• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.472-477
• /
• 2003

This study was performed to investigate the behavior of vapor phase of fuel mixtures with different piston cavity diameters in a optically accessible engine. The images of vapor phases were measured in the motoring engine using exciplex fluorescence method. The conventional engine was modified as GDI engine with swirl flow. Fuel was injected into atmospheric nitrogen to prevent quenching phenomenon by oxygen. Injection pressure is 5.1MPa. Two dimensional spray fluorescence image of vapor phases was acquired to analyze spray behavior and fuel distribution inside of cylinder. Three injection timings were set at BTDC $180^{\circ}$, $60^{\circ}$and $60^{\circ}$. With a fuel injection timing of BTDC $60^{\circ}$, fuel-rich mixture was concentrated in near the cavity center. With a fuel injection timing of BTDC $60^{\circ}$, fuel-rich mixture level in the center region was highest in the S-type during the late compression stroke. With a fuel injection timing of BTDC $180^{\circ}$, fuel was not affected in a piston cavity and generally distributed as homogeneous mixture.

• 한국산학기술학회논문지
• /
• 제15권5호
• /
• pp.2573-2578
• /
• 2014

본 연구는 4실린더 커먼레일 디젤 기관에서 바이오 디젤 혼합 연료를 사용하여 예비 분사시기와 EGR율을 변화시켰을 때 연소 압력과 배기 특성에 미치는 영향을 조사하기 위하여 실험을 수행하였다. 예비 분사 시기와 EGR율은 디젤 기관의 연소 및 배기 배출 특성에 큰 영향을 미친다. 본 연구에서는 일반적으로 많이 사용되고 있는 기관 회전 속도 2,000rpm에서 바이오 디젤 혼합율 20%의 연료를 사용하여 예비 분사 시기와 EGR율에 다양하게 변화를 주어 실험을 하였다. 실험결과, 도시 평균 유효 압력은 예비 분사 시기가 상사점전 BTDC $10^{\circ}$에서 가장 높았으며, 연소 압력과 열 발생율은 동일 예비 분사 시기에서 EGR율에 비례하여 감소하였다. NOx배 출량은 예비 분사시기에 관계없이 EGR율이 증가할수록 큰 폭으로 감소하였으며, 매연(Soot)은 예비 분사 시기 BTDC $20^{\circ}$에서 가장 적게 배출되었다.

• 한국분무공학회지
• /
• 제6권3호
• /
• pp.32-37
• /
• 2001

The characteristics of engine performance with fuel injection system in D.I. diesel engine were studied in this paper. A fuel injection system has an important role in the performance and emission gas in a diesel engine. In this paper, an experimental study has been performed to verify the effect of the performance and the emission gas with the factors such as diameters of an injection nozzle hole, diameters of an injection pipe and injection timing in the fuel injection system. The authors have obtained the results that optimizing the factors of fuel injection system is significant to enhance the performance of the engine system and consumption ratio of fuel, smoke, and NOx.

• Journal of Advanced Marine Engineering and Technology
• /
• 제36권5호
• /
• pp.603-608
• /
• 2012

요즈음 환경오염 문제와 대체에너지 문제에 관심이 증대되고 있다. 디젤기관은 일반적으로 육상과 해상에서 동력을 생산하는데 사용되고 있는데, 디젤기관의 연소특성과 배기배출물 특성은 기관의 운전시간이 증가함에 따라 연료계통의 마모와 연소실 주위상태의 변화로 달라진다. 본 논문은 약 20여년 사용한 디젤기관에 바이오디젤혼합유를 사용할 경우, 연소특성과 배기배출물 특성에 미치는 연료분사시기의 영향을 고찰하기 위하여 실험적으로 연구하였다. 실험기관의 원래 연료분사시기는 BTDC $22^{\circ}$ CA이었는데, 20여년 운전한 후에 연료소비율과 배기배출물 특성에 대하여 실험적으로 최적의 연료분사시기를 분석한 결과, BTDC $26^{\circ}$ CA로 변경되었음을 알았다.

