• Bulletin of the Society of Naval Architects of Korea
• /
• v.26 no.1
• /
• pp.46-62
• /
• 1989

This paper presents the results of full-scale structural measurements of 4,800 unit pure car carriers "HYUNDAI NO.103" and "HYUNDAI NO.105" on one voyage respectively for each ship, especially in order to investigate the local strength of partial bulkhead above free-board deck. With the measured data, the short-term frequency analyses have been performed. The results show that the wave-induced stresses follow, on the whole, well the Rayleigh distribution. In addition, it has been found from the measured data that transverse local stresses at bulkhead section have a very close relation with the acceleration in athwartship direction. Finally, the long-term analysis has been attempted by using the following two statistical distributions mainly in order to estimate the maximum stress amplitude at the corners of partial bulkhead. 1) Exponential distribution of cycles of stress amplitude 2) Double exponential distribution of extreme values of stress amplitude for each short-term analysis The results of these two cases show a good agreement with each other. For example, the estimated maximum stress amplitude for 10 years at port-side corner of Fr. 132 partial bulkhead is $2125kg/cm^2$ for the first case and $2170kg/cm^2$ for the second case just based on the measured data.

• International Area Studies Review
• /
• v.15 no.3
• /
• pp.239-261
• /
• 2011

The cyclicality of productivity has been one of the essential issues in macroeconomics. Since Solow(1957) developed the dominant approach to the measurement of productivity growth, Solow's approach, which assumes the perfect competition, the constant returns to scale, and the full use of input factor has been modified particularly in Hall's(1990) and Basu's(1996) works. Their researches take account of market power, returns to scale, and variable factor utilization. This paper establishes the empirical model based on Hall's(1990) and Basu's(1996) models, estimates 4 types of Solow's reidual in manufacturing and 2 service industries over the period 1975:1-2010:4, and analyzes the cyclicality of measured productivity. The result proved the measured productivity to be procyclical in manufacturing industries and electricity and water industry, and in contrast to the Basu's, the variable factor utilization transformed the countercyclicality of measured productivity into its procyclicality in the Korean economy.

• Korea Journal of Hospital Management
• /
• v.8 no.3
• /
• pp.49-71
• /
• 2003

The purpose of the study is exploring the relationship among patient perceived quality of dental care, satisfaction, and royalty in dental clinics and hospitals. The observation of the study is outpatient visiting dental clinics and hospitals located in Seoul and Kyung-Gi Do area, and surveyed the outpatients. The contents of the survey are consisted with questions including quality of care perceived by the patients, costumer satisfaction, and royalty, and measurement for each question is using five point Likert scale. According to result of bi-variate analysis, there was the significant relationship among specialized care, value of the care, and kindness in quality of dental services, level of care in dentists significantly influenced on costumer satisfaction and costumer royalty, and there was the significant relationship between costumer satisfaction and royalty. According to result of regression analysis on the costumer satisfaction, the costumer satisfaction positively related with the convenience of facility, specialized care, value of care, patient age, number of visit, and spend time for treatment, and housewives and self-employees were likely to satisfy on care than regular employees. By result of full regression model and reduced model on costumer royalty, satisfaction could explain 86% on the costumer royalty such as re-visit and promoting other people, and increase of explain power is not significant when other independent variables joined model (full model). Considering efficiency of model, costumer royalty could be explained by satisfaction only rather than other independent variables used. Finally, This study shows that the social-demographic variables of patient influenced the patient satisfaction, and the patient satisfaction influenced patient royalty directly.

• Ecology and Resilient Infrastructure
• /
• v.8 no.2
• /
• pp.88-96
• /
• 2021

In surface image velocimetry, a wide area of a river is photographed at an angle to measure its velocity, inevitably causing image distortion. Although a distorted image can be corrected into an orthogonal image by using 2D projective coordinate transformation and considering reference points on the same plane as the water surface, this method is limited by the uncertainty of changes in the water level in the event of a flood. Therefore, in this study, we developed a tilt image correction technique that corrects distortions in oblique images without resetting the reference points while coping with changes in the water level using the geometric relationship between the coordinates of the reference points set at a high position the camera, and the vertical distance between the water surface and the camera. Furthermore, we developed a distortion correction method to verify the corrected image, wherein we conducted a full-scale river experiment to verify the reference point transformation equation and measure the surface velocity. Based on the verification results, the proposed tilt image correction method was found to be over 97% accurate, whereas the experiment result of the surface velocity differed by approximately 4% as compared to the results calculated using the proposed method, thereby indicating high accuracy. Application of the proposed method to an image-based fixed automatic discharge measurement system can improve the accuracy of discharge measurement in the event of a flood when the water level changes rapidly.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.20 no.2
• /
• pp.122-130
• /
• 2016

The past few decades of industrialization enabled human-centered stream developments, which in turn resulted in constructing straight or covered streams, which are used only for sewage disposal purpose. However, these types of streams have become the cause of flood damages such as localized heavy rain. In response, various construction methods have been implemented to prevent stream and embankment damages. However, regulations regarding these measures only lay out minimum standards such as the height of slopes and the minimum angle of inclination. Moreover, examination of tractive force, the most crucial factor in preventing flood damage, is nonexistent. Therefore, this study evaluates various tractive forces by implementing a porous concrete tetrapod at a full scale artificial stream for experiment, controlling the rate of inflow, and measuring the velocity and depth of the stream under different experiment conditions. The test results of the compressive strength, and porosity and density of rock of the porous concrete tetrapod was between 16.6 and 23.2 MPa, and the actual measurement of air void was 10.1%, thus satisfying domestic standard. The result of tractive force experiment showed a limiting tractive force of $47.202N/m^2$, not satisfying the tractive force scope of $67N/m^2$ the stream design working expertise proposes. However, there was neither damage nor loss of blocks and hardpan. Based on previous researches, it can be expected that there will be resistance against a stronger tractive force. Therefore, it is necessary to conduct another experiment on practical limiting tractive force by adjusting some experimental conditions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.2
• /
• pp.130-134
• /
• 2019

