• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2005년도 학술발표회(2)
• /
• pp.951-951
• /
• 2005

The characteristics of Boussinesq starting forced plumes were investigated in this study. Two distinct periods in the transient plume penetration were identified, namely the Period of Flow Development (PFD) and Period of Developed Flow (PDF). PFD refers to the time period whereby the penetration rate is governed by the complex vortex dynamics initiated by the exit conditions that can include vortex coalescence, vortex leapfrogging, pinching off of the head vortex from the trailing stem and the eventual reconnection. The pinch-off and reconnection leads to an overshoot of the plume front which is a common observation reported in previous studies. The penetration rate in PDF is more predictable and depends on the continuous feeding of buoyancy and momentum into the head vortex by the trailing buoyant-jet stem. Similarity solutions are developed for PDF to describe the temporal variation of the penetration rate, by incorporating the behavior of an isolated buoyant vortex ring and recent laboratory results on the trailing buoyant jet. In particular, the variations of velocity ratios between the head vortex and trailing buoyant jet are analytically computed. To verify the similarity solutions, experiments were conducted on vertical starting forced plumes using planar laser induced fluorescence (PLIF).

• 대한화학회지
• /
• 제3권1호
• /
• pp.23-27
• /
• 1954

The relation between the height of ascending solvents and its velocity were studied with strips of Toyo No. 50 filter paper. The filter paper strip of 3cm width and cat 30 cm length is hooked down or fixed between two sheets of glass plates inside a cylinder containing the solvent, in which the lower end of the strip is dipped. As the solvents, acetone, hydrochloric acid, water or mixtures of these are used. For short time intervals, Ostwald's folmula $h = Kt^n$ was found to be most suitable to express the relation between the height of the solvent front, h, and time, t. For longer time intervals, results will be discussed in the next paper. The mean values of the constant m in the above formula for pure acetone and pure water were 0.44 and 0.485, respectively, and that of K were 0.05 and 2.4, respectively. The time interval whose the above formula applies, for each solvent was 2 hours for the former, and a half hour for the later, respectively. The movement of solutes, such as $Cu^{++}$ and $Fe^{++}$ showed that the Rf values of solutes become constant values after a long periods; e.g., ca. 6 hours with 10N-HCl-Acetone (1 : 9) solvent.

• 한국해양공학회지
• /
• 제27권1호
• /
• pp.93-101
• /
• 2013

The incident bore impact loads acting on a tall structure is simulated using the refined Moving Particle Simulation (MPS) method. The particle method is more feasible and effective than conventional grid-based methods for the violent free-surface problems. In the present study, the simulation results for the temporal change of the hydrodynamic force on the structure and longitudinal velocity component around the structure are compared with the experiments (Radd and Bidoae, 2005). And the mitigation effects by installation of various obstacles in front of the main structure are investigated and discussed form the simulation results.

• International Journal of Fluid Machinery and Systems
• /
• 제2권3호
• /
• pp.189-196
• /
• 2009

The effect of inlet and outlet blade angles on a micro regenerative pump head was examined in experiments. The pump head was little increased by changing the blade angles compared with the original pump with the inlet and outlet blade angles of 0 degree. The effect of the axial clearance between the impeller and the casing on the pump head was also examined. The head was increased largely by decreasing the axial clearance. The computation of the internal flow was performed to clarify the cause of the increase of the pump head due to the decrease of the clearance. The local flow rate in the casing decreased as the leakage flow rate through the axial clearance decreased due to the decrease of the clearance. It was found that the larger head in the smaller clearance was just caused by the smaller local flow rate in the casing. In the case of the smaller clearance, the smaller local flow rate caused the smaller circumferential velocity near the front and rear sides of the impeller. This caused the increase of the angular momentum in the casing and the head.

• 한국해양공학회지
• /
• 제16권6호
• /
• pp.7-17
• /
• 2002

Recently, artificial rocks, instead of buoys, have been placed on the submerged breakwater to indicate its location. The accurate estimation of wave forces on these rocks is deemed necessary for their stability design. Characteristics of the wave force, however, are expected . to be very complicated because of the occurrence of breaking or post-breaking waves. In this regard, wave forces exerted on an artificial rock have been investigated in this paper. The maximum wave force has been found to strongly dependent on the location and shape of the artificial rock that is placed on the submerged breakwater. The plunging breaker occurs near the loading cram edge of a submerged breakwater, which cause impulsive breaking wave force on the rock. Using the Morison equation, with the velocity and acceleration at the front face of the artificial rock and varying water surface level, it is possible to estimate wave forces, even impulsive breaking wave forces, that are acting on the rock installed on a submerged breakwater. The vertical wave force is also found to depend, significantly, on the buoyant force.

