• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.232-236
• /
• 2000

To provide model parameters for servo control system design, dynamic characteristics of a piezoelectric microactuator for hard disk drive(HDD) were investigated. At first frequency response characteristics was measured and a second order model was proposed. Here the amplitude dependent dynamic characteristics such as low frequency gain and damping ratio were studied. In addition, the load current and equivalent impedance of the piezoelectric actuator were measured by varying excitation voltage and frequency. At last, the super-harmonic resonance of the piezoelectric actuator was discussed.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.887-891
• /
• 2003

In this paper, two filters with center frequency of 19.58MHz were cascaded and its bandwidth characteristics were investigated with the variations of coupling capacitance for intermediate frequency (IF) bandpass filter application. The cascaded filter showed the higher stop region, reduction of spurious response and increase of selectivity. With the increase of coupling capacitance, insertion loss was increased but spurious response reduced. The cascaded filter with coupling capacitance of 15pF showed insertion loss of 5.643dB, 3dB bandwidth of 55.089kHz and 20dB bandwidth of 83.608kHz, respectively.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.5
• /
• pp.959-964
• /
• 2018

In this paper, it was firstly confirmed that the drain current of the depleted SOI MOSFET operated in the high frequency response delay occurs by the inductive parasitic. Depleted SOI MOSFET cannot be applied as a conventional high-frequency MOSFET model because the response delay of the drain current is generated in accordance with the drain voltage fluctuation. This response delay may be described as a non-quasi-static effect, and the SOI MOSFET generated the response delay by the inductive parasitics compared to typical MOSFET. It is confirmed that depleted SOI MOSFET's RF characteristics can be well reproduced with the proposed method including the drain current response delay.

• Journal of Advanced Marine Engineering and Technology
• /
• v.17 no.4
• /
• pp.87-99
• /
• 1993

Nowadays, the cartridge valve can be controlled proportionally in remote place by adopting proportional solenoid and it becomes widely used as control component in hydraulic systems. Especially, multi stage proportional valve is attractive because it consumes less input power though its characteristics might slightly be defected. But, the system parameter should be carefully chosen to obtain optimistic characteristics. This study concerning three stage proportional throttle control valve is purposed to examine the influences of paameters to the dynamic characteristics. The typical transient and frequency responses of proportional throttle control valve were inspected through the experiments and compared to those derived from the theoritical analyses. And it was confirmed that the analyses are appropriate. Then the influences of various system parameters to the dynamic characteristics were examined by means of simulations. For the analyses, the basic equations derived from lumped model were linearized and the linearized equations were transformed to the transfer functions between inputs and outputs. Then the transient responses and frequency responses were obtained from transfer functions. 1. It is appropriate to estimate the dynamic characteristics of valve which has relatively sophisticated structure by means of system analyses using linearized equations. 2. Though the valve has two pilot stages, fairly good characteristics can be obtained by carefully choosing system parameters. 3. Main valve very quickly follows the movement of second pilot valve when the parameters of main valve(the oil supply passage and discharge passage fpr second pilot valve) are appropriately chosen.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.25 no.5
• /
• pp.223-232
• /
• 2021

The spatial variation characteristics of seismic motions at the nuclear power plant's site and structures were analyzed using earthquake records obtained at the Fukushima nuclear power plant during the Great East Japan Earthquake. The ground responses amplified as they approached the soil surface from the lower rock surface, and the amplification occurred intensively at about 50 m near the ground. Due to the soil layer's nonlinear characteristics caused by the strong seismic motion, the ground's natural frequency derived from the response spectrum ratio appeared to be smaller than that calculated from the shear wave velocity profile. The spatial variation of the peak ground acceleration at the ground surface of the power plant site showed a significant difference of about 0.6 g at the maximum. As a result of comparing the response spectrums at the basement of the structure with the design response spectrum, there was a large variability by each power plant unit. The difference was more significant in the Fukushima Daiichi site record, which showed larger peak ground acceleration at the surface. The earthquake motions input to the basement of the structure amplified according to the structure's height. The natural frequency obtained from the recorded results was lower than that indicated in the previous research. Also, the floor response spectrum change according to the location at the same height was investigated. The vertical response on the foundation surface showed a significant difference in spectral acceleration depending on the location. The amplified response in the structure showed a different variability depending on the type of structure and the target frequency.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.3
• /
• pp.128-133
• /
• 2008

In this paper, in order to analyze property of frequency response in microphone using optical sensor, acousto-optic sensor system has been implemented. The capacitance microphone and fiber-optic transmission path type fiber-optic microphone (FOM) have weaknesses in directivity, size, weight, and price. However suggested optical microphone can be constituted by cheap devices, so it has many benefits like small size, light weight, high directivity, etc. Head part of optical microphone which is suggested in this paper is movable back and forth by sound pressure with the attached reflection plate. Operating point has also been determined by measuring the response characteristics. The choosing the point, which has maximum linearity and sensitivity has changing the distance between optical head and vibrating plate. We measured the output of the O/E transformed signal of the optical microphone while frequency of sound signal is changed using sound measurement /analysis program, "Smaart Live" and "USBPre", which are based on PC, and compared the result from an existing capacitance microphone. The measured optical microphone showed almost similar output characteristics as those of the compared condenser microphone, and its bandwidth performance was about 4 kHz at up to 3 dB.

