• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제37회 추계학술대회논문집
• /
• pp.554-557
• /
• 2011

금속분말을 연료로 하는 연소기 개발에 있어 발생하는 문제점 중에 하나는 알루미나 slag 처리이다. 연소기 내부에 Water film을 형성시킴으로써 금속분말 연소기의 문제점을 해결할 수 있을 것으로 기대한다. 이를 위한 선행연구로 water film의 형성 조건에 대한 실험을 수행하였다. 실험 모델에 대하여 물 분사 속도가 증가할수록 원형 모델에 대한 water fim 각도가 작아져, 약 10 m/s이상에서 완전한 water film이 형성되는 것을 알 수 있었다.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.114-122
• /
• 1997

Nowadays, gasoline direct injection engines are being commercialized by virtue of improvement in control technology of spray, flow, air fuel ratio. The stratified charge type has the advantage of improving lean limit. The homogeneous type has the advantage of reducing engine-out hydrocabon emissions in the first 30 seconds after a cold start, in addition, improving transient air fuel ratio control. The vaporization and mixing if injected fuel with air has to e completed in a short time and the fuel film in cylinder and on piston has to be minimized. So, the flow and injection should be well controlled. This paper surveyed the spray characteristics of gasoline direct injection by using laser equipment and the combustion characteristics of the single cylinder engine using homogeneousas-mixture type gasoline direct injection.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.546-549
• /
• 2008

Hyundai Motor Company has made an effort to develop fuel cell electric vehicle and its subsystem in recent years. This paper deal with the development of electric drive system applied to Hyundai's fuel cell electric vehicle. This system is composed of three main components such as motor, inverter and DC/DC converter. The specifications of each system is introduced briefly and experimental result of its main components is presented. In addition, we introduce the development status of power semiconductor device, film capacitor, inductor and permanent magnet.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(3)
• /
• pp.265-270
• /
• 1996

The temperature distribution in the pellet was obtained from beginning the general heat conduction equation. The thermal conductivity of pellet used the SIMFUEL data that made clear the effect of burnup on the thermal conductivity degradation. Since the pellet rim acts as the thermal barrier to heat flow. the pellet was subdivided into several rings in which the outer ring was adjusted to play almost the same role as the rim. The local burup in each ring except the outer ring was calculated from the power depression factor based on FASER results. whereas the rim burnup at the outer ring was achieved by the pellet averaged burnup based on the empirical relation. The rim changed to the equivalent Xe film so the predicted temperature shooed the thermal jump across the rim. The observed temperature profiles depended on linear heat generation rate. fuel burnup. and power depression factor. The thermal conductivity degradation modelling can be applied to the fuel performance code to high burnup fuel,

• 한국자동차공학회논문집
• /
• 제9권6호
• /
• pp.57-64
• /
• 2001

This study presents an self tuning regulator(STR) to improve the air-fuel ratio control of performance of gasoline engine. The STR is designed based on the nonlinear dynamic engine model, and the performance of the STR is evaluated through the simulation and experiments. The STR shows better performance than a conventional PI controller in terms of the response time and disturbance rejection. Since the STR has less calculation load than the complex nonlinear controller, this algorithm can be easily applied to on-board engine controller.

• 한국세라믹학회지
• /
• 제36권4호
• /
• pp.391-402
• /
• 1999

Characteristics of composite electrolytes which were prepared by coating a thin film of YSZ (yttria sta-bilized zirconia : (ZrO2)0.92 (Y2O3)0.08) on YDC (yttria doped ceria : Ce0.8Y0.2O1.9) with mixed conductivity have been investigated in order to develop the low-temperature solid oxide fuel cell. The thickness (t) of spin-coated YSZ thin films after the heat-treatment at 600$^{\circ}C$ was increased proportionally to the sol con-centrations (C) while the decrease in its thickness with the spin rate ($\omega$) could be expressed in the e-quation of ln t=9.49-0.53 ln $\omega$(0.99mol//s sol conc.) When the sol concentration and the spin rate being less than 0.99 mol/l and higher than 1000 rpm respectively reliable YSZ/YDC composite electrolytes could be obtained by multi-coating although several micro-cracks were observed in singly coated YSZ film surfaces. The dense YSZ film with a 1$\mu\textrm{m}$ thickness was prepared by coating of 0.99 mol/l YSZ sol five-times at 2000 rpm followed by heat-treatment at 1400$^{\circ}C$ for 2h, The adhesion between YSZ film and YDC substrate was found to be very good. The open circuit voltages of H2/O2 single cell with YSZ/YDC composite electrolytes were 0.79∼0.82 V at 800$^{\circ}C$ and 0.75∼0.77V at 900$^{\circ}C$ The open circuit voltage was inversely proportioned to the thickness ratio of YSZ thin film (1$\mu\textrm{m}$) to YDC substrate(0.28-2.22 mm)