• 전자공학회논문지SC
• /
• 제49권3호
• /
• pp.12-18
• /
• 2012

본 논문에서는 항공기에 장착된 안테나가 정지 위성을 향하도록 관성측정기를 사용하여 지향각을 계산하는 방식을 제시한다. 대상 시스템에서 안테나는 항공기 앞에 위치하고 있고 몸체 유연성을 고려하기 위해 관성측정기를 도입하며, 항공기 중심부 GPS/INS와 안테나부 관성항법장치(INS) 사이의 위치와 속도 차이를 활용하여 스트랩다운 INS 표류 오차를 억제하기 위한 칼만필터를 설계한다.

• Journal of Mechanical Science and Technology
• /
• 제15권7호
• /
• pp.895-905
• /
• 2001

This paper presents vector fields, three dimensional mean velocities, turbulent intensities, turbulent kinetic energy and Reynolds shear stresses measured in the X-Y plane of the gas swirl burner with a cone type baffle plate by using an X-type hot-wire probe. This experiment is carried out at the flow rates of 350 and 450ℓ/min which are equivalent to the combustion air flow rate necessary to release 15,000 kcal/hr in a gas furnace. The results show that the maximum axial mean velocity component exists around the narrow slits situated radially on the edge of a burner. Therefore, there is some entrainment of ambient air in the outer region of a burner. The maximum values of turbulent intensities occur around the narrow slits and in front of a burner up to X/R=1.5. Moreover, the turbulent intensity components show a relatively large value in the inner region due to the flow diffusion and mixing processes between the inclined baffle plate and the swirl vane. Consequently, the combustion reaction is expected to occur actively near these regions.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1572-1577
• /
• 2003

High-power pulsed laser ablation under atmospheric pressure is studied utilizing numerical and experimental methods with emphasis on recondensation ratio, and the dynamics of the laser induced vapor flow. In the numerical calculation, the temperature pressure, density and vaporization flux on a solid substrate are first obtained by a heat-transfer computation code based on the enthalpy method, and then the plume dynamics is calculated by using a commercial CFD package. To confirm the computation results, the probe beam deflection technique was utilized for measuring the propagation of a laser induced shock wave. Discontinuities of properties and velocity over the Knudsen layer were investigated. Related with the analysis of the jump condition, the effect of the recondesation ratio on the plume dynamics was examined by comparing the pressure, density, and mass fraction of ablated aluminum vapor. To consider the effect of mass transfer between the ablation plume and air, unlike the most previous investigations, the equation of species conservation is simultaneously solved with the Euler equations. Therefore the numerical model computes not only the propagation of the shock front but also the distribution of the aluminum vapor. To our knowledge, this is the first work that employed a commercial CFD code in the calculation of pulsed ablation phenomena.

• 대한기계학회논문집B
• /
• 제30권4호
• /
• pp.306-313
• /
• 2006

Automated material handling system is being used as a method to reduce manufacturing cost in the semiconductor and flat panel displays (FPDs) manufacturing process. Those are considering switch-over from the traditional cassette system to single-substrate transfer system to reduce raw materials of stocks in the processing line. In the present study, the wafer transportation speed has been evaluated by numerical and experimental method for three propulsion nozzle array (face, front, rear) in an air levitation system. Test facility for 300 mm wafer was equipped with two control tracks and a transfer track of 1,500mm length. The diameter of propulsion nozzle is 0.8mm and air velocity of wafer propulsion is $50\sim150m/s$. We found that the experimental results of the wafer transportation speed were well agreed with the numerical ones. Namely, the predicted values of the maximum wafer transportation speed are higher than those values of experimental data by 16% and the numerical result of the mean wafer transportation speed is higher than the experimental result within 20%.

• 대한기계학회논문집A
• /
• 제24권12호
• /
• pp.2883-2890
• /
• 2000

In this study, a Hardware-In-The-Loop-Simulation(HILS) system for developing a Electric-Power-Steering(EPS) system is designed. To test a EPS by HILS system, a mathematical vehicle model with a steering system model has been constructed. This mathematical model has been constructed. This mathematical model has been downloaded to the Digital-Signal-Processor(DSP) board. To realize the lateral force acting on the front wheel in a real car. the steering wheel angle sensor and vehicle velocity have been used for input signal. The force sensor has been used for a feedback signal. The full vehicle states could by simulated by the HILS system. Consequently, the HILS system could by used to analyze control-parameters of a EPS that contributes to the maneuverability and stability of a vehicle. At the same time, the HILS system can evaluate the whole performance of the vehicle-steering system. Also the HILS system could do test could not be executed in real vehicle. The HILs system will useful for developing the control logic for the EPS system.