• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.968-970
• /
• 2001

Recently, the power supply equipments have tendency to take multiple feedback loop paths. In this paper the state space averaging technique is applied for the analysis of flyback type current mode control circuit. We made real converter for the gurantee of stable output characteristic and proper design of feedback circuit. The validity of proposed method is verified from test results. The improvement of stability is confirmed by sinusoidal signal injection method with isolated transformer. It is known that phase margin is sufficient and gain crossover frequency $f_c$ is nearly 1/5 of switching frequency $f_s$, from the experimental result with frequency response analyzer.

• ETRI Journal
• /
• v.31 no.3
• /
• pp.318-320
• /
• 2009

A switchable Yagi-Uda antenna prototype with radiation pattern reconfiguration is presented in this letter. The proposed reconfigurable antenna is based on the concept of switching between the reflector and director of a Yagi-Uda antenna using a radio frequency PIN diode. As a result, the minimum/maximum radiation can be steered towards desired signals or away from interfering signals in opposite directions. The measured 10 dB impedance bandwidth and gain are 210 MHz (7%) and 8.02 dBi at 3 GHz, respectively. Details of the antenna design and its performance are described and empirically analyzed.

• Proceedings of the KIPE Conference
• /
• 1998.11a
• /
• pp.55-59
• /
• 1998

By this time, Diode Rectifier or SCR has been used to gain DC Voltage for Electrolysis Power. Generally DC Voltage is produced from rectifier shall be transformed before rectifier using step-down transformer to obtain adaptable DC Voltage, rectifier output. In the same way, rectifier using SCR shall obtain output voltage after step-down voltage through transformer and control of the SCR firing angle. Transformer shall be used for this two methods to adjust the voltage. But the size and weight of the transformer are increased in accordance with the increase of capacity, and the hardships are accompanied in workspace or transportation. Besides, only the value of input voltage is possible to be regulated, and the expectation of current control is almost impossible during Electrolysis. This study has conducted Design and Simulation to reduce the size and weight of transformer and to be enable voltage and current control of Electrolysis power through high-speed switching using Inverter, Electronics device.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.1
• /
• pp.64-69
• /
• 2003

There exist the high frequency components, which can not be predicted by the low frequency model, due to the presence of sampling effect in current mode control. In this paper, the output voltage equations for the ZVS half bridge PWM convertor are derived from the steady state analysis, and the sampling gain presented in the current control loop is Investigated to improve the Prediction Performance of low frequency model of ZVS half bridge PWM converter.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.4
• /
• pp.71-77
• /
• 1998

In this paper, algeration of electical characteristics is analyzed when the operating temperature of MOSFET, BJT and CMOS/BiCMOS inverter is lowered from 300K to 77K. As the operating temperature is lowered, electric characteristics of MOSFET are enhanced generally but, those of bipolar transistor are degraded because current gain is reduced by BGN(Band Gap Narrowing) effect. For the inverter considered in this work, switching characteristics of PSA-BiCMOS inverter are enhanced by the electrical characteristics enhancement of MOSFET when the operating temperature is reduced to 200K, while under 200K, those of PSA-BiCMOS inverter are degraded because the degradation of BJT impacts on the inverter circuit.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.7
• /
• pp.819-825
• /
• 1988

An 1-bit DPCM image coding method is presented. Our method is specially designed to reduce the slope overload which seems to be the major performance degradation factor in 1-bit DPCM. In the present algorithm, based on the classification of neighborhoods by its flatness, slope strength and direction, predictor and quantizer operate adaptively through switching action. Compared with some other methods by computer simulation, proposed method shows improved performance in image quality as well as in signal to noise ratio. This gain mainly comes from the reduced slope overload and seems large to compensate the increased complexity in prediction. As a post processing, Lee filter is used to reduce the granular noise subjectively annoying in flat region.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.360-363
• /
• 2002

In the resonant converters which can provide high efficiency and high power density, the resonant voltage stress is about $4\~5$ times the input voltage. It needs the power switch with high ratings. This is a reason why the conduction loss is increased. In this paper, it proposes the alternately zero voltage switched forward, flyback multi resonant converter topology for reducing the voltage stress using alternately zero voltage switching technique. And the proposed AT forward MRC Is experimentally considered about the loop gain with HP4194A network analyzer

• Proceedings of the KIPE Conference
• /
• 2003.11a
• /
• pp.36-40
• /
• 2003

On analyzing the power circuit of a DVR system, control limitations and control targets are presented for the voltage compensation in DVRs. The control delay in digital controllers increases the dimension of the system transfer function one degree higher which makes the control system more complicate and more unstable. Based on the power stage analysis, a novel controller for the compensation voltages in DVRs is proposed by a feedforward control scheme. Proposed controller works well with the time delay in the digital control system. This paper also proposes a guide line to design the control gain, appropriate output filter parameters and inverter switching frequency for DVRs in digital controllers. Proposed theory is verified by an experimental DVR system with a typical digital controller.

• Journal of Power Electronics
• /
• v.13 no.4
• /
• pp.584-591
• /
• 2013

In this paper, a hybrid booster power module with Si IGBT and Silicon Carbide (SiC) Schottky Barrier Diode (SBDs) is presented. The switching characteristics of the hybrid booster module are compared with commercial Silicon IGBT/Si PIN diode based modules. We applied the booster power module into a non-isolated on board vehicle charger with a simple buck-booster topology. The performances of the on-vehicle charger are analyzed and measured with different power modules. The test data is measured in the same system, at the same points of operation, using the conventional Si and hybrid Si/SiC power modules. The measured power conversion efficiency of the proposed on-vehicle charger is 96.4 % with the SiC SBD based hybrid booster module. The conversion efficiency gain of 1.4 % is realizable by replacing the Si-based booster module with the Si IGBT/SiC SBD hybrid boost module in the 6.6 kW on-vehicle chargers.

• Journal of Institute of Control, Robotics and Systems
• /
• v.7 no.4
• /
• pp.288-294
• /
• 2001

In this study, a new PWM method considering the actuation delay of high speed solenoid valves is proposed to improve the response characteristics of electro hydraulic servo systems controlled by high speed solenoid valves. In addition, the decision method for the system gain, the basic period of PWM, and the sampling time is proposed, Since the conventional system controlled by high speed solenoid valves is too slow to apply this method, a high speed driving circuit(Quick-Drive) which enables rapid switching of the high speed solenoid valve at a high speed sampling mode is applied to realize this method. The experimental result shows that it is possible to achieve precision and quiet control without occurrence of limit cycle and wide range dead band.