• Journal of the Korean Geotechnical Society
• /
• v.32 no.7
• /
• pp.47-56
• /
• 2016

In the case of excavating ground backfilled with soft ground, ground destruction occurs owing to the discharge of groundwater from excavated back ground in spite of earth retaining wall. To minimize this, indoor model test was implemented applying stabilizing pile as a solution for ground destruction. The unreinforced case was compared with the reinforced case and the comparison demonstrated that the ratio of the gap in settlement of the two cases is about three to one, which proves the reinforcement effect (Kim, 2014). This study has carried out the evaluation of appropriate pile spacing ratio, according to the confirmed effect of stabilizing pile. In the evaluation test the case with pile spacing ratio of 0.66 (5 stabilizing piles) was compared with that of 0.76 (3 stabilizing piles), and it has been shown that applying stabilizing pile has effect on ground destruction reduction, but may rather work as load when pile spacing ratio is narrower than a certain interval. So it was found that adjustment for appropriate pile spacing ratio is required at the stage of design. This study has shown that the pile spacing ratio is appropriate at around 0.7~0.8, which reduces ground destruction and does not function as the load of excavated back ground.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.154-154
• /
• 2003

A stoichiometric mixture of evaporating materials for CuGaSe2 single crystal thin films was prepared from horizontal electric furnace. Using extrapolation method of X-ray diffraction patterns for the polycrystal CuGaSe2, it was found tetragonal structure whose lattice constant at and co were 5.615 ${\AA}$ and 11.025 ${\AA}$, respectively. To obtain the single crystal thin films, CuGaSe2 mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the hot wall epitaxy (MWE) system. The source and substrate temperatures were Slot and 450$^{\circ}C$, respectively. The crystalline structure of the single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (UXD). The carrier density and mobility of CuGaSe2 single crystal thin films measured with Hall effect by van der Pauw method are 5.0l${\times}$10$\^$17/ cm$\^$-3/ and 245 $\textrm{cm}^2$/V$.$s at 293K, respectively. The temperature dependence of the energy band gap of the CuGaSe2 obtained from the absorption spectra was well described by the Varshni's relation, Eg(T) = 1.7998 eV - (8.7489${\times}$10$\^$-4/ eV/K)T$^2$/(T + 335 K. After the as-grown CuGaSe2 single crystal thin films was annealed in Cu-, Se-, and Ca-atmospheres, the origin of point defects of CuGaSe2 single crystal thin films has been investigated by the photoluminescence(PL) at 10 K The native defects of V$\_$CU/, V$\_$Se/, Cu$\_$int/, and Se$\_$int/ obtained by PL measurements were classified as a donors or accepters type. And we concluded that the heat-treatment in the Cu-atmosphere converted CuGaSe2 single crystal thin films to an optical n-type. Also, we confirmed that Ga in CuGaSe2/GaAs did not form the native defects because Ga in CuGaSe2 single crystal thin films existed in the form of stable bonds.

• Journal of the Korean earth science society
• /
• v.34 no.3
• /
• pp.189-194
• /
• 2013

In this study, the patterns of barotropic vortices and their structural rotation were investigated through laboratory experiments. Both stable and unstable barotropic vortices were formed in a rotating water tank with a rotating circular plate depending on the diameter, direction, and speed of rotating circular plate. The patterns of stable vortices turned out to be tripolar, triangular, rectangular, and monopolar vortex. These vortex patterns were affected by the gap between the circular plate and the wall of the water tank. Many unstable vortices were formed by anticyclonically and highly rotating circular plate. These results were caused by the centrifugal instability. The structural angular velocity of the tripolar vortex increased with the tangential velocity of the circular plate. The anticyclonic tripolar vortex had higher structural angular velocity than the cyclonic vortex. The tripolar vortex in the water tank was very similar with the real oceanic tripolar vortex from the view point of the Rossby number and the structural rotation.

• Journal of Korea Multimedia Society
• /
• v.11 no.3
• /
• pp.373-385
• /
• 2008

The evolution of input device for computer has pretty much slowed down after the introduction of mouse as feinting input device. Even though stylus and touch screen were invented later on which provide some alternatives, all these methods were designed to have close range interaction with computer. There are not many options available for user to interact with computer from afar, which is especially needed during presentation. Therefore, in this paper, we try to fill the gap by proposing a laser pointer interaction system to allow user to give pointing input command to the computer from some distance away using only laser pointer, which is cheap and readily available. With the combination of image processing based software, we could provide mouse-like pointing interaction with computer. The proposed system works well not only in currently plane screen, but also in flexible screen by incorporating the feature of non-linear coordinate mapping algorithm in our system so that our system can support non-linear environment, such as curved and flexible wall.

• Proceedings of the Korean Society of Medical Physics Conference
• /
• 2004.11a
• /
• pp.136-139
• /
• 2004

In this study, we used the rectal balloon to overcome the dose limit of the radiation therapy in the prostate cancer. Using the rectal balloon, we could minimize the planning target volume (PTV) by minimizing the internal motion of prostate and increased the gap between the rectum wall and the high dose region. To this purpose, we analyzed the position reproducibility of rectal balloon during the patient setup. Moreover, we studied the clinical feasibility of rectal balloon by performing the IMRT plan.

