Europe. In addition, the responses predicted by using the measured power spectra of the alongwind, acrosswind and torsional responses for several building shapes tested in a wind tunnel are presented and a comparison between the response predicted by wind tunnel data and that estimated by some of the standards is conducted. This study serves not only as a comparison of the response estimates by international codes and standards, but also introduces a new set of wind tunnel data for validation of wind tunnel-based empirical expressions.

• Tunnel and Underground Space
• /
• v.18 no.2
• /
• pp.134-148
• /
• 2008

The state of in situ stress is an important factor in considering the suitability of a site as a geological repository for nuclear waste. In this study, three-dimensional distinct numerical analysis was conducted to investigate the effect of deformation zones on the state of stress in the Oskarshamn area, which is one of two candidate sites in Sweden. A discontinuum numerical model was constructed by explicitly representing the numerous deformation zones identified from site investigation and far-field tectonic stress was applied in the constructed model. The numerical model successfully captured the variation of measured stress often observed in the rock mass containing large-scale fractures, which shows that numerical analysis can be an effective tool in improving the understanding of the state of stresses. Discrepancies between measured and modelled stress are attributed to the inconsistent quality of measured stress, uncertainty in geological geometry. and input data for fractures.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2004.04a
• /
• pp.293-296
• /
• 2004

The objective of this study was to decide the designing factor for remediaton of the contaminated site. The soil and ground-water samples were analyzed and hydro- geological characteristics was assayed for the survey of pollution level. Also air-permeability test and MPN(most probable number) test were conducted for selecting the designing factor. The contaminants were mainly found in north-west part of the site and were expected to move toward the south. Ex-situ technology was expected more useful than in-situ one with the results of air-permeability test saying that air permeability was relatively low. Additional microbes were expected for remediation efficiency because residual microbes were loosely populated. The choosing of the designing factor was requisite for remediation of contaminated site.

• The Korean Journal of Quaternary Research
• /
• v.17 no.2
• /
• pp.167-168
• /
• 2003

The Upo wetland, the largest natural wetland in Korea, is located in Changnyeong-gun, Gyeongsannam Province ($35^{\circ}33'$ N, $128^{\circ}25'$ E), and 70 km upstream from the Nakdong River estuary. Unlike most other Korean wetlands that have been destroyed under the name of economic development, the Upo wetland has been able to preserve its precious ecosystem throughout the years. Thanks to increased public awareness about natural wetlands and environmental conservation, the Korean Ministry of Environment designated the Upo wetland an 'Ecological Conservation Area' on July 26th, 1997. On March 2nd of the following year, the Upo wetland (8.54 $\textrm{km}^2$) was designated a 'Protected Wetland' in accordance with the international Ramsar Treaty. A 4.49m long (from 9.73 to 5.24 m in altitude) UP-1 core ($35^{\circ}33'05"N$, $128^{\circ}25'17"E$), recovered in the marginal part of the Upo wetland, is divided into eight buried paleosol units of different ages on the basis of the abundance of color mottles and vertical color variations (Aslan et al., 1998). Radiocarbon datings suggested that the paleosol profile represent the last 5700 years. The entire section of the core was more or less subjected to pedogenetic processes, and shows very weak to moderate soil profile development. These Holocene paleosols are therefore regarded as synsedimentary soils of deluvium (deposits formed by floods) origin (Sycheva et al., 2003). Unit 1 to 5 paleosols are generally silt-rich and exhibit moderate profile development. The boundaries between the units are somewhat distinguishable, but not so clear cut. This is due to variable repeated combination of accumulation, denudation and soil forming processes within various periods. Mottle textures gradually decrease in abundance with increasing clay content in Unit 6, which results in weak profile development. The lower boundary of Unit 6 lies around about 2000 yrBP, the beginning of Subatlantic in Korea (Kim et al., 2001). Abrupt sediment textural change is detected in Unit 7, which is interpreted to indicate the human activities on the Upo wetland. Unit 8 represents the recent soil forming processes. The preliminary results of this ongoing study imply the primary factor for pedogenetic processes is the water table fluctuations related to the sedimentary textures like grain size distributions, and the geomorphological stability of the Upo wetland.o wetland.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.11 no.3
• /
• pp.253-257
• /
• 2013

Geology, hydrogeology, and geochemistry are the main technical siting factors of a geological repository for spent nuclear fuels. This paper evaluated the siting criteria of overseas geological repository with related to hydrogeologic properties, such as hydraulic conductivity, partitioning coefficient, dispersion coefficient, boundary condition, and water age. Each country establishes the siting criteria based on its important geological backgrounds and information, and social environment. For example, Sweden and Finland that have decided a crystalline rock as a host rock of a geological repository show different siting criteria for hydraulic conductivity. In Sweden, it is preferable to avoid area where the hydraulic conductivity on a deposition hole scale (~30m) exceeds $10^{-8}m/s$, whereas Finland does not decide any criterion for the hydraulic conductivity because of limited data for it. In addition, partitioning coefficients should be less than 10-1 of average value in Swedish crystalline bedrock. However, the area where shows 100 times less than average partitioning coefficients of radionuclides in crystalline rock should be avoided in Sweden. In German, the partitioning coefficients for the majority of the long-term-relevant radionuclides should be greater than or equal to $0.001m^3/kg$. Therefore, it is strongly required to collect much and exact information for the hydrogeologic properties in order to set up the siting criteria.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.8 no.4
• /
• pp.165-175
• /
• 2005

