• Nuclear Engineering and Technology
• /
• 제50권2호
• /
• pp.259-267
• /
• 2018

Focused ion beam-scanning electron microscope and electron backscattered diffraction examinations were conducted in the center of a $73\;GWd/t_U\;UO_2$ fuel. They showed the formation of subdomains within the initial grains. The local crystal orientations in these domains were close to that of the original grain. Most of the fission gas bubbles were located on the boundaries. Their shapes were far from spherical and far from lenticular. No interlinked bubble network was found. These observations shed light on previous unexplained observations. They plead for a revision of the classical description of fission gas release mechanisms for the center of high burn-up $UO_2$. Yet, complementary detailed observations are needed to better understand the mechanisms involved.

• 한국자동차공학회논문집
• /
• 제11권3호
• /
• pp.7-12
• /
• 2003

Mixture formation in the cylinder of a lean bum engine has been observed by Laser Induced Fluorescence technique. XeCl laser (308nm) was used to produce a laser sheet. 3-pentanone has been added to iso-octane fuel to produce fluorescence, the intensity of which is proportional to the concentration of the fuel. The laser sheet was introduced through the piston window and the fuel distribution in the vertical plane was observed through a side window. Comparison has been made for the cases of selected fuel injection timing as 0, 360, 405, and 450 CA. For the case of 0 and 360 CA injection, uniform fuel distribution in the combustion chamber has been obtained at the ignition time which is favorable for the high load mode. And the late injection cases, 405 and 450 CA, revealed the stratified formation of rich mixture around the spark plug. That extends the lean misfire limit and reduces cyclic variation in the low load mode.

• 방사성폐기물학회지
• /
• 제13권2호
• /
• pp.141-154
• /
• 2015

경수로 사용후핵연료 수송/저장용기의 핵임계 해석은 사용후핵연료내의 악티나이드핵종 및 핵분열생성물 함유량에 대한 불확실성을 이유로 신연료로 가정된 가상의 연료를 선정하여 평가해오고 있다. 그러나 이러한 평가방법은 용기 설계 시 과도한 임계여유도를 유도하여 경제적 손실을 유발할 수 있는 단점이있다. 이와 같은 단점을 극복하기 위하여 최근 연소도이득효과(burnup credit, BUC)를 반영한 수송저장용기의 설계 및 상용화를 위한 연구가 추진되었다. 이에 본 연구에서는 한국원자력환경공단에서 개발중인 금속겸용용기를 대상으로 연소도 이득효과적용 시 핵임계 안전성(criticality safety)에 영향을 미칠 것으로 예상되는 '노심 운전인자', '축방향 연소도 분포', '오장전 사고상황'에 대하여 핵임계 평가를 수행하였다. 그 결과 노심운전인자 중 저농축, 고연소도일 때 비출력에 따른 핵임계 변화가 크게 평가되었으며, 고연소도 사용후핵연료에서 End effect가 양의 값을 나타내었다. 특히 오장전에 의한 유효증배계수는 최대 0.18467증가하였으므로, 연소도이득효과를 적용 할 경우 필수고려사항임을 확인하였다. 본 연구결과는 국내모델(금속겸용용기)의 연소도 이득효과 적용기술 개발 및 사용 후핵연료 장전 시 일어날 수 있는 오장전 사고를 방지하기 위한 운영절차 개발에 참고자료로 활용될 수 있다.

• 대한기계학회논문집
• /
• 제17권6호
• /
• pp.1633-1639
• /
• 1993

본 연구에서는 급속연소기술의 가솔린엔진에 적용을 목적으로 흡입과정시 강한 와류(swirl)를 생성하는 마스크부착 헤드(masked shroud head, MSH)형을 급속연 소형으로 제작하여 마스크부착 헤드형에서의 급속연소효과를 이온전류법에 의한 화염 속도를 측정하므로서 규명하려한다. 이온전류는 이온탐침계(ion probe)를 연소실 표면의 두 지점에 설치하여 검출하며, 이온전류 신호를 정성적인 방법으로 검증한 후 표준 헤드형과 마스크부착헤드형을 장착한 엔진에 대해서 화염전파 속도를 비교 측정 한다. 측정된 화염 전파속도는 정확한 연소특성 분석을 위해 각 사이클에서의 값을 표본으로 하는 통계적 방법으로 처리한다.

