• 소성∙가공
• /
• 제9권2호
• /
• pp.152-158
• /
• 2000

A finite element analysis has been performed to investigate the effect of die clearance on shear planes in the fine blanking of a part of automobile safety belt. For the analysis, S45C is selected as an material, which is used in manufacturing the part of automobile safety belt, and Cockcroft-Latham fracture criterion is applied. Effect of die Clearance on die-roll width, die-roll depth, burnish zone, and fracture zone has been investigated in the finite element analysis by a rigid-plastic FEM code, DEFORM-2D. From the analysis, it has been found that die-roll depth and depth of the shear plane increase with increasing die clearance. And the burnish zone decreases with increasing die clearance, but the variation of fracture zone is opposite to that of burnish zone because the increase in die clearance requires less fracture energy. Theoretical predictions are compared with experimental results. There is a good agreement between theory and experiment.

• Computers and Concrete
• /
• 제7권1호
• /
• pp.39-51
• /
• 2010

The system of pores of autoclaved aerated concrete (AAC) is described by the so-called cherry-pit model, a random system of partially interpenetrating spheres. For the simulation of fracture processes, the solid phase is approximated by an irregular spatial network of beams obtained by means of the so-called radical tessellation with respect to the pore spheres. FE calculations using standard software (ANSYS) yield the strain energies of the beams. These energies are used as fracture criterion according to which highly loaded beams are considered as broken and are removed from the network. The paper investigates the relationship between mean fracture strength and microstructure for structures close to real AAC samples and virtual structures with particular geometrical properties.

• Computers and Concrete
• /
• 제18권3호
• /
• pp.337-354
• /
• 2016

To study the influence on fracture properties of reinforced concrete wedge splitting test specimens by the addition of reinforcement, and the restriction of steel bars on crack propagation, 7 groups reinforced concrete specimens of different reinforcement position and 1 group plain concrete specimens with the same size factors were designed and constructed for the tests. Based on the double-K fracture criterion and tests, fracture toughness calculation model which was suitable for reinforced concrete wedge splitting tensile specimens has been obtained. The results show that: the value of initial craking load Pini and unstable fracture load Pun decreases gradually with the distance of reinforcement away from specimens's top. Compared with plain concrete specimens, addition of steel bar can reduce the value of initial fracture toughness KIini, but significantly increase the value of the critical effective crack length ac and unstable fracture toughness KIun. For tensional concrete member, the effect of anti-cracking by reinforcement was mainly acted after cracking, the best function of preventing fracture initiation was when the steel bar was placed in the middle of the crack, and when the reinforcement was across the crack and located away from crack tip, it plays the best role in inhibiting the extension of crack.

• Steel and Composite Structures
• /
• 제1권4호
• /
• pp.411-426
• /
• 2001

This paper treats the failure analysis of prestressing steel wires with different kinds of localised damage in the form of a surface defect (crack or notch) or as a mechanical action (transverse loads). From the microscopical point of view, the micromechanisms of fracture are shear dimples (associated with localised plasticity) in the case of the transverse loads and cleavage-like (related to a weakest-link fracture micromechanism) in the case of cracked wires. In the notched geometries the microscopic modes of fracture range from the ductile micro-void coalescence to the brittle cleavage, depending on the stress triaxiality in the vicinity of the notch tip. From the macroscopical point of view, fracture criteria are proposed as design criteria in damage tolerance analyses. The transverse load situation is solved by using an upper bound theorem of limit analysis in plasticity. The case of the cracked wire may be treated using fracture criteria in the framework of linear elastic fracture mechanics on the basis of a previous finite element computation of the stress intensity factor in the cracked cylinder. Notched geometries require the use of elastic-plastic fracture mechanics and numerical analysis of the stress-strain state at the failure situation. A fracture criterion is formulated on the basis of the critical value of the effective or equivalent stress in the Von Mises sense.

• 치과방사선
• /
• 제22권1호
• /
• pp.7-22
• /
• 1992

The stress distributions on a human mandible for 18 load cases under two different boundary conditions (mouth open and closed), using the three dimensional finite element modeling were studied. Also, the expected fracture loads for each load cases were calculated by using the Von-Mises yield criterion. The model of a mandible with all teeth was composed of 2402 hexahedron elements and 3698 nodes. CAD techniques were used to analyze the 3-dimensional results. The conclusions of this study were as follows: 1. In the mouth open state, the maximum stress occured at the condyle neck; when the lateral load was exerted, the maximum stress occured at the load side condyle. 2. In the mouth closed state, when the loads were exerted on the mandibular body and chin, the maximum stress occured at the loaded area, and when the loads were exerted on the angle and ramus, the maximum stress occured at the condyle neck. 3. The expected fracture loads in each load case were calculated using the Von-Mises yield criterion, and it was confirmed that the mandible in the mouth open state was more easily fractured than that in the mouth closed state, and the expected fracture loads are lesser in the cases that load direction is parallel at mandibular plane than 45°. 4. The magnitudes of the expected fracture loads increased in the order of angle, ramus, body and chin in case of the mouth closed state, while chin, body, angle and ramus in case of the mouth open state. 5. The Von-Mises stress concentration regions analyzed by F.E.M. corresponded well with the results of clinical studies.

