• Journal of Advanced Navigation Technology
• /
• v.23 no.2
• /
• pp.134-141
• /
• 2019

Radar systems are divided into the pulse Doppler (PD) radar and the frequency modulated continuous wave (FMCW) radar depending on the transmission waveform. In particular, the PD radar is advantageous for long-range target detection, and the FMCW radar is suitable for short-range target detection. In this paper, we present design and implementation results for a multi-mode radar signal processor (RSP) that can support both PD and FMCW radar systems to detect unmanned aerial vehicles (UAVs) at short distances as well as long distances. The proposed radar signal processor can be implemented based on Altera Cyclone-IV FPGA with 19,623 logic elements, 9,759 registers, and 25,190,400 memory bits. The logic elements and registers of the proposed radar signal processor are reduced by approximately 43% and 30%, respectively, compared to the sum of logic elements and registers of the conventional PD radar and FMCW radar signal processor.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.4
• /
• pp.611-614
• /
• 2021

In this paper, we propose a widerange array microphone for lecturer tracked with Frequency Modulated Continuous Waveform (FMCW) radar sensor. Time Difference-of-Arrival (TDoA) is often used as audio tracking, but the tracking accuracy is poor because the frequency of the voice is low and the relative frequency change is large. FMCW radar has a simple structure and is used to detect obstacles for vehicles, and the resolution can be archived to several centimeter. It is shown that the sensor is useful for detecting a speaker in open area such as a lecture, and we propose an wide range 4-element array microphone beamforming system. Through some experiments, the proposed system is able to adequately track the location and showed a 8.6dB improvement over the selection of the best microphone.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.2
• /
• pp.254-262
• /
• 2016

With the increased demand for automotive radar systems, mutual interference between vehicles has become a crucial issue that must be resolved to ensure better automotive safety. Mutual interference between frequency modulated continuous waveform (FMCW) radar system appears in the form of increased noise levels in the frequency domain and results in a failure to separate the target object from interferers. The traditional fast fourier transform (FFT) algorithm, which is used to estimate the beat frequency, is vulnerable in interference-limited automotive radar environments. In order to overcome this drawback, we propose a high-resolution frequency estimation technique for use in interference environments. To verify the performance of the proposed algorithms, a 77GHz FMCW radar system is considered. The proposed method employs a high-resolution algorithm, specially the multiple signal classification and estimation of signal parameters via rotational invariance techniques, which are able to estimate beat frequency accurately.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.784-790
• /
• 2009

A forward-looking automotive radar typically utilizes the frequency modulated continuous wave(FMCW) or pulsed-Doppler waveform for the Information acquisition of the target range and velocity. In order to obtain the high resolution target information, however, a narrow pulse width and wide bandwidth are inherently required, thus resulting in high peak power and high speed digital converter processing. In this paper, a stepped-frequency pulsed-Doppler(SFPD) waveform algorithm is proposed for high resolution forward looking automotive radar application. The performance of the proposed SFPD waveform technique is analyzed and compared with the conventional FMCW and PD method. Since this technique can be used for the high resolution target imaging with arbitrary range and Doppler resolution, it is expected to be useful In automotive radar target classification for the precision collision avoidance applications in the future.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.4
• /
• pp.377-387
• /
• 2016

Design of X-band frequency FMCW based imaging radar with multi-resolutions and performances of the self-manufactured radar system are presented in this study. In order to implement the multi-bandwidths, a ramp sequence of the FMCW signal is consisting of two kinds of 'saw-tooth' waveform with different bandwidth, and a receiver circuit consisting of L-band source and frequency converter circuit is used to effectively extract spectra of beat-frequency from the received signal of X-band frequency. The system setups for performance measurement of self-manufactured radar system are maximum output power of 35 dBm, sampling frequency of 1.2 MHz and sweep time of 1 ms. Then, the measured resolutions of the modulated signal having bandwidth of 500 MHz and 300 MHz in range & azimuth-direction are (0.28 m, 0.26 m) and (0.44 m, 0.27 m), respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1109-1115
• /
• 2010

FMCW(Frequency Modulation Continuous Wave) Radar can detect the distance and the velocity of forward obstacles using linearly modulated FM signal. For better performance, the RF of radar should be operated with wideband frequency linearity on 300 MHz bandwidth at 77 GHz carrier frequency. In this paper, we propose a simple method for improving frequency linearity of FMCW radar implemented with VCO. The proposed method shows that the Voltage-Frequency relation of VCO could be measured by using the modified Tx waveform of FMCW radar. Then the measured nonlinearity could be compensated using LUT(Look-up Table) with easy. It is noted that the proposed can be adopted in existing system without extra circuit.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.22 no.6
• /
• pp.43-49
• /
• 2022

FMCW(Frequency Modulated Continuous Wave) Radar is very useful for vehicle collision warning system and autonomous driving sensor. In this paper, the design and implementation of FMCW radar based on two chip MMIC developed as an autonomous driving sensor was described. Especially, generation of frame-based and chirp-based waveform generation and signal processing are mixed to have the strength of maximum detection speed and compensation of speed. This implemented system was analyzed for performance and commercialization potential through lab. test and driving test in K-city.

• Journal of the Korea Society for Simulation
• /
• v.27 no.4
• /
• pp.61-68
• /
• 2018

This paper deals with ground clutter model for FOD (foreign object debris) surveillance FMCW (frequency modulated continuous waveform) radar. In the FOD surveillance radar, it has received not only the signals reflected by FOD, but also the clutters of the surface of the runway and the grassland simultaneously. However, to detect the FOD, the clutter rejection algorithm is necessary because the RCS (radar cross section) of FOD is nearly same to RCS of the grassland. In addition, it is difficult to apply the MTI (moving target indicator) algorithm as the clutter rejection algorithm because both the FOD and the clutter coexist stationarily. Hence, to remove the stationary clutter, it is crucial to accurately generate clutter map considering the surface of road. In this paper, in order to generate the clutter map, the respective beat signal at every range bin is generated in the case of only the surface without FOD, and then the beat signal accumulated 100 times. And also, Weibull distribution is applied to the RCS value to take the scattering distribution of clutter into consideration. The simulation results show that FOD can be well detected by applying the generated clutter map to the FOD FMCW radar.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.6
• /
• pp.51-57
• /
• 2017

In this paper, we designed a frequency synthesizer using DDS (Direct Digital Synthesizer) for Ka-band compact Radar. DDS is applied to generate various waveform and to cover high-speed frequency sweep. In order to reduce size, waveform generator and Ka band frequency up-converter are integrated in one module. Proposed frequency synthesizer provides LFM(Linear Frequency Modulation) waveform and Phase modulated FMCW (Frequency Modulation Continuous Wave) waveform. It is observed that fabricated synthesizer performs $0.191{\mu}sec$ frequency switching time and -89.16 dBc/Hz phase noise at offset 1 kHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.11
• /
• pp.1304-1310
• /
• 2010

This study is to design FMCW radar transceiver of K-band which is used to detect and track approaching high speed targets with low altitude. The transmitter needs high output power due to small RCS targets and wide beamwidth of transmit antenna. Multi-channel receivers are required to detect and track targets by interferometer method. Transmitter consists of high power amplifier, waveguide switch, and frequency up-converter. Receiver is composed of five channel receivers, up and down converters, X-band local oscillator and waveform generator. Before manufacturing it, the proposed architecture of transceiver is proved by modeling and simulation using several parameters. Then, it is manufactured by using industrial RF components. The performance parameters are measured through experiment. In the experiment, transmitting power and receiver gain were measured with 39.64 dBm and 29.1 dB, respectively. All other parameters in the specification were satisfied as well.