• Korean Journal of Materials Research
• /
• v.9 no.2
• /
• pp.111-116
• /
• 1999

The microstructure of vitreous bonded abrasives, which are used as the essential materials in the precise grinding, was investigated theoretically using two particle model. In this paper, a general equation applicable for a case in which there is a gap between abrasive grits is suggested. As a result, it was known that both the volume ratio of grit to glassy bond(V\ulcorner/V\ulcorner) and porosity(V\ulcorner) are the function of $\alpha$(the ratio of distance between grit to diameter of grit) and $\theta$(the angle from the center of pore to that of grit). Because the value $\alpha$ and $\theta$ can be get easily by using these suggested equations, the microstructure could be explained quantitatively. Also the raised error with the increasing amount of bond was modified by the simple assumption. As a result, in that case, both V\ulcorner/V\ulcorner and V\ulcorner were known to be the function of $\alpha$ and $\theta$(the ratio diameter of pore to that of grit).

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.500-503
• /
• 2002

In this paper, we demonstrate the deformation of TFT-LCD panel using numerical analysis based on the finite element method. To make better uniform cell gap and less stress at a photo-definable spacer (spacer), we have investigated process and design factors such as amount of liquid crystal (LC), spacer density, area, height, and material property. Furthermore we optimized design factors and achieved the robust design through the simulation.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.38 no.7
• /
• pp.549-556
• /
• 1989

Radiation induced current of the insulating oil used for X-ray tube housing was investigated in this paper. The X-ray induced current increased in proportion to the X-ray intensity and X-ray wave length and was greatly affected by the temperature of the insulating oil and the gap length` however, the current was not varied by the amount of the X-ray absorbed. The results suggest that one must consider the following problems as important factors for X-ray machine design and normal operation: cooling system of the X-ray tube housing, X-ray intensity, increasing temperature due to continuous operation, years used, and oil exchange and management.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.338-341
• /
• 2002

$(Ba_{1-x}Sr_{0.4}Ca_x)TiO_{3}$ (x=0.10, 0.15, 0.20) powders were prepared by the sol-gel method and BSCT thick films were fabricated by the screen-printing method. Their structural and dielectric properties were investigated with variation of composition ratio and $Al_{2}O_{3}$ doping contents. As results of the X-ray diffraction and microstructure analysis, the grain size of BSCT thick films was decreased with increasing $Al_{2}O_{3}$ amount. The thickness of BSCT thick films by 4-coating/drying is about $110{\sim}120{\mu}m$. The tunability increased with decreasing Ca content, and the BSCT(50/40/10) specimen doped with 1.0wt% $Al_{2}O_{3}$ showed the highest value of 12.94% at 5kV /cm.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05c
• /
• pp.114-117
• /
• 2001

$(Ba_{0.6-x}Sr_{0.4}Ca_x)TiO_3$(x=0.10, 0.15, 0.20) ceramics were fabricated by the mixed-oxide method and their structural and dielectric properties were investigated with variation of composition ratio and sintering temperature. As a result of the differential thermal analysis(DTA), exothermic peak was observed at around $1020^{\circ}C$ due to the formation of the polycrystalline perovskite phase. BSCT(50/40/10) specimen sintered at $1500^{\circ}C$ showed the highest average grain size(18.25$[{\mu}m]$). Curie temperature and dielectric constant at room temperature decreased with increasing amount of Ca. BSCT(50/40/10) specimen sintered at $1450^{\circ}C$ showed a good dielectric constant, K, (=4324) and dielectric loss, $tan{\delta}$, (=0.972%) properties at 1[KHz].

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.533-539
• /
• 2004

The rotary compressor is widely used for the air conditioner because it is efficient and compact. In recent, the need for silent and efficient compressors is much stronger than the past. The new type muffler was invented to reduce noise level and to improve efficiency. The new type muffler that has two side discharge holes and dome shape represents much lower overall noise level, especially noise levels around 1kHz than the old type one that has one center discharge hole In acoustic spectra. Also it has higher air conditioner efficiency by lower oil discharging amount of a compressor than old type one that has rectangular shape and two side discharge holes. The noise reduction and efficiency improvement effects of the new type muffler were verified by tests for rotary compressors and air conditioners.

• Proceedings of the KSR Conference
• /
• 2008.06a
• /
• pp.2011-2014
• /
• 2008

A linear induction motor for urban railway transit is accompanied with the end-effect and large air-gap comparing with a rotary induction motor. These cause amount of difference between simulation results and experiments. In order to figure out the difference, experiments based on a real-scale test bed are indispensable, however building a test-line and a test vehicle is so difficult that authors are going to make a small-scale model and simulate it for comparison. In this paper, A rotary-type small-scale model of a linear induction motor is designed. Thrust and normal force of the model have been analyzed with the variation of frequency and speed by using a Finite Element Method(FEM).

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.1
• /
• pp.292-300
• /
• 1995

According to the number of cold-rolled coils, the amount of roll wear and thermal expansion, and roll gap profile were calculated, by using the actual data from the finishing mill. Also, based on those data, the calculations of the deflection, the flattening, and the contact pressure of vwork rolls and backup rolls were made respectively. Specially, in the calculation of contact pressure, the numerical results were obtained not only during the normal rolling, but also during the abnormal rolling, by modeling mathematically the dynamic impact force which occurs when the head section of the strip is threading through rolls. With those results the growth of the fatigue region and the fatigue damage of rolls were predicted. Also the optimum roll-grinding depth was determined to maximize the roll life.

• The Korean Journal of Ceramics
• /
• v.3 no.1
• /
• pp.21-23
• /
• 1997

Dependences of total photoyields on incident photon energies were measured using synchrotron radiation light for different chemical-vapor-deposited diamond with differently treated surface. Results show that a considerable amount of gap states are presented for as-grown specimens with H-terminated, that negative electron affinity (NEA) is realized for H-plasma-treated specimens, and that sufficient O-treatment to NEA specimens results in positive electron affinity. The observed electron affinity can be explained in terms of differences in strength of the surface dipole layer formed by difference in the electron negativity among C, H and O atoms.

• Journal of the Korean Ceramic Society
• /
• v.26 no.2
• /
• pp.258-266
• /
• 1989

The effects of grain size and dopant ZnO on the photoelectrochemical conversion in TiO2 ceramic electrodes have been investigated. The photocurrent increases with increasing grain size in the undoped TiO2 ceramic electrode. In ZnO-doped TiO2 electrodes, the photocurrent decreases with increasing ZnO up to 0.4 wt% due to decrease of donor concentration, and then with further addition of ZnO, photocurrent increases according to the formation of second phase. However, the photoresponse appears at wavelength of 420nm, which is very close to the energy band gap of TiO2, regardless of grain size and amount of ZnO.