• Journal of Korean Society for Atmospheric Environment
• /
• v.31 no.4
• /
• pp.368-377
• /
• 2015

Bunker C fuel oil is a high-viscosity oil obtained from petroleum distillation as a residue. The sulfur content of bunker C fuel oil is limited to 4.0% or even lower to protect the environment. Because bunker C fuel oil is burned in a furnace or boiler for the generation of heat or used in an engine for the generation of power, carbon dioxide is emitted as a result of combustion. The objective of this study is to investigate $CO_2$ emission characteristics of bunker C fuel oil by sulfur contents. Calorific values and carbon contents of the fuels were measured using the oxygen bomb calorimeter method and the CHN elemental analysis method, respectively. Sulfur and hydrogen contents, which were used to calculate the net calorific value, were also measured and then net calorific values and $CO_2$ emission factors were determined. The results showed that hydrogen content increases and carbon content decreases by reducing sulfur contents for bunker C fuel oil with sulfur contents less than 1.0%. For sulfur contents between 1.0% and 4.0%, carbon content increases as sulfur content decreases but there is no evident variation in hydrogen content. Net calorific value increases by reducing sulfur contents. $CO_2$ emission factor, which is calculated by dividing carbon content by net calorific value, decreases as sulfur content decreases for bunker C fuel oil with sulfur contents less than 1.0% but it showed relatively constant values for sulfur contents between 1.0% and 4.0%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.94-101
• /
• 2001

In this paper, the combustion improvement effects of alcohol-diesel oil blend fuel were investigated in a visualization engine. As a result of experiment, it was found out that the combustion chamber of deep dish type and re-entrant type at the same operation condition. However, when the con-tent of alcohol exceeded 10% of total fuel delivery, the combustion of alcohol-diesel oil blend fuel was worse than that of diesel oil. The maximum blend quantity of ethanol which is not ignited in the re-entrant type combustion chamber was estimated at approximately 40% of total fuel delivery. So, it is necessary to blend appropriate quantity of a volatility fuel such as alcohol in order to improve combustion.

• Journal of ILASS-Korea
• /
• v.2 no.3
• /
• pp.8-16
• /
• 1997

Ta investigate characteristics and spray of emulsified fuet we are mixed water with diesel oil using ultrasonic energy fuel feeding system. Separation ratio of emulsified fuel was shown good condition that of water content is small and longer ultrasonic energy adding time. Viscosity of emulsified fuel increased 79% with addition to water content and surface tension increased 1.6% in comparision to pure diesel oil. The SMD of emulsified fuel adding ultrasonic energy decreased with 3% in comparision to pure diesel oil. With increasing 5, 10% water content the SMD decreased 15.6, 20.1% in comparision to pure diesel oil. The mind-explosion was investigated with 4step.

• Journal of Biosystems Engineering
• /
• v.37 no.5
• /
• pp.296-301
• /
• 2012

Purpose: Combustion and fuel qualities of the animal-fats biodiesel as a heating fuel for agricultural hot air heater were studied. Methods: Biodiesel (BD) was made from animal-fats by reacting with methanol and potassium hydroxide in the laboratory. The biodiesel made in the laboratory was tested for fuel and combustion qualities. Results: The kinematic viscosity and the calorific values of the biodiesels were measured. Kerosene based biodiesel, BD20 (K) showed 18 cSt at $-20^{\circ}C$. It seemed that BD100 was not suitable for a heating fuel under some temperature. As BD content increased, the calorific value decreased up to 40,000 J/g for BD100, while the calorific value of light oil was 45,567 J/g showing difference of 5,567 J/g, about 12% difference. Several different fuels including BD20 (biodiesel 20% + light oil 80%), BD50 (biodiesel 50% + light oil 50%), BD100 (biodiesel 100%), and light oil were tested for fuel combustion qualities for agricultural hot air heater, and their combustion performances were compared and analyzed. Flame dimensions of biodiesels and light oils were almost the same shape at the same combustion condition. Generally, the $CO_2$ amounts of BDs were greater than light oil. However, in this study the differences were minor, so there was no significant difference existed between the BDs combustion and light oil. Conclusions: It seemed that quality was good for heating oil for agricultural hot air heater because of showing no barriers for continuous combustion and proper exhaust gas temperature and $CO_2$ amount discharged. But, for fuel fluidity for higher BD content fuel could be a detrimental problem in situations where the outdoor temperature is lowered. As BD content increased, calorific value decreased up to 40,000 J/g for BD100. Calorific value difference between BD20 and light oil was about 1,360 J/g.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.4
• /
• pp.362-368
• /
• 2016

