• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.04a
• /
• pp.59-60
• /
• 2012

• KSTLE International Journal
• /
• v.1 no.1
• /
• pp.1-7
• /
• 2000

Eviction characteristics of two typical friction materials (non-asbestos organic and low-steel friction materials) for an automotive brake system were investigated using an inertial brake dynamometer. In particular, the effect of sliding speed on friction coefficient was carefully investigated employing various test modes. The two friction materials were developed for commercial applications and were different mainly in the type and the amount of metallic ingredients in the friction material. The dynamometer test showed that the low-steel friction material was sensitive to the sliding speed exhibiting a negative $\mu$-v relation. On the other hand, the non-asbestos organic friction material was less sensitive to the sliding speed. The low steel friction materials with a negative $\mu$-v relation also induced larger vibration amplitude during brake applications.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.1
• /
• pp.28-34
• /
• 2014

This study provides the numerical finite-element method(FEM) estimating the friction noise induced by the negative slope in the friction-velocity curve. The friction noise due to the friction-velocity curve is experimentally investigated through the pin-on-disk setup. The measured squeal frequency is estimated by FEM. The friction curve is measured by the friction test, then it is applied to the complex eigenvalue analysis. The results shows that the experimental squeal frequency can be determined by the FEM analysis. Also, it is emphasized that the negative friction-velocity slope is essential in generating friction noise in the pin-on-disc system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.8
• /
• pp.748-755
• /
• 2012

Friction causes self-excited vibration, stick-slip vibration and any other friction-induced phenomena. That kinds of vibrations cause chatter and squeal. In order to predict such vibrations accurately, employing an accurate friction model is very important because a dynamic behavior of a system with friction is dominantly governed by a friction model. A Coulomb friction model is the most widely known model. Coulomb friction model is useful model to obtain analytical solutions of the system with friction and the model gives relatively good simulation result. However, defining a friction force at a stick state in simulation is hard because of the characteristic itself and a Coulomb friction model is discontinuous function between a static and a dynamic friction coefficient. Therefore, applying the Coulomb friction model to a simulation is not appropriate. In order to resolve these problems, an approximated Coulomb friction model was developed using simple and continuous function. However, an approximated Coulomb friction model cannot realize stick. Therefore, an approximated Coulomb friction model cannot describe friction phenomena accurately. In order to analyze a friction phenomenon accurately, a friction model for a simulation was proposed in this paper. A proposed friction model realizes stick and gives reasonably good results compared to results obtained by the simulation employing an approximated Coulomb friction model. Accuracy of a proposed friction model was verified by comparing experimental results.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.383-384
• /
• 2002

Frictional sound is observed in great many practical systems, but its generation mechanism is still unknown Model systems are best suited for research on the fundamental mechanisms, but results cannot be easily applied to real systems, because each system has different sound radiation properties. At present, there is no easy method for evaluation of these properties. We propose to describe the sound radiation property of a tribo-system by the relationship between friction-induced sound power and the friction-induced vibration velocity of the contact element. It was found that the sound power of a tribo-system is linearly proportional to the mean-square velocity of the sliding element by a constant coefficient having the dimension of mass flow rate (kg/s).

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.603-606
• /
• 2007

Wind induced vibration of a stay cable with a nonlinear friction damper is investigated. Stay cables are likely to vibrate under several wind-related environments, and cable dampers can be used to suppress the excessive vibrations of stay cables. Conventional design of cable dampers are based on the equivalent modal damping achieved by the cable damper. However, the equivalent modal damping achieved by nonlinear dampers are depend on the vibration characteristics like the amplitude of the vibration. In this paper, not only the achieved equivalent modal damping, but also the vibration levels under gust wind are analyzed through the time domain buffeting analysis. Numerical simulation results show the efficacy of a nonlinear friction damper for suppressing the excessive vibration of a stay cable.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.12
• /
• pp.1206-1212
• /
• 2012

The brake squeal propensity due to the friction-velocity curve is numerically investigated. The finite element models for the disc and pad are correlated with the modal test. In the friction-engaged system modeling, the friction function is linearized at the equilibrium. The damping term induced by friction-velocity slope is incorporated into the equations of motion. In the complex eigenvalue analysis, it is found that the pad shear mode is very sensitive to the friction curve. The results shows that the squeal propensity of the pad shear mode can be controlled by the design parameters such as pressure and stiffness.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.06a
• /
• pp.166-172
• /
• 2000

Friction characteristics of phenolic resin-based friction composites containing threedifferent relative amounts of graphite and zirconium silicate were investigated by using a pad-on-disk type friction tester. Constant temperature test and constant interval test at three different initial temperatures(100. 200, 300$^{\circ}C$) were performed to examine the effects of friction heat on friction characteristics at elevated temperature. The friction composite(FMO.7) with higher content of ZrSiO$_4$showed unstable friction force at higher temperature and resulted in larger fluctuations of vibration during friction test. The abrasive action of ZrSiO$_4$in friction composite impeded stable transfer film and induced higher friction heat at friction interface. Friction oscillations according to the temperature were associated with the formation of transfer film(i'd body layer) on the friction composite and the counter part.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11a
• /
• pp.331.1-331
• /
• 2002

Four degrees of freedom mathematical model is presented to describe the fundamental mechanisms of the disc brake squeal noise. A contact parameter is introduced to describe the coupling between the in-plane and the out-of-plane motions. The friction coeficient including "relative velocity" and ′normal force" can be generally formulated as the form of multiplication with polynominal parameters(${\beta}$, ${\gamma}$). (omitted)

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.8
• /
• pp.736-741
• /
• 2012

Squeak noise is studied by using the pin-on-disk system with aluminum pin and steel disk. Noise induced by friction is measured with respect to the normal loads and sliding speeds. The negative slope of friction-velocity curve is seen when the squeak noise occurs. It is found that the normal load influences on the sound level of squeak noise. From the hammering test, the major frequency of the squeak noise is shown to correspond to one of system modes, which implies that squeak phenomenon arises from the unstable system modes. The result of FE analysis shows that the major squeak mode is the bending mode of the pin.