Geographic Information System(GIS) is useful to preserve cultural heritage and land use management using both spatial information management technique and spatial analysis function in cultural heritage management. The purpose of this study is to build a database of pottery and kiln sites in South Korea, to analyze site locations and finally to make prediction model. The locations of 1,200 sites are put into GIS database. Such factor elevation, slope angle, aspect, horizontal/vertical distance from the nearest water are analyzed. Each factor was statistically analyzed on GIS and represented to rank 1-5. Pottery/kiln can be predicted by the spatial analysis function in overlay methods. As a result of this study, preliminary application of prediction model shows that the high potential area is between the slope and alluvial plain. Field survey in the Sungbuk-dong in Daejeon city supports the preliminary result. More data can make improve efficient prediction model in unknown areas.

• Tunnel and Underground Space
• /
• v.20 no.6
• /
• pp.446-454
• /
• 2010

CAES-G/T (Compressed Air Energy Storage - Gas Turbine) power generation is a likely option for the buffer facility stabilizing the fluctuation of the renewable powers, such as wind and solar powers. Considering the geological conditions, the underground CAES facility is most probable if the CAES-G/T generation is planed in Korea. In this kind of facility, a concrete plug is installed to seal the compressed air in the container, so that the selection of the shape and dimension of concrete plug could be a critical design factor. The stability evaluation of two types of plug was carried out by investigating the distribution of the factor of safety in the plugs and the distribution of contact pressure over the contact surface. The analysis result shows that the taper-shaped plug is more structurally stable than the wedge-shaped plug for the given geological condition. Possible separation of the rock-concrete interface around the spring line of the wedge-shaped plug is anticipated, which means the possible leakage of compressed air through the side wall and also means the poor mobilization of frictional resistance on that area.

• The Journal of the Petrological Society of Korea
• /
• v.24 no.3
• /
• pp.209-231
• /
• 2015

In granite quarry, stones are generally quarried along easily separating planes called as 'rock cleavage'. Because orientation and characteristics of the rock cleavage are directly involved with easy quarrying, it is the most important factor on selecting a direction of digging. Using AMS (anisotropy of magnetic susceptibility), we attempt to interpret rock fabrics in Geochang Granite Stone (JS, SD, AR, GD, BW, MD quarry) and discuss about determination of rock cleavages and correlation between the rock fabrics and cleavages. Based on mean susceptibility, thermo-susceptibility curves, and hysteresis parameters, Ti-poor MD and/or PSD magnetites are the main contributor to AMS of the granite stones. The systematic magnetic foliations with sub-vertical dip angle are developed in the whole granite quarries. In most of the granite quarries, the magnetic foliations are significantly consistent with grain plane. In the BW quarry, which has higher $P_J$ values than the others, the magnetic foliations coincide exceptionally with rift plane. These results suggest that rock cleavages in granite stone are related to rock fabrics meaning shape and spatial arrangement of crystals. Magnetic fabrics analysis using AMS method, therefore, can be a quantitative and effective tool for determination of rock cleavages in granite quarry.

• Korean Journal of Soil Science and Fertilizer
• /
• v.50 no.5
• /
• pp.357-368
• /
• 2017

To establish new metal groundwater standard, 5 metals such as aluminum, chromium, iron, manganese, and selenium were evaluated by Chemical Ranking Of groundWater pollutaNts (CROWN) including possibility of exposure, toxicity, interest factor, connection standard for other media, and data reliability. 430 groundwater samples in 2013 and 2014 were collected semiannually from 110 groundwater wells and they were analyzed for selenium, manganese, iron, chromium, and aluminum. For this study, 430 groundwater samples were categorized into 3 geological distribution features, such as igneous, metamorphic, and sedimentary rock region and geological background levels were divided by pre-selection methods. For the results, the average concentrations of aluminum, chromium, iron, manganese, and selenium in 430 groundwater samples were $0.0008mg\;L^{-1}$, $0.0001mg\;L^{-1}$, $0.174mg\;L^{-1}$, $0.083mg\;L^{-1}$, and $0.0004mg\;L^{-1}$, respectively. In addition, among various geologies, average concentration of selenium was the highest in igneous rock region, average concentrations of chromium, manganese and aluminum were the greatest in sedimentary rock region, and average concentration of iron was the most high in metamorphic rock region. As a result of the geological background concentration with pre-selection method, background concentrations of selenium and aluminum in groundwater samples were the highest from sedimentary rock as $0.0010mg\;L^{-1}$ and $0.0029mg\;L^{-1}$ and background concentrations of manganese and iron in groundwater samples were the greatest from metamorphic rock as $0.460mg\;L^{-1}$ and $1.574mg\;L^{-1}$, and no chromium background concentration in groundwater samples was found from all geology.