• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.195-200
• /
• 2012

In this study, parameters and requirements of an 120kW class monorail planetary gearbox was analysed and the adaptive planetary gearbox design was selected. The specification of the sun gear, planetary gear and carrier was set and the profile & lead was optimized. The mechanical efficiency of the optimized one and the original one was observed. Dynamo-tester system was used to observe the mechanical efficiency of the planetary gearbox. A dynamo unit was connected with the planetary gearbox which straightened through the motor by a coupling. The standard tooth shape planetary gearbox and modified tooth shape planetary gearbox were used as test pieces and the rotation speed was set from 600 to 6000rpm with 600rpm, 2.5min one step. In order to check the mechanical efficiency of the planetary gearbox, the tests were done as follows. 1) The power loss between driving motor and dynamo tester. 2) Temperature variation by different rotation speeds. 3) Noise variation by different rotation speeds.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.25-34
• /
• 1999

In this study, the sliding wear in spur gears, using Archard's wear model, is analyzed. Formulas of tooth sliding wear depth along the line of action are derived. The tooth profile is modified Id make a smooth transmission of the normal loads and the cylinder profile for reducing the pressure spike is suggested. The sliding wear rate is calculated with these profiling results. We expect these modification methods to contribute to the reduction of sliding wear in the root and the tip of tooth and tooth edge.

• 한국정밀공학회지
• /
• 제13권4호
• /
• pp.129-135
• /
• 1996

The area of gear vibration and noise, has recently been the focus of many studies. The proper kinematic and geometric design of gears, the mathematical modeling of gear system are essential for a good design. This work present a gear disign for reducing noise, and practical approaches used for machinery noise reduction slong with the summary of methods available for predicting gear noise in terms of the transmis- sion error, and show a comparative study with other methods. A new tooth profile modification is proposed for reducing vibration and noise of involute gears. The method is based on the use of cubic spline curves. The tooth profile is constrained to assume an involute shape during the loaded operation. Thus the new gear profile assures conjugate motion at all points along the line of action. The new profile is found to result in a more uniform static transmission error compared to not only standard involute profile but also modificated profile therby contributing to the improvement of vibration and noise characteristics of the gear.

• Tribology and Lubricants
• /
• 제4권2호
• /
• pp.60-67
• /
• 1988

Conventional theory of gear mechanism can't be applied to analyze the harmonic drive due to specific movement of the teeth. This paper deals with an analysis of kinematics and geometry of the tooth engagement of a harmonic drive comprising circular spline, flexspline and wave generator. A theoretical new tooth profile of the flexspline in meshing internal rigid gear with involute profile is obtained. Characteristics of harmonic drive reducer are shown according to parameters such as deviation coefficient, deviation distance, addendum modification coefficient. As an example, the design of harmonic drive with 1:80 reduction ratio is presented.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.66-71
• /
• 2016

For the manual transmission gearbox used in the automotive industry, gear meshing transmission error is the main source of noise known as gear whine, and radiated gear whine noise plays an important role in the whole gearbox. Therefore, in order to keep competitive in the automotive market, the NVH performance of transmission gearboxes is increasingly important for automotive manufacturers when a new product is developed. In this paper, in order to achieve an optimized tooth contact pattern, gear tooth modification is applied to make up for the deformation of the teeth owing to load. A five-speed MT gearbox is firstly modeled in RomaxDesign software and the prediction of transmission error under the loaded torques is studied and compared. From the simulation, the transmission error and maximum contact stress are also simulated and compared after tooth modification of the loaded torques. Finally, the simulation results are used to optimize the whole gearbox design and the final gearbox prototype is testified to obtain NVH performance in a semi-anechoic room.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.338-343
• /
• 2009

In this paper, Verification of the qualitatively identical relationships existing between simulation data and experimental results allowed for a new analysis procedure of a planetary gear set -- in an automatic transmission -- to be conducted. Tooth profiles were found to be crucial to the gear mesh forces of the planetary gear set. Based on Kahraman's Model[8], dynamic resonances of the planetary gear set were found to be out of operating range. Most importantly, a 2DPLANETARY FEM program, an innovative design tool for planetary gear sets, was utilized.

• 한국소음진동공학회논문집
• /
• 제20권3호
• /
• pp.242-248
• /
• 2010

In this paper, Verification of the qualitatively identical relationships existing between simulation data and experimental results allowed for a new analysis procedure of a planetary gear set -- in an automatic transmission -- to be conducted. Tooth profiles were found to be crucial to the gear mesh forces of the planetary gear set. Based on Kahraman's Model, dynamic resonances of the planetary gear set were found to be out of operating range. Most importantly, a 2DPLANETARY FEM program, an innovative design tool for planetary gear sets, was utilized.

• 한국정밀공학회지
• /
• 제16권12호
• /
• pp.99-108
• /
• 1999

A four-degree-of-freedom non-linear model with time varying mesh stiffness has been developed for the dynamic analysis of spur gear trains. The model includes a spur gear pair, two shafts, two inertias representing load and prime mover. In the model, developed several factors such as time varying mesh stiffness and damping, separation of teeth, teeth collision, various gear errors and profile modifications have been considered. Two computer programs are developed to calculate stiffness of a gear pair and transmission error and the dynamic analysis of modeled system using time integration method. Dynamic tooth and mesh forces, dynamic factors are calculated. Numerical examples have been given, which shows the time varying mesh stiffness ha a significant effect upon the dynamic tooth force and torsional vibrations.

• 한국정밀공학회지
• /
• 제22권4호
• /
• pp.159-166
• /
• 2005

This study deals with the correction of gear tooth profile error by finish roll forming. First, we experimentally confirmed that the tooth profile error is a synthesis of the concave error and the pressure angle error. Since various types of tooth profile errors appear in the experiments, we introduced evaluation parameters for rolling gears to objectively evaluate profile quality. Using these evaluation parameters, we clarified the relationship among the tooth profile error, the addendum modification factor (A. M. factor), and the tool loading force. We verified the character of concave error, pressure angle error, tool loading force and number of cycles of finish roll forming by using a forced displacement method. This study makes clear that tool loading force and number of cycles of finish roll forming are very important factors that affect involute tooth profile error. The results of the experiment and analysis show that the proposed method reduces concave and pressure angle errors.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.190-196
• /
• 2003

The load sharing and teeth deflection of helical gear system are analyzed to investigate the deformation overlap. The deformation overlap, which is calculated by the results of displacement analysis, is suggested as the basis for the tooth profile modification. Helical gear systems are formulated as contact problems, and solved by elastic contact theory and FEM. The developed computer program, which offers gear teeth deflection and deformation overlap, will be of much help to the improved design of manual transmissions for automobiles.