• Journal of the Optical Society of Korea
• /
• 제13권1호
• /
• pp.146-151
• /
• 2009

A Gaussian beam of single mode fiber laser was changed into a ring-shaped pattern after it was transmitted through the hollow optical fiber. The ring-shaped beam was focused on a plane by an f-. lens and it was scanned by a Galvano-mirror. The spatial profile of laser energy incident on a plane had two peaks at both sides of the scanned linear track. The profile was compared with the result obtained when the Gaussian beam was dithered transversely by an acousto-optic modulator. It is found that hollow optical fiber beam shaper can replace acousto-optic beam dithering device which is employed in a laser induced thermal printing system.

• 한국정밀공학회지
• /
• 제11권1호
• /
• pp.201-210
• /
• 1994

A theoretical heat-flow model incorporating with a constant moving CO$_{2}$ laser beam has been analyzed to predict depth and the shape of bead section during last beam welding. The laser beam is exponentially attenuated with an abosrption coefficient in the material. The solution can be expressed in terms of normalized variables. The experimental data were generated by usint CW 2 CO$_{2}$ laser with multi beam mode and CW 3 kW CO$_{2}$laser with Gaussian mode. The specimens were made as bead-on-plate welds for SM 10C, STS 304, STS 316, STS 420 and pure Nickel. The maximum possible penetration depth and the shape of beas section for given sources of laser power, travel speed and beam spot size can be prdicted with this model in a given material.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2006년 추계학술발표대회 개요집
• /
• pp.207-209
• /
• 2006

This study is about an effect on a characteristics of the laser heat treatment as a optic systems which have a transverse beam mode each other. An experiment are carried out using a circular gaussian beam optics and rectangular beam optics. Generally, the optic system which has a uniform power intensity is mainly used in the laser heat treatment process. In this study, we would like to carried out experiments simultaneously using two optic systems and research the differences from a characteristics of the laser heat treatment.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1759-1761
• /
• 1996

Md:YAG laser has been used in many applications such as micromachining, nonlinear optical experiments, holography, and rangefinding. These applications quite often require operation of the laser at the $TEM_{00}$ mode since this mode produces the smallest beam divergence, the highest power density, and, hence, the highest brightness. In this study, a pinhole is put between a rod and a half mirror to make the $TEM_{00}$ mode, and then we measured the intensity distribution of the output beam as reducing the diameter of the pinhole from 6mm to 1.5mm. As a result, the optimum size of the pinhole fixed in a resonator to make the $TEM_{00}$ mode was obtained, and we found out that the output beam of the pulsed Nd:YAG laser with a single elliptical cavity has a Gaussian distribution.

• 한국광학회지
• /
• 제18권4호
• /
• pp.280-285
• /
• 2007

다중모드 광섬유 테이퍼(taper)를 이용하여 레이저와 광섬유 혹은 두 개의 서로 다른 광섬유 사이의 효과적인 광결합을 위한 모드 크기 변환기를 제안하고 구현하였다. 이 소자의 입력 단은 다중 모드 구조이고 출력단은 단일 모드 구조이다. 소자의 구조 및 광원과 소자사이의 결합 조건이 결합 효율에 미치는 영향을 이론적으로 분석하였다. 이론적 결과는 제안된 소자가 가우시안 빔을 단일모드 광섬유로 거의 손실 없이 결합할 수 있는 것을 보였다. 제안된 소자를 두 개의 마이크로 토치가 부착된 장비를 이용해 제작하였다. 실험 결과 제작된 다중모드광섬유 테이퍼를 통해 $50\;{\mu}m$ 빔 크기를 가지는 가우시안 빔을 단일모드 광섬유로 효과적으로 결합할 수 있는 것을 보였다. 소자의 삽입 손실은 1.3 dB였다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2007년도 하계학술발표회 논문집
• /
• pp.141-142
• /
• 2007

• 한국광학회:학술대회논문집
• /
• 한국광학회 1989년도 제4회 파동 및 레이저 학술발표회 4th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.43-45
• /
• 1989

Single mode pulsed incidence dye laser which has TEMoo spatial beam pattern, near gaussian temporal shape and narrow band width(less than 500MHz) has been constructed The improved performance comes as a results of cavity length(~5cm) and definition of optical path by means of longitudinal pumping. Using 1.0X10-4M RH-6G dye, conversion efficiency was approximately 2.2% and tuning range was 548-564nm.

• 한국공작기계학회논문집
• /
• 제16권2호
• /
• pp.70-77
• /
• 2007

The application of focused ion beam(FIB) technology has been broadened in the fabrication of nanoscale regime. The extended application of FIB is dependent on complicated reciprocal relation of operating parameters. It is necessary for successful and efficient modifications on the surface of silicon substrate. The primary effect by Gaussian beam intensity is significantly shown from various aperture size, accelerating voltage, and beam current. Also, the secondary effect of other process factors - dwell time, pixel interval, scan mode, and pattern size has affected to etching results. For the process analysis, influence of the secondary factors on FIB micromilling process is examined with respect to sputtering depth during the milling process in silicon material. The results are analyzed by the ratio of signal to noise obtained using design of experiment in each parameter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 추계학술대회 논문집 학회본부 C
• /
• pp.594-596
• /
• 2000

The best simulation condition for the fiber collimator that uses ball lenses was investigated. This kind of fiber collimator can be used in a Micro-Optical-Cross-Connects(MOXC). MOXC is composed of collimating ball lenses, micro mirrors and single-mode fibers. In order to design a MOXC, it is very important to calculate beam path, beam radius, divergence angle that determines the insertion loss of the MOXC. Since the beam profile from the fiber facet is not exact Gaussian profile, it was found that the simulation condition in which beam waist exists on the fiber facet, ignoring Numerical Aperture(NA), gives best agreement with the experimental results. Beam radii were measured with conventional knife edge method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.552-556
• /
• 1997

The Direct Metal Prototyping(DMP), one of the rapid prototyping technologies, allows the manufacturing of three-dimensional metallic parts using metal powders directly from the CAD data. Laser power and scanning speed are the most important variables of the process. The objective of this study is to obtain the design data for laser power and scanning speed to bond metal powders effectively using the finite element method. To obtain the design values, a numerical analysis considering two-dimensional heat transfer during the sintering of metal powder layers of the process was performed. The laser beam has been modeled to have directionality in its heat flux distribution, i. e., in the scanning direction a Gaussian beam mode distribution has been assumed and in the thickness direction a square beam mode distribution. The three-dimensional irregular distribution of metal powders of the powder layer is idealized as two-dimensional distribution in which metal powders are located regularly and periodically on the plate. In this study the design values of laser power vs scanning speed have been obtained. Temperature distribution and temperature variation of the powder layers with respect to time have been predicted. The commputed dsign data will be useful in determining the initial conditions of the process.