• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.2
• /
• pp.153-162
• /
• 1997

In this study, the wet surface heat transfer coefficients and friction factors of the heat exchanger with slit-wavy fin were measured. Four sample cores of two or three row with fins of 12 fpi or 16 fpi were tested. Tests were conducted in a closed loop wind tunnel, where the heat exchanger was mounted at 45 degree inclination angle. The wet surface heat transfer coefficient was reduced following the procedure given in ARI 420-81. During the course, new definitions of the $\varepsilon$-NTU applicable to enthalpy driving system were introduced. The wet surface heat transfer coefficients were approximately equal to the dry surface values. However, the friction factors were approximately 120% to 170% higher than those of the dry surface. Both the heat transfer coefficient and the friction factor of the wet surface increased as the relative humidity increased, fin pitch decreased, and the number of row decreased, although the difference was not large.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.133-137
• /
• 2003

The shock absorber for vehicles is the important component to absorb the shock in driving. These essential components, piton and piston rod, must be made of S25C, S45C and SCM440 generally depending on kind of vehicles, precisely machined and assembled by the bolt. And it has been difficult to weld this sort of dissimilar materials. They could be unstable in the quality by the conventional arc welding. And also they have a lot of technical problems in manufacturing. But by the friction welding technique, it will be able to be made without such problems. These factors above necessitate nowadays the domestic development of the shock absorber by friction welding and a new approach of study on real-time quality evaluation by AE techniques.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.5 s.98
• /
• pp.151-159
• /
• 1999

A self-propulsive polishing robot is proposed as a method which automates a floor polisher. The proposed robot with two rotary brushes does not require any mechanism such as wheels to obtain driving forces. When the robot polishes a floor with its two brushes rotating, friction forces occur between the two brushes and the floor. These friction forces are used to move the robot. Thus, the robot can move in any direction by controlling the two rotary brushes properly. In this paper, firstly a dynamics model of a brush is presented. It computes the friction force between the brush and the floor. Secondly, the dynamics of the proposed robot is presented by using the bush dynamics. Finally, the inverse dynamics is solved for the basic motions, such as the forward, backward, leftward, rightward motions and the pure rotaion. This paper will contribute to realize a self-propulsive polishing robot as proposed above, In addition, this paper will give basic ideas to automate the concrete floor finishing trowel, because its basic idea for motion is similar to that of the proposed robot.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.1 s.62
• /
• pp.44-48
• /
• 2005

The shock absorbers for marine vehicles are very important components to absorbing the shock resulting from driving. Depending on the kinds of vehicles, these essential components, piston and piston rod, must be made of S25C, S45C, and SCM440, must be precisely machined, and assembled by the bolts. Other materials used have been difficult to weld, and could be unstable in quality, by the conventional arc welding. Also, they have been associated with a lot of technical problems in manufacturing. However, using the friction welding technique, such problems will be avoided. These factors have necessitated the domestic development of the marine shock absorber using a friction welding, as well as stimulating a new approach to the study of real-time weld quality evaluation by AE techniques.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.6
• /
• pp.309-314
• /
• 2021

Due to the superior corrosion resistance and mechanical properties of TiAl alloy at high temperature, it has been utilized as a turbine wheel of a turbocharger. The dissimilar metallic bonding is usually applied to combine the TiAl turbine wheel with the SCM440 structural steel which is used as a driving shaft. In this study, the TiAl and SCM440 joint were fabricated by using a friction welding technique. During bonding process, to suppress the martensitic transformation and the formation of cracks, which might reduce a strength of the joints, Cu was used as an insert metal to relieve stress. As a result, the intermetallic compounds (IMCs) layer was observed at TiAl/Cu interface while no IMC formation was formed at SCM440/Cu interface. Since understanding of the IMCs effects on the mechanical performance of welded joint is also essential for ensuring the reliability and integrity of the turbocharger system, we estimated the nanohardness of welded joint region through nanoindentation. The relation between the microstructural feature and its mechanical property is discussed in detail.