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제10권6호
• /
• pp.63-67
• /
• 2005

불포화 토양내에서 가스상 오존의 이동특성에 대한 토양수분과 Light non-aqueous phase liquid (LNAPL)의 영향을 알아보기 토양칼럼실험을 실시하였다 토양수분은 토양입자에 수막을 형성하여 가스상 오존과 토양입자의 직접적인 접촉을 방해하여 오존의 이동을 증가시키는 역할을 하였다. 토양수분이 증가할수록 불포화 토양내의 기-액 접촉면적 감소와 오존의 평균선형유속증가로 인해 오존의 이동속도가 증가하였다. LNAPL로 사용된 디젤유의 경우도 토양 표면에 막(Film)을 형성하여 가스상 오존의 이동을 증가시키는 역할을 하였다. 하지만, 토양 수분과는 반대로 디젤유 농도가 증가할수록 오존의 이동속도는 감소하였다. 토양수분과 LNAPL성분이 동시에 존재할 경우에는 토양입자에 Non-wetting유체로 작용하는 LNAPL에 의해 오존의 이동이 영향을 받는다는 것을 알 수 있었다

• Journal of Microbiology and Biotechnology
• /
• 제19권9호
• /
• pp.1019-1027
• /
• 2009

A noncompartmented microbial fuel cell (NCMFC) composed of a Mn(IV)-carbon plate and a Fe(III)-carbon plate was used for electricity generation from organic wastewater without consumption of external energy. The Fe(III)-carbon plate, coated with a porous ceramic membrane and a semipermeable cellulose acetate film, was used as a cathode, which substituted for the catholyte and cathode. The Mn(IV)-carbon plate was used as an anode without a membrane or film coating. A solar cell connected to the NCMFC activated electricity generation and bacterial consumption of organic matter contained in the wastewater. More than 99% of the organic matter was biochemically oxidized during wastewater flow through the four NCMFC units. A predominant bacterium isolated from the anode surface in both the conventional and the solar cell-linked NCMFC was found to be more than 99% similar to a Mn(II)-oxidizing bacterium and Burkeholderia sp., based on 16S rDNA sequence analysis. The isolate reacted electrochemically with the Mn(IV)-modified anode and produced electricity in the NCMFC. After 90 days of incubation, a bacterial species that was enriched on the Mn(IV)-modified anode surface in all of the NCMFC units was found to be very similar to the initially isolated predominant species by comparing 16S rDNA sequences.

• 한국세라믹학회지
• /
• 제48권6호
• /
• pp.487-492
• /
• 2011

The effect of the application of lanthanum strontrium manganite and yttria-stabilized zirconia (LSM-YSZ) nano-composite fabricated by pulsed laser deposition (PLD) as a cathode of solid oxide fuel cell (SOFC) is studied. A gradient-structure thin-film cathode composed of 1 micron-thick LSM-YSZ deposited at an ambient pressure ($P_{amb}$) of 200 mTorr; 2 micron-thick LSM-YSZ deposited at a $P_{amb}$ of 300 mTorr; and 2 micron-thick lanthanum strontium cobaltite (LSC) current collecting layer was fabricated on an anode-supported SOFC with an ~8 micron-thick YSZ electrolyte. In comparison with a 1 micron-thick nano-structure single-phase LSM cathode fabricated by PLD, it was obviously effective to increase triple phase boundaries (TPB) over the whole thickness of the cathode layer by employing the composite and increasing the physical thickness of the cathode. Both polarization and ohmic resistances of the cell were significantly reduced and the power output of the cell was improved by a factor of 1.6.

• 전기화학회지
• /
• 제5권2호
• /
• pp.62-67
• /
• 2002

용융탄산염 연료전지의 성능 저하와 수명 감소의 원인이 되는 부식 현상을 규명하고자 분리판 재료로 가장 널리 사용되고 있는 AISI-type 316L stainless steel을 대상으로 62Li/38K계 용융탄산염 내에서의 부식 실험을 수행하였다. 부식의 형태 및 속도는 환경에 의하여 다양하게 변화하게 되며, 용융탄산염 내에서 AISI-type 316L stainless steel의 부식 속도는 부식 반응에 의하여 형성되는 부동태 산화막의 안정성에 의하여 크게 영향을 받는다. 전기화학적 분극 거동을 분석한 결과 용융탄산염 연료전지의 anode가슨 분위기에서는 안정한 부동태 산화막이 형성되지 않았다. 순환 전압전류법과 정전위법을 이용한 부식 생성물의 X-ray분석을 통하여 특정한 전기화학적 전위 영역에서 반응기구와의 인과관계를 규명하고 다양한 형태의 부식 반응들을 분리해 내었다.