• Computational Structural Engineering
• /
• v.10 no.4
• /
• pp.185-193
• /
• 1997

A major problem of frequency analysis in the field of low-frequencies such as building or construction vibration is the way of signal processing which is appropriate to obtain included frequency content from the finite process to be measured. Therefore, it is the aim of the investigation reported herein to develop the signal processing algorithm which is analyzed without losing the reliability of the measurements in low-frequency domain. To accomplish the research objective, it was analyzed the problems on the way of signal processing in low-frequency domain, and compared the response characteristics of FFT with those of MEM (Maximum Entropy Method) about the low-frequency of vibration. This evaluation of the response characteristics is used in determining appropriate signal processing algorithm into the low-frequency domain.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2000.04b
• /
• pp.431-438
• /
• 2000

The cost function consists of the weighting functions concerning the structural responses to be controlled and the controller capability. Therefore, the control efficiency depends on the characteristics of the weighting functions. The objective of this paper is the comparative study of the time domain control strategies of LQR and LQG and the frequency domain strategy of H₂ by setting the equivalent weighting functions to the all control strategies. As a result of analysis, LQR strategy is found to be more efficient than other strategies in terms of the response reduction. but the control force is found to be a little highter. As LQG can compensate the limitation of LQR that all state variables should be identified, LQG is more acceptable algorithm than LQR. Furthermore LQG shows a good performance both in the response reduction and the control force. Finally H₂ algorithm is employed to illustrate the importance of weighting filters considering the frequency characteristics of the response and the controller. It Is shown that the H₂ algorithm is found to be the most effective one for the response control with a little control force having a low frequency band.

• Wind and Structures
• /
• v.5 no.1
• /
• pp.61-80
• /
• 2002

Wind tunnel aeroelastic model tests of the Commonwealth Advisory Aeronautical Research Council (CAARC) standard tall building were conducted using a three-degree-of-freedom base hinged aeroelastic(BHA) model. Experimental investigation into the effects of coupled translational-torsional motion, cross-wind/torsional frequency ratio and eccentricity between centre of mass and centre of stiffness on the wind-induced response characteristics and wind excitation mechanisms was carried out. The wind tunnel test results highlight the significant effects of coupled translational-torsional motion, and eccentricity between centre of mass and centre of stiffness, on both the normalised along-wind and cross-wind acceleration responses for reduced wind velocities ranging from 4 to 20. Coupled translational-torsional motion and eccentricity between centre of mass and centre of stiffness also have significant impacts on the amplitude-dependent effect caused by the vortex resonant process, and the transfer of vibrational energy between the along-wind and cross-wind directions. These resulted in either an increase or decrease of each response component, in particular at reduced wind velocities close to a critical value of 10. In addition, the contribution of vibrational energy from the torsional motion to the cross-wind response of the building model can be greatly amplified by the effect of resonance between the vortex shedding frequency and the torsional natural frequency of the building model.

• Interaction and multiscale mechanics
• /
• v.5 no.1
• /
• pp.75-90
• /
• 2012

This paper investigates the effects of sports ground materials on the transfer characteristics of the landing impact force using a coupled foot-shoe-ground interaction model. The impact force resulting from the collision between the sports shoe and the ground is partially dissipated, but the remaining portion transfers to the human body via the lower extremity. However, since the landing impact force is strongly influenced by the sports ground material we consider four different sports grounds, asphalt, urethane, clay and wood. We use a fully coupled 3-D foot-shoe-ground interaction model and we construct the multi-layered composite ground models. Through the numerical simulation, the landing impact characteristics such as the ground reaction force (GRF), the acceleration transfer and the frequency response characteristics are investigated for four different sports grounds. It was found that the risk of injury, associated with the landing impact, was reduced as the ground material changes from asphalt to wood, from the fact that both the peak vertical acceleration and the central frequency monotonically decrease from asphalt to wood. As well, it was found that most of the impact acceleration and frequency was dissipated at the heel, then not much changed from the ankle to the knee.