• 소음진동
• /
• 제7권6호
• /
• pp.909-918
• /
• 1997

Combustion oriented noise is a part of engine noise, which is mainly determined by the in-cylinder pressure profile and the structure attenuation of an engine. A numerical model for predicting the in-cylinder pressure profile and the resultant combustion noise developed by the use of a commercial code. The model is experimentally validated and updated based on the performance as well as the noise by considering the fuel injection timing, the fuel injection rate, Cetane number, intake temperature, and compression ratio. For providing a design guide of a fuel injector for a low combustion noise engine model, the optimal parameters of injection pressure profile, injection rate profile, and injection timing are determined, which gives the 5 dBA noise reduction.

• 한국자동차공학회논문집
• /
• 제20권3호
• /
• pp.45-51
• /
• 2012

This work was investigated 2-stage injection strategy on combustion and emissions in a direct injection compression-ignition engine fueled with DME. Single cylinder engine was equipped with common rail. Injection pressure was 700bar, dSOI between the main injection and the pilot injection was varied. Diesel was used as compared fuel of DME in all cases. The results was shown that maximum pressure was higher than all cases and its amount of DME and diesel was similar. Regardless the pilot injection, the main fuel injection timing was same. The heat release rate of the main injection for diesel was high while that of pilot injection for DME was high. The THC was very low regardless of the fuel type and injection strategy. In the single injection, NOx was increased to retard of main injection timing regardless of the fuel type. NOx emissions was decreased with the retardation of the main injection timing regardless of the fuel type in the case of 2-stage injection strategy.

• 한국산업융합학회 논문집
• /
• 제19권3호
• /
• pp.154-159
• /
• 2016

Recently it has been focused that the automobile engine has developed in a strong upward tendency for the use of the high viscosity and poorer quality fuels in achieving the high performance, fuel economy, and emission reduction. Therefore it is not easy to solve the problems between low specific fuel consumption, and exhaust emission control at automotive engine In this study, it is designed and used the test bed which is installed with fuel injector controller. In addition to equipped engine using CRDI by controlling the injection timing with modulator, it has tested and analyzed the engine cycle variation characteristics, as it is varied that they are the operating parameters: fuel injected quantity, injection timing, engine speed and scavenging pressure.

• 한국자동차공학회논문집
• /
• 제22권7호
• /
• pp.98-106
• /
• 2014

Emission standards for passenger diesel engines are becoming more and more stringent. Especially, Europe started the regulation of nano-particles from 2011 with EURO 5b. The objective of this study is to investigate the effect of fuel injection strategy on combustion and nano-particle emission in a small diesel engine. In this study, we conducted combustion analysis and measured both the weight of PM and number of nano-particels. At first, the optimum injection timing was determined with fixed engine operating conditions, such as engine speed, load, and fuel injection quantity. After that, the injection timing was controlled, and the effect of pilot injection was investigated. The number of nano-particles increased as engine load decreases, and it increased up to 10 times depending on the change of injection timing. The weight of PM emissions was increased at low load, and the PM emissions increased with increasing the number of pilot injections.

• 한국분무공학회지
• /
• 제6권1호
• /
• pp.1-8
• /
• 2001

Fuel injection system is very important in diesel combustion. Recently electronic control of fuel injection system and common rail systems are introduced to reduce the emission and to increase the energy efficiency from diesel engine by control of the injection timing and duration. In this study, evaluation possibility of the system for electronic control by spool valve, one of the accumulator type injection systems with spool valve using solenoid was composed and the operating characteristics were investigated to evaluate the effects of spring coefficient, initial spring force, solenoid driving time, fuel supply pressure on the injection timing and duration. We could confirm the capability that diesel injection was electronically controlled by spool valve.

• 한국자동차공학회논문집
• /
• 제4권6호
• /
• pp.196-204
• /
• 1996

The simplified dynamic models of the timer assembly in the diesel engine fuel injection system were developed. The first order system with time delay was assumed and the various parameters in this model were obtained by experimental data. These simplified dynamic models were used for the development of control algorithm of the injection timing control system. The PI control algorithm was modified to include the anti-windup property and disturbance compensation. This modified PI control algorithm was used for the control of the injection timing. Improved control accuracy and reduced control efforts were observed.