• The KSFM Journal of Fluid Machinery
• /
• v.19 no.6
• /
• pp.19-25
• /
• 2016

Anti-icing is important in gas turbines because ice formation on compressor inlet components, especially inlet guide vane, can cause performance degradation and mechanical damages. In general, the compressor bleeding anti-icing system that supplies hot air extracted from the compressor discharge to the engine intake has been used. However, this scheme causes considerable performance drop of gas turbines. A new method is proposed in this study for the anti-icing in combined cycle power plants(CCPP). It is a heat exchange heating method, which utilizes heat sources from the heat recovery steam generator(HRSG). We selected several options for the heat sources such as steam, hot water and exhaust gas. Performance reductions of the CCPP by the various options as well as the usual compressor bleeding method were comparatively analyzed. The results show that the heat exchange heating system would cause a lower performance decrease than the compressor bleeding anti-icing system. Especially, the option of using low pressure hot water is expected to provide the lowest performance reduction.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.2
• /
• pp.369-376
• /
• 2018

This paper presents an android-based implementation of real-time remote monitoring system for industrial gas turbines. The use of remote monitoring techniques can be beneficial in terms of not only the reduction of monitoring cost but also the earlier detection of abnormal status. In order to achieve the ability of protecting sensitive information from unauthorized persons, the proposed system supports secure transmissions using the RSA(Rivest Shamir Adleman) algorithm. In the event of abnormal situation on the gas turbine, the remote monitoring system generates an alarm to attract the user's attention by exploiting a push-message technique. The proposed system has been verified through a series of experiments with an experimental setup including a virtual data generator.

• The KSFM Journal of Fluid Machinery
• /
• v.20 no.2
• /
• pp.32-40
• /
• 2017

In this study, an in-house program to analyze the performance degradation for gas turbines is developed using MATLAB and is validated using commercial software. This program consists of design and off-design calculations. The results of design calculation is used for reference values of off-design calculation. The off-design calculation is composed of measured and expected performance analyses, and turbine inlet temperature correction. In general, performance degradation is analyzed by comparing the results of measured and expected performance analysis. However, if gas turbine performance degrades, turbine inlet temperature might increase due to the general control logic to comply with the power demand. Therefore, it is required to consider the deviation of turbine inlet temperature from the normal value in the performance diagnosis to analyze the performance degradation exactly. In this study, a special effort is given to the correction of turbine inlet temperature. The accuracy of the developed program is confirmed by comparison with commercial software, and its capability of performance diagnosis using the turbine inlet temperature correction is demonstrated.

• Advances in materials Research
• /
• v.8 no.1
• /
• pp.11-24
• /
• 2019

This paper presents a review study for energy-efficient gas turbines (GTs) with cycles which contributes significantly towards sustainable usage. Nonetheless, these progressive engines, operative at turbine inlet temperatures as high as $1600^{\circ}C$, require the employment of highly creep resistant materials for use in hotter section components of gas turbines like combustion chamber and blades. However, the gas turbine obtain its driving power by utilizing the energy of treated gases and air which is at piercing temperature and pushing by expanding through the several rings of steady and vibratory blades. Since the turbine blades works at very high temperature and pressure, high stress concentration are observed on the blades. With the increasing demand of service, to provide adequate efficiency and power within the optimized level, turbine blades are to be made of those materials which can withstand high thermal and working load condition for longer cycle time. This paper depicts the recent developments in the field of implementing the best suited materials for the GTs, selection of proper Thermal Barrier Coating (TBC), fracture analysis and experiments on failed or used turbine blades and several other designing and operating factors which are effecting the blade life and efficiency. It is revealed that Nickel based Superalloys were promising, Cast Iron with Zirconium and Pt-Al coatings are used as best TBC material, material defects are the foremost and prominent reason for blade failure.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.4
• /
• pp.399-407
• /
• 2011