• Nuclear Engineering and Technology
• /
• 제42권3호
• /
• pp.237-248
• /
• 2010

The safety of metal cask and concrete cask storage technology has been verified by CRIEPI through several research programs on demonstrative testing for the interim storage of spent fuel. The results have been reflected in the safety requirements for dry casks issued by NISA/METI (Nuclear and Industrial Safety Agency, Ministry of Economy, Trade and Industry) of the Japanese government. On top of that, spent fuel integrity has been studied by the Japan Nuclear Energy Safety Organization (JNES). This paper reviews these research programs. Future issues include the long-term integrity of cask components and high burn-up spent fuel.

• 한국자동차공학회논문집
• /
• 제3권5호
• /
• pp.56-63
• /
• 1995

In this paper, the fuel atomization effect of a spark-ignition engine on the lean burn characteristics is studied. The fuel atomization is enhanced by heating the inside of the intake manifold with electric heater. Several operating parameters including cyclic variation are expressed against the air-fuel ratio from the experimental results. The fuel atomization gives much influence on the combustion stability. As the intake manifold is heated, the combustion duration decreased and the value of COV in the lean region as well as in the theoretical equivalence ratio became smaller than of not-heated.

• Journal of Radiation Protection and Research
• /
• 제36권4호
• /
• pp.174-182
• /
• 2011

With the reactor operation conditions - 4.3 wt% $^{235}U$ initial enrichment, burn-up 55,000 MWd/MTU, average power 34 MW/MTU for three periods burned time for 539.2 days per period and cooling time for 100 hours after shut down, to set up the condition to determine the minimum height (depth) of spent fuel storage pool to shut off the radiation out of the spent fuel storage pool and to store spent fuels safely, the dose rate on the specific position directed to the surface of spent fuel storage pool induced by the neutron and gamma-ray from spent fuels are evaluated. The length of spent fuel is 381 cm, and as the result of evaluation on each position from the top of spent fuel to the surface of spent fuel storage pool, it is difficult for neutrons from spent fuels to pass through the water layer of maximum 219 cm (600 cm from the floor of spent fuel storage pool) and 419 cm (800 cm from the floor of spent fuel storage pool) for gamma-ray. Therefore, neutron and gamma-ray from spent fuels can pass through below 419 cm (800 cm from the floor) water layer directed to the surface of spent fuel storage pool.

• 한국분말재료학회지
• /
• 제6권3호
• /
• pp.209-214
• /
• 1999

The oxidation behavior of the simulated spent fuel of burn up 33 MWD/kgU was investigated to predict that of the spent fuel in the temperature ranges of 400 to $700^{\circ}C$ and was compared with those of $UO_2$. The forms of uranium oxides after the oxidation were conformed by XRD analyses. The oxidation rate at each the temperature and the activation energy were obtained. After complete oxidation, the simulated spent fuel was converted to $U_3O_8$ and pulverized to powder due to the density difference between the simulated spent fuel and uranium oxides. The activation energies were 85.35 and 30.77kJ/mol in the temperature ranges of 400$\leq$T($^{\circ}C$)$\leq$500 and 500$\leq$T($^{\circ}C$)$\leq$700, respectively.

• 동력기계공학회지
• /
• 제13권3호
• /
• pp.5-10
• /
• 2009

This work deals with a controlled auto-ignition (CAI) single cylinder gasoline engine, focusing on the extension of operating conditions. The fuel is injected indirectly into electrically heated inlet air flow. In order to keep a homogeneous air-fuel mixing, the fuel injector is cooled by the water of a specially designed coolant passage. The engine emission characteristics were investigated under the wide range of operating conditions such as 32 to 63 in the air-fuel ratio, 1000 to 1800 rpm in the engine speed, and 150 to $180^{\circ}C$ in the inlet air temperature. The ultra lean-burn can be achieved by the auto-ignition of gasoline fuel due to the heated inlet air in the compression ignition gasoline engine. It is confirmed that the emission concentrations of carbon monoxide, hydrocarbons and nitrogen oxide can be significantly reduced by CAI combustion compared with the combustion of a conventional spark ignition engine.

• 한국자동차공학회논문집
• /
• 제4권3호
• /
• pp.220-231
• /
• 1996

In this research, we use IDI type constant volume combustion chamber which may make up stratified combustion to construct the design back data of lean-burn engine. Some experiments are conducted by the passagehole angle in the adapter of main chamber and sub-chamber. The effects on the combustion characteristics according to the ignition timing are investigated. The used fuel is methanol prospective for alternative fuel. Fuel is injected under 10.78MPa using solenoid and accumulator. As the results of the experiment, combustion characteristics reveals that ignition timing, passagehole angle and shape greatly effects on. Lean inflammability limit is extended to 0.45 in equivalence ratio.