• Journal of Microbiology and Biotechnology
• /
• v.11 no.6
• /
• pp.1018-1023
• /
• 2001

Oleamide (cis-9-octadecenamide) is endogenous primary amide of fatty acid that is produced in small amounts in animal brains. It is known to induce sleep and to lower temperature by destroying the lipid plasma membrane structure of cells, thereby disclosing gap junction channels. To develop a new biological production method for oleamide, a screening program was conducted to isolate a microorganism producing oleamide. Among 1,500 soil microorganisms tested, KK90378 exhibited a potent positive reaction with Dragendoff`s reagent, used to detect the primary amide of oleamide. KK90378 was identified as a Streptomyces species based on cultural and morpohological characteristics, the presence of diaminopimelic acid in the cell wall, and the sugar patterns for the whole-cell extrat. Streptomyces sp. KK90378 produced oleamide 3 days after culture at $28^{\circ}C$, pH 7.2 A series of purification steps, including hexane extraction, silica gel column, and preparative thin layer chromatographies, were performed for the purification of oleamide. A spectrophotometric analysis using $^1H$, $^13C$-NMR, and GC-MS confirmed that the chemical structure of the purified oleamide was identical to that of authentic oleamide.

• Wind and Structures
• /
• v.30 no.5
• /
• pp.465-474
• /
• 2020

Vortex-induced vibrations of a yawed flexible cylinder near a plane boundary are numerically investigated at a Reynolds number Re_n= 500 based on normal component of freestream velocity. Free to oscillate in the in-line and cross-flow directions, the cylinder with an aspect ratio of 25 is pinned-pinned at both ends at a fixed wall-cylinder gap ratio G/D = 0.8, where D is the cylinder diameter. The cylinder yaw angle (α) is varied from 0° to 60° with an increment of 15°. The main focus is given on the influence of α on structural vibrations, flow patterns, hydrodynamic forces, and IP (Independence Principle) validity. The vortex shedding pattern, contingent on α, is parallel at α=0°, negatively-yawed at α ≤ 15° and positively-yawed at α ≥ 30°. In the negatively- and positively-yawed vortex shedding patterns, the inclination direction of the spanwise vortex rows is in the opposite and same directions of α, respectively. Both in-line and cross-flow vibration amplitudes are symmetric to the midspan, regardless of α. The RMS lift coefficient C_L,rms exhibits asymmetry along the span when α ≠ 0°, maximum C_L,rms occurring on the lower and upper halves of the cylinder for negatively- and positively-yawed vortex shedding patterns, respectively. The IP is well followed in predicting the vibration amplitudes and drag forces for α ≤ 45° while invalid in predicting lift forces for α ≥ 30°. The vortex-shedding frequency and the vibration frequency are well predicted for α = 0° - 60° examined.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.52 no.2
• /
• pp.67-73
• /
• 2010

Unlike Urban building, horticultural facilities has a lot of heat loss through plastic or glass covering material which could be much influential to growing plant and consuming energy for heating greenhouse. In many cases, heat loss from a break of cover, a gap of joint sealing, the entrance to greenhouse and windows for ventilation are the main factors considered in calculating the heating load for horticultural facilities. however the normal observation through human eye and digital camera could not recognize where the heat loss occurred. but the infrared thermal image camera with detecting thermal difference could be very effective for noticing heat loss by analyzing infrared thermal image. In this study, greenhouse structure, covering material, internal and external provisions for Horticultural facilities were surveyed in different sites and Infrared thermal camera shooting and image analysis were performed for auditing heat loss from cultivation facilities The results from this study were that unexpected heat loss had been noticed in 7 representative cases of greenhouse such as side wall covered with single or double plastic, and the joint of horizontal thermal curtain, roof without horizontal thermal curtain, entrance to greenhouse, windows for ventilation. the most important factors for keeping heat energy were whether the horizontal thermal curtain with multifold thermal material was installed or not. The internal or external covering using multifold thermal curtain proved to be the most effective ways to keep heat energy from losing through heat transmission, heat radiation. from inside to outside the horticultural facilities.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.59-60
• /
• 2018

In this paper, we studied a design method for a band-pass waveguide filter with a modified H-type resonant iris (RI) placed in a thin transverse wall of a rectangular waveguide. The horizontal straight gap at the center of a conventional H-shaped iris is modified to a U-shaped one to increase the equivalent capacitance, and the equivalent inductance is improved by changing the vertical two straight slots into C-shaped ones. A third-order band pass filter using the proposed modified H-shaped iris was designed and, it was observed that the filter operated in the frequency range of 9.22-9.75 GHz with its insertion loss of 0.5 dB and return loss of 17 dB.

• KIEAE Journal
• /
• v.13 no.6
• /
• pp.121-128
• /
• 2013

This study attempted to explore the MC design methods of modular construction using discontinuous double module grids and further, the design methods of walls. Modular construction is generally characterized with multiple units called modules with a module dimension of 3M(300mm) appearing in the form of double grids. The discontinuous double grids including correction values and gap values occurs inevitably in the modular construction where units are joined horizontally. Therefore, it is desirable to carry out the MC design taking into account these discontinuous double grids. In this study, the MC design was applied to the plane of wooden houses in modular construction, going through a process of setting the size of pillars and inside dimensions, of determining the dimension of discontinuous double grids that occur during the assembly of units, and of setting the dimension of outer walls in conjunction with the derived dimensions. The dimension of outer walls was applied differently depending on the range of regional use by analyzing the energy performance with the materials used. Consequently, the materials and components of factory-produced buildings can be used directly without processing, and the suitability of the outer wall design can be pre-determined by previewing the calculation of the cross-sectional configuration and heat transmission coefficients of outer walls in modular construction, allowing to be used as a decision-making tool of design.