In this paper, a laser-based non-contact load cell is newly developed for measuring forces in prestressed concrete tendons. First, alumina particles have been sprayed onto an empty load cell which has no strain gauges on it, and the layer has been used as a passive stress sensor. Then, the spectral shifts in fluorescence spectroscopy have been measured using a laser-based spectroscopic system under various force levels, and it has been found that the relation of applied force and spectral shift is linear in a lab-scale test. To validate the field applicability of the customized load cell, a full-scale prestressed concrete specimen has been constructed in a yard. During the field test, it was, however, found that the coating surface has irregular stress distribution. Therefore, the location of a probe has to be fixed onto the customized load cell for using the coating layer as a passive stress sensor. So, a prototype customized load cell has been manufactured, which consists of a probe mount on its casing. Then, by performing lab-scale uniaxial compression tests with the prototype load cell, a linear relation between compression stress and spectrum shift at a specific point where laser light had been illuminated has been detected. Thus, it has a high possibility to use the prototype load cell as a force sensor of prestressed concrete tendons.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.350-358
• /
• 2012

This paper deals with accuracy of accumulated fatigue damage estimation using stochastic fatigue analysis method based on Rayleigh PDF. From full scale measurement data on an 8100TEU container vessel, zero-order spectral moments for wave- and vibration-induced energy spectral densities are determined on the probability level of 99%. 80 simulation cases in total are prepared according to the variation of ratio of zero-order spectral moments and center frequency of vibration ESD. By using inverse Fourier transformation and rainflow cycle counting for the combined ESD of wave and vibration, exact fatigue damages are derived. Fatigue damages in frequency domain based on Rayleigh PDF show large conservativeness compared to exact fatigue damages in times domain. The main cause of the excessive conservativeness is analyzed by two aspects: ratio of zero crossing and peak frequencies and ratio of initial zero order spectral moments and zero order spectral moments from rainflow stress range distributions. Finally, a guideline of applicability of Rayleigh PDF is proposed for wide band processes.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.359-366
• /
• 2012

This is the final one of the two companion papers dealing with accuracy of accumulated fatigue damage estimation under wide band process. It is stated that four kinds of wide band models exist: typed of equivalent stress, combined PDF, correction factor, and damage combination. For the idealized ESDs from full scale measurement data on an 8100TEU container vessel, fatigue damages are compared for a narrow band prediction model based on Rayleigh PDF and five wide band fatigue prediction models of Dirlik, Wirsching-Light, Jiao-Moan, Benasciutti and DNV. DNV model consistently overestimates fatigue damages regardless of variation of ESDs. Predictions by Jiao-Moan model, which is understood as standard method for design of offshore platforms, are also in conservative side. Best accuracy is found from the results by Dirlik and Benasciutti models, but Benasciutti model is preferred since it can easily combined with narrow band fatigue damage based on Rayleigh PDF.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.14 no.4
• /
• pp.264-272
• /
• 2011

Shipbuilders carry out the operation test to check the conditions of the main propulsion system and auxiliaries for moored vessel in the quoy before the sea trial. The estimation of the thrust and torque for the partially submerged propeller should be prepared to ensure the safety of mooring line and the ship. In this paper, the variations of the thrust and torque according to the shaft submergence and the propeller rotating speed in bollard pull condition are investigated with the model test and the numerical analysis. Based on these resaearch, the empirical formula representing the physical phenomena of the partially submerged propeller is derived and validated through comparison to measurement results of full-scale propellers under the quoy operation test.

• Management & Information Systems Review
• /
• v.1
• /
• pp.333-362
• /
• 1997

Since the profess of the reformation and opening Policy in 1978, China has been outstandingly developed its economy and increased the real scale of its economy 4 times as big as before, and is expected to rise as a superpower holding in check U.S.A even in economy as well as politics, military affairs and diplomacy in the 21st century. In this position, China has constantly tried to join WTO since 1986, as an effort to gain a status in the international society. It hsa been making various economic reformations to provoke a crustal movement in its own economy such as tariffs lowering measurement for the almost whole items, remove of restriction of import items, lowering the refunding rate of over deposit tax and annihilation of the special treatments for the foreign investment. In short, recently Chinese government is cutting down the special treatments for the foreign capital enterprises and changing the policy to the direction of gradually reinforcing the control, so it requires that our enterprises trying to advance and invest in China have to consider these carefully. Investment in China of our enterprises become serious since 1990 is focused on such labor intensive industries as textiles, sewing and shoes which lost the competitive power due to the wage increase. Particularly, Pusan economy having played the role of locomotive for Korean economy in the past developing period has been weakened in the competitiveness and not yet activated in 1990s. In terms of this, the enterprises engaged in such typical industries of Pusan as shoes, textiles and sewing have borne much fruit from the investment in China with abundant and cheap labors. However, from a few years the enterprises in Pusan invested in China due to the cheap labors and rich resources and invested in China have suffered much troubles and failures more and more resulted from the advancement without sufficient previous knowledge and information related to the investment including investment environment. Therefore, at the time of advancement in China, Korean enterprises should make their decision related to the investment, after taking these investment environment into account previously to a full extent and making an investment strategy.