• Structural Engineering and Mechanics
• /
• 제74권6호
• /
• pp.723-735
• /
• 2020

This study is reported the adhesion failure in adhesive bonded composite and specifically for the T-joint structure. Three-dimensional finite element analysis has been performed using a commercial tool and the necessary outcomes are obtained via an eight noded solid element (Solid 185-element) from the library of ANSYS. The structural analysis input has been incurred through ANSYS parametric design language (APDL) code. The normal and shear stress distributions along different layers of the joint structure have been evaluated as the final outcomes. Based on the stress distributions, failure location in the composite joint structure has been identified by using the Tsai-Wu stress failure criterion. It has been found that the failure index is maximum at the interface between flange and web part of the joint (top layer) which indicates the probable location of failure initiation. This kind of failures are considered as adhesion failure and the failure propagation is governed by strain energy release rate (SERR) of fracture mechanics. The different adhesion failure lengths are also considered at the failure location to calculate the SERR values i.e. mode I fracture (opening), mode II fracture (sliding) and mode III fracture (tearing) along the failure front. Also, virtual crack closure technique (VCCT) principle of fracture mechanics steps is used to calculate the above said SERRs. It is found that the mode I SERR is more dominating compared to other two modes of failure for the joint considered. Finally, the influences of various parametric (geometrical and material) effect on SERR of the joint structure are evaluated and discussed in details.

• 대한기계학회논문집A
• /
• 제38권8호
• /
• pp.917-923
• /
• 2014

휴대폰과 같은 전자제품의 소형화로 체결 부품도 소형화가 요구된다. 초소형 볼트의 머리부분 두께 감소 요구에 따라 체결시 볼트 머리부 파손으로 충분한 체결력을 확보하는데 어려움이 있다. 본 연구에서는 볼트 깊이에 따른 체결 토크를 해석적으로 예측하여 비트 형상 설계에 활용하고자 한다. 볼트 머리부는 주로 전단 파손이 발생하기 때문에, 볼트용 선재의 전단 실험을 통하여 파손 기준을 설정하였다. 그리고, 설정된 전단파손 기준을 바탕으로 체결시 파손 형상과 최대 체결 토크를 예측하였다. 또한, 머리부에 성형되는 비트의 깊이에 따른 최대 체결토크을 예측하였다. 비트 깊이가 깊을수록 볼트 머리와 나사부의 경계에서 응력 집중으로 파손이 빨리 발생하고, 최대 체결 토크도 작아짐을 알 수 있었다.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.876-888
• /
• 1986

본 논문에서는 자유 표면과 강체부분이 많은 피어싱 공정의 해석에서 발생하 는 해의 수렴성 저하를 방지하기 위하여 비정상 상태의 가공경화 효과와 강체 연속처리 리방법을 프로그램 개발에 적용하고 프로그램 개발에 적용하고 프로그램 범용성을 높 이기 위해 초기 속도장 발생 프로그램을 개발하여 본 공정 해석에 적용하여 보려고 한 다. 또한 재료를 가공 경화를 고려한 강소성체(rigid-plastic material)로 가정해서 시편에 크랙이 발생하여 파괴될때까지 컴퓨터 시뮬레이션을 수행한 후 냉간 피어싱 공 정에 있어서 표면 크랙의 발생과 성장 그리고 파괴에 가장 많은 영향을 미치는 인자들 을 계산결과를 토대로 실험과 비교조사하고, 실험 시편의 지름과 높이 그리고 마찰상 태를 다르게 조합해서, 실험과 계산을 시하여 시편 모양에 따른 변형 모우드(mode)와 파괴 모우드의 차이를 규명해 보기로 한다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1754-1759
• /
• 2007

Propagation of a mixed-mode crack in Soda-Lime silica glass using Movable Cellular Automata (MCA) method is demonstrated in this study. In MCA method, special fracture criterion is used to describe the process of crack initiation and propagation. Comparison between MCA and other crack initiation criteria results are made. The crack resistance curves and bifurcation angles under different loading angles are found. In comparisons with results of maximum circumferential tensile stress criterion, MCA result showed the sufficient agreement.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.179-181
• /
• 2003

The present study focuses on the effect of geometrical discontinuity, strength mismatch, which can elevate plastic constraint due to heterogeneous plastic straining, and loading rate on the ductile crack initiation using two-parameter criterion. Fracture initiation testing has been conducted under static and dynamic loading using circumferentially notched round-bar specimens. In order to evaluate the stress/strain state in the specimens, especially under dynamic loading, a thermal elastic-plastic dynamic finite element (FE) analysis considering the temperature rise due to plastic deformation has been carried out.