This study analyzes the performance of hybrid power systems combining a solid oxide fuel cell (SOFC) and a gas turbine (GT). Research focus is given to the influence of the size-dependent gas turbine performance on hybrid system performance. Three hybrid systems adopting different gas turbines (kW, sub-MW, multi-MW classes) are designed. As the gas turbine power increases (i.e. as the gas turbine performance enhances), the gas turbine power portion increases and the hybrid system efficiency increases. The hybrid system shows efficiency improvement over the SOFC only system even in the case where the gas turbine net power is nearly zero. The increase of gas turbine pressure ratio contributes to the net hybrid system power output in all of the three cases, while system efficiency is almost independent on the pressure ratio.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.2314-2316
• /
• 2001

The steam gererator which produces thermal energy from coal or gas is a very important device in power plants, including the turbine driving synchronous generator which transforms kinetic energy into electrical energy. The turbine and the generator are driven by many kinds of media according to the types of which power plants are classified into steam turbine generator, gas turbine generator, water turbine generator and so on. This paper introduces the overspeed protection as well as the various speed and load control methods of some types of turbines.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.855-861
• /
• 2008

Micro wave rotor is expected to improve the performance of micro gas turbines drastically. In the present study, a micro wave rotor test rig was designed and built for micro gas turbines of 1-10 kW output range, and its test runs were carried out with cold air flow. In the previous experiments, the leakage loss had large influence on its operating condition. Therefore, abradable coating was applied on the end walls to achieve the operation with zero clearance for leakage reduction and its improvement on the operating condition is discussed in this study.

• International Journal of Computer Science & Network Security
• /
• v.22 no.12
• /
• pp.178-184
• /
• 2022

Renewable energy sources based on solar radiation, wind energy, geothermal energy, and biomass energy have now reached the level of industrial application. A new way to generate electricity using low-potential heat is to install a hydro-steam turbine. In hydro-steam turbines, hot water is supplied directly to turbine rotor nozzles without prior separation into steam and water in separators, which significantly increases the efficiency of hot water energy use. Such turbines are suggested to be used as autonomous energy sources in geothermal heating systems, heating water boilers and cooling systems of chemical reactors, metallurgical furnaces, etc. The authors conclude that the installation of hydro-steam turbines in heating plants and process boiler plants can also be effective if the used exhaust steam-water mixture at the turbine outlet is used to heat the network water or as return water.

• Journal of Energy Engineering
• /
• v.12 no.1
• /
• pp.1-10
• /
• 2003

Pressurized fluidized bed combustion unit is operated at pressures of 1~1.5 MPa with combustion temperatures of 850~87$0^{\circ}C$. The pressurized coal combustion system heats steam, in conventional heat transfer tubing, and produces a hot gas supplied to a gas turbine. Gas cleaning is a vital aspect of the system, as is the ability of the turbine to cope with some residual solids. The need to pressurize the feed coal, limestone and combustion air, and to depressurize the flue gases and the ash removal system introduces some significant operating complications. The proportion of power coming from the steam : gas turbines is approximately 80:20%. Pressurized fluidized bed combustion and generation by the combined cycle route involves unique control considerations, as the combustor and gas turbine have to be properly matched through the whole operating range. The gas turbines are rather special, in that the maximum gas temperature available from the FBC is limited by ash fusion characteristics. As no ash softening should take place, the maximum gas temperature is around 90$0^{\circ}C$. As a result a high pressure ratio gas turbine with compression intercooling is used. This is to offset the effects of the relatively low temperature at the turbine inlet.

• Journal of Technology Innovation
• /
• v.32 no.1
• /
• pp.1-25
• /
• 2024

Countries around the world are making active efforts to reduce greenhouse gas emissions. Korea is also pursuing a policy of abolishing aging coal power and converting it to LNG power generation. However, in Korea, gas turbine manufacturing technology has not been localized, so all of it is imported and installed from overseas manufacturers. Therefore, this paper examines the domestic and foreign environment of the gas turbine power generation industry and proposes a strategy to develop and expand the supply of Korean gas turbine technology by applying the PEST-SWOT-AHP methodology. As a result of the research, the strategy to develop and expand the supply of Korean gas turbine technology can be summarized as 1) strengthening the role of power generation public enterprises to develop and promote commercialization of gas turbine technology, 2) expanding the proportion of LNG power generation to reduce greenhouse gases, 3) the government's active efforts to create an ecosystem for the gas turbine industry, and 4) forming a public consensus on the construction of LNG power plants.