• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.154-157
• /
• 2009

Fuel cell is spotlighted as next energy source of future. The fuel of vehicle will be changed from fossil fuel such as gasoline, diesel to hydrogen. Polymer electrolyte membrane fuel cell(PEMFC) will be used to fuel cell vehicle because of its suitability. PEMFCs need oxygen for cathode. Because PEMFCs in vehicle use air for oxygen, air pollutant will be effect to performance of PEMFC. In this study, we examine a type of filter and pollutant gas how can be effect to performance of fuel cell electric vehicle.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.8 no.5
• /
• pp.30-35
• /
• 1999

Since LPG has a higher octane number and a lower maximum combustion temperature than gasoline it is getting more popular for reducing emissions from the vehicle This paper when an LPG engine works in the range of idle analyzed the operating range preciously an provides reducing method of emissions for the LPG engine. An electronic control unit(ECU) for the LPG engine using a feedback mixer is presented. The ECU is built by using a microcontroller MC68HC05. A PI-controller is imple-mented in the ECU in order to handle to handle Air/Fuel ration control. The experimental results exhibit that the required engine performance are satisfied at idle.

• Journal of Energy Engineering
• /
• v.11 no.1
• /
• pp.74-80
• /
• 2002

In this study, a numerical method for fuel droplet evaporation in cylinder of S.I. engine is presented. This study was newly defined non-dimensional critical droplet lifetime and modeled heating and evaporation processes of fuel droplet during intake and compression stroke of gasoline engine. The simulation results show that simultaneous increase of gas temperature and pressure in compression stroke seems to have compensative effect on droplet gasification rate. The environment variations in cylinder have little effect on the fuel droplet gasification process. The droplet size for full evaporation at the end of compression stroke can be estimated using this program.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.5
• /
• pp.1-8
• /
• 2002

For gasoline engines, a three-way catalytic converter that has the maximum efficiency at stoichiometric air/fuel ratio is used to clean up the exhaust gas. So a precise air/fuel ratio control is necessary to maximize the catalytic conversion efficiency, For a transient condition, a fred-forward air/fuel ratio control method that estimates the air mass inducted into a cylinder is being used. In this study, a fuel injection map that makes an accurate air/fuel ratio control possible was constructed for the very same transient condition. For the same condition above, intake air model and fuel model were refined so that fuel injection values based on air mass through a throttle valve and intake manifold pressure are equal to the map values.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.11 s.254
• /
• pp.1123-1130
• /
• 2006

This study discusses about research efforts of hydrogen generation from hydrocarbon(e.g., diesel, gasoline, natural gas, and LPG), especially, butane reforming by using Autothermal Reforming Reaction (ATR) technology. Several catalysts were selected for butane ATR. Thermodynamic reactor conditions (temperature, $O_2$/C, S/C) are varied and reforming characteristics of 2 catalysts (Pt and Rh on ceramic supports) and 1 commercial catalyst (FCR-HC35) have been examined. To understand reaction behaviors in an ATR reactor comprehensively, temperature profiles of reactor were observed. By mass transfer limitation, fuel conversion decreases when GHSV increases. Significant temperature variation along the reactor was observed and it was mainly due reaction kinetics difference between exothermic oxidation and endothermic reforming reaction.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.50-55
• /
• 2001

To simulate the combustion process under stratified charged conditions, like GDI engines, the new combustion model is proposed, which is based on Welter's FAE model and Peters' PDF model for considering primary reactions. In addition to these models, the new laminar burning velocity correlation and diffusion flame model are also included in the proposed model. The former can be applicable to much wider range of equivalence ratio, pressure and temperature than the others, such as Keck's and Guilder's models, and the latter has been derived from water-gas shift reaction and hydrogen oxidation, by which the secondary reactions can be considered after primary reactions. 3-D computation has been performed by using STAR-CD v3.05 in the simple cylindrical geometry under stratified charged condition. Judging from the calculated results, the present model proves to be reasonable to simulate the characteristics of flame propagation and concentrations of products in burned regions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.23-31
• /
• 2000

Knock and misfire, kinds of abnormal combustion, are highly undesirable effect on the internal combustion engine. So, it is important to detect these avnormal combuition and control the ignition timing etc. to avoid these mal-effect factors in real engine system. In this study, the system which detects the knock and the misfire using by spark plug is presented. This system is based on the effect of modulation breakdown voltage(BDV) between the spark gaps. The voltage drop between spark plug electrodes, when an electrical breakdown is initiated, depends on the temperature and pressure in combustion chamber. So, we can detect knock and misfire that produce changes in gas temperature and pressure (consequently, its density) using by BDV signal change which carries information about the character of combustion.

• Journal of the korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.75-86
• /
• 1986

This paper describes a simulation program of intake and exhaust processes in a 4-stroke S.I. engine and also studies the relationship among various engine parameters under different engine speed and load conditions. This simulation program includes the engine cylinder model for the intake and exhaust processes and its formulation and evaluates the system characteristics such as inlet mass, pumping work and residual gas in the cylinder-which influence on power output, fuel economy and exhaust emissions. In order to evaluate the accuracy of the simulation program, predicted results were compared with the experimental data obtained on the 4-stroke, 4-cylinder gasoline engine and satisfactory agreement was obtained.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.93-98
• /
• 2002

It is a present situation that the control on automobile emission is getting more restrictive and also the regulations for emission are changing greatly up to level of those advanced foreign countries. Specially, it has been many years that exhaust gases from gasoline automobile rather than from diesel is the major object concerned by Korea and other countries, and it is strongly required on the reduction techniques on harmful NOx and PM among those compositions. Thus, this research focused on the Exhaust Gas Recirculation (EGR) and the target fur this research is heavy-duty turbo-diesel engine with EGR, and conducted with numerical simulation to get engine performance and the characteristics of emission. Furthermore. the results obtained under different conditions such as rpm, power, EGR rate are compared and investigated with the numerical simulation using KIVA-3.

• 한국전기화학회:학술대회논문집
• /
• 2003.07a
• /
• pp.89-95
• /
• 2003

Fuel processing is an enabling technology for faster commercialization under lack of hydrogen infrastructures. It has been reported that the development of novel catalysts that are active and selective for hydrocarbon reforming reactions. It has been realized, however, that with pellet or conventional honeycomb catalysts, the reforming process is mass transport limited. This paper reports the development of catalyst structures with microchannels that are able to reduce the diffusion resistance and thereby achieve the same production rate within a smaller reactor bed. These microchannel reforming catalysts were prepared and tested with natural gas and gasoline-type fuels in a microreactor (1-cm dia.) at space velocities of up to 250,000 per hour. These catalysts have also been used in engineering-scale reactors (10 kWe, 7-cm dia.) with similar product qualities. Compared to pellet catalysts. the microchannel catalysts enable a nearly 5-fold reduction in catalyst weight and volume.