• Journal of the Korean Geotechnical Society
• /
• v.40 no.3
• /
• pp.19-31
• /
• 2024

In Korea, driven piles are generally penetrated up to weathered rock or harder strata. Friction piles have been used to some extent in the southwest coastal area with deep soils; however, friction piles are not extensively due to uncertainties about construction quality. The embedded pile construction method is primarily used due to noise and vibration complaints. However, in Southeast Asian countries (e.g., Cambodia, Myanmar, and Vietnam), where soft sediments are deep, the driven pile method is commonly used due to its economic advantages. Construction companies are increasingly entering overseas construction markets, e.g., Southeast Asia; thus, it is necessary to understand the behavior of driven friction piles in the soil and improve on-site engineering management to gain market competitiveness in these countries. In this study, the bearing capacity of friction piles driven into clayey coastal soils in Vietnam with time-dependent characteristics was evaluated based on the dynamic and static pile load tests. Based on the results, a modified Danish formula is proposed for on-site quality management.

• Journal of Korean Society of Transportation
• /
• v.22 no.7 s.78
• /
• pp.25-32
• /
• 2004

It is implicated in the current road design manual that design speed is well representing the operating speed of drivers. On the contrary, the disparity between the design speed and operating speed means that current road design cannot guarantee the safety and comfort of driving. In this context, operating speed was observed at the two lane rural roadways to find out the relation of operating speed and design speed. In addition to this, the friction factor from supply and demand which was derived from the operating speed was compared in terms of the dynamics in driving safety factor. It was concluded that the actual speed was consistently exceeding the design speed at the horizontal curves having the radius less than or equal to 200 m. Similarly, the demanded side friction was also consistently exceeding the supplied side friction at the horizontal curves having the radius less than or equal to 200 m and the amount of difference was also inversely proportional to the radius of the horizontal curves.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1347-1353
• /
• 2011

Friction stir welding (FSW) method has extensively been used in manufacturing methods because of the several advantages over conventional welding methods, such as better mechanical properties, reduced occurrence of joining defects, high material saving, and low production time, etc. The aim of this paper is to review the optimal FSW conditions using the previous experimental results and is to investigate the fatigue crack growth rate in three different zones, WM, HAZ and BM for FSWed Al7075-T651 aluminum plates. As far as our experiments are concerned, the optimal conditions are obtained as rotation speed, 800rpm and travelling speed, 0.5mm/sec. The fatigue crack growth rate showed strong dependency on three different zones WM, HAZ and BM, and crack driving force.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.3
• /
• pp.40-46
• /
• 2021

An automatic transmission of automobiles enables comfortable driving experience with lower transmission shifting jerks. However, the assembly structure is more complicated and requires additional components with lower efficiency than the manual transmission system. Extensive research has been conducted to improve the overall transmission efficiency by optimizing each component of the automatic transmission assembly. This study focuses on enhancing the friction torque of double angular contact ball bearings used in automatic transmission. The friction torque of the bearing varies with the operating conditions such as the operational load and rotating speed. Since reducing the friction torque of the bearing tends to deteriorate the durability of the bearing, it is necessary to design the bearing having a minimum required friction torque by determining the durability life of an automatic transmission assembly, In this study, the theoretical life and friction torque of conventional and newly-developed bearings are calculated. The difference in the friction torque between the new and existing bearings are also evaluated.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.1
• /
• pp.5-14
• /
• 2023

The pile driving process may lead to ground heaving, causing additional positive skin friction to act on the piles, compromising their stability. This study proposes a new pile foundation type that can reduce positive skin friction. This was investigated by designing and constructing a pile with a hydraulic cylinder which actively responds to ground deformation. The newly proposed pile design was compared against traditional piles in multiple model tests where ground heaving was simulated. In the tests, base load and total shaft resistance were measured during ground heaving and with expansion of the hydraulic cylinder. As a result of the tests, a very small amount of expansion of the hydraulic cylinder member completely reduced the positive skin friction and increased the base load. Excessive expansion of the hydraulic cylinder, however, generates negative skin friction beyond the zero skin friction state. Therefore, it is necessary to estimate the appropriate level of hydraulic cylinder expansion, taking into account the amount of ground heaving and the allowable displacement of the pile.