In the recent International Maritime Organization's (IMOs) Maritime Safety Committee's 93rd session, the International Chamber of Shipping and International Parcel Tankers Association addressed marine fuel oil quality problems: increasing diluents in marine fuel oil, ignition in engine rooms due to the low flash point of fuel oil, and marine fuel oils that can damage marine engines. To deal with these marine fuel oil quality problems, the International Maritime Organization secretariat appointed the worlds marine fuel oil monitoring institute and constituted a correspondence group to determine the fuel oil quality required by MARPOL Annex VI regulation 14.8 (sulfur content less than 0.5%). In this study, basic research that can help with responding to marine fuel quality issues and the IMO's work is conducted. In order to perform this basic research, the off-spec ratio related to the fuel oil quality standard (ISO 8217:2012), density distribution tendency, gross specific energy, and correlation between components in the fuel oil are analyzed through actual marine fuel oil (residual marine fuel) data from the Port of Singapore.

• Proceedings of the Korean Professional Engineer Association Conference
• /
• 1984.12a
• /
• pp.84-91
• /
• 1984

Heavy Residual Fuel oils is a mixture of reduced crude from crude unit, bottom products from vacuum and/or catalytic cracking unit with distillate to meet the specification and generally used as Heavy Fuel Oil for large combustion engines, boilers, etc…. But this study was made to investigate Heavy Residual Fuel oils for using as industrial raw material and resulted the following possibilties as valuable raw material as well as Heavy Fuel Oil. 1) Production of straight asphalt through vacuum distillation unit. 2) Using straight asphalt from vacuum distillation unit for manufacturing of Blown Asphalts, Cut Back Asphalts, Emulsified Asphalts and Asphalt Compound, etc…. 3) Using waxy oil side streams for manufacturing of raw oil to be Lube Oil base stocks through solvent dewaxing. 4) Production of lube base oils from dewaxed raw oil through chemical treatments. 5) Manufacturing of paraffine wax from slack wax to be produced as by product of dewaxing process.

• Journal of Korea Ship Safrty Technology Authority
• /
• s.27
• /
• pp.2-14
• /
• 2009

In these days, oil cost is about 70 US dollars, but, on the day of July. 2008, it was over 140 US dollars. This coast led fisheries industry to increasement of operating coast and made public problems such as non-operation of fishing boats and lockout of the related factories. Thus this paper studies the way to use cheap fuel in order to reduce the fuel cost. Normally fishing boat use Marine Gas Oil. this study explains to use blended oil such as MF 60, 100, 180 instead of MGO.

• Tribology and Lubricants
• /
• v.26 no.5
• /
• pp.291-296
• /
• 2010

The purpose of this paper is to study the fuel economy improvement experimentally when the viscosity of engine oil is lowered. The emissions are measured for CVS-75 mode with SAE viscosity grades. The test results indicate that a close correlation has been found between the engine oil viscosity and the fuel economy. The lowering of engine oil viscosity causes the reduction of friction loss which has a very close relation with the fuel economy. These results as the lowering of engine oil viscosity will be a important factor for improvement of the fuel economy and reduction of the $CO_2$ emission.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.562-571
• /
• 2014

In these days, many countries carry out many renewable energy policies to increase the renewable energy portion and to reduce the GHG(Green House Gas). In Korea, RPS(Renewable Portfolio Standards) focused on over 500MW power producers is conducting. And they are using the bio-fuel oil to meet their RPS quota. The oil is a mixture of animal and vegetable fat or fatty acid ester of them and should satisfy some specifications to use the power generation such as viscosity, pour point, acid number. Depends on the raw materials, quality characteristics of power bio-fuel oil are changed. By adding the power bio-fuel oil, pour point, density, sulfur content and viscosity are decreased and acid number, iodine number, oxygen content are increased. In this study, we test the quality characteristic of power bio-fuel oil and the property changes by the blending ratio of power bio-fuel oil & conventional fuel oil.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.1
• /
• pp.41-47
• /
• 2012

Recently, due to the rapid rise of the international oil price, the burden of fuel oil expense is relatively increasing in a ship. And the international restriction of the greenhouse gas which was generated from the burning of fuel oil is also rapidly strengthened. Therefore, to reduce the greenhouse gas and fuel oil consumption, many shipping company adopted the low speed navigation and it was focused on the improvement of fuel consumption efficiency and the usage of alternative energy in the marine engine development field. In this paper, the fuel oil consumption according to the ship's speed was measured in the actual seas and analyzed the shop test results in the shipyard and the ship navigation data from the abstract log. And then it was proposed that the ship's economic speed was 14~15kts and the optimum rpm was 140~150 in specific sea conditions.