• Proceedings of the KIEE Conference
• /
• 2001.11b
• /
• pp.118-120
• /
• 2001

This paper presents a distance relaying algorithm based on the Discrete Fourier Transform(DFT) for elimination of DC-Offset. When the DFT is applied to current signal. the real and imaginary parts of fundamental component consist of fundamental component itself and DC-Offset. The DC-Offset is calculated by four consecutive values of the imaginary components, so that the fundamental component can be accurately estimated. Performance evaluation is presented for A-phase ground faults on 154kV 80km overhead transmission line. The proposed algorithm is inspected by software simulation and hardware simulation.

• Food Science and Preservation
• /
• v.9 no.4
• /
• pp.396-399
• /
• 2002

An attempt was made in this study to investigate the optimum extracting time from meat with bone of goat and the nutritional component of its extract. for the trials, the mixtures of meat with bone and water were adjusted to the ratios of five to four by weight and extracted for 6, 9 and 12 hours at 120$\^{C}$ under autoclave. Judging from the content of mineral and amino acid, nonenzymatic browning and yield, the optimum extracting time was 9 hours. The major components of mineral were composed of 47.7mg％ potassium, 12.7mg% calcium, 150.0mg% sodium, 105.3mg% phosphorus and 0.5mg% iron, and of amino acids composed of 1,308.0mg% glutamic acid, 1,464.2mg% glycine, 750.2mg% alanine and 828.lmg% proline in extract. The yield of extract was 32.1 percentage by dry basis.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.20 no.3
• /
• pp.35-43
• /
• 2012

Medium size rotorcraft consist of approximately 5,000 key components. The components must satisfy the target weight and performance requirement through optimization. Therefore a rotorcraft component has approximately 100 times higher unit cost for mass production than the equivalent of an automobile's, along with huge development cost. Configuration management consists of four main parts : configuration identification, configuration control, configuration audit, and data management. In development programme, configuration management is one of the methods to save development cost, and setting a well-structured configuration management system according to the Military Standard is an important factor in success of the programme. The paper proposes a configuration management system suitable for development of various multi-use components development and presents that the configuration management was performed successfully during dual-use component development programme using the established system.

• Journal of Power System Engineering
• /
• v.6 no.1
• /
• pp.27-35
• /
• 2002

In this paper, the effect of oxygen component in fuel on the exhaust emissions has been investigated for direct injection diesel engine. It is tested to estimate change of engine performance and exhaust emission characteristics for the commercial diesel fuel and oxygenate blended fuel which has four kinds of mixed ratio. And, the effects of exhaust gas recirculation(EGR) on the characteristics of NOx emission and brake specific fuel consumption rate have been investigated. Dimethyl carbonate(DMC) contains oxygen component 53.3% in itself, and it is a kind of effective oxygenated fuel of carbonate group that the smoke emission of DMC is reduced remarkably in comparison with commercial diesel fuel, that is, it can supply oxygen component sufficiently at higher loads and speeds in diesel engine. It was found that simultaneous reduction of smoke and NOx was achieved with oxygenated fuel and EGR method.

• Korean Journal of Agricultural Science
• /
• v.8 no.2
• /
• pp.139-151
• /
• 1981

To obtain breeding materials 57 Korean local corn lines collected were assessed and classified by the application of principal component analysis. The results obtained were as follows. 1. In the result of principal component analysis for 27 characters, 67.1% and 88.6% of total variation could be appreciated by the first four and fir st ten principal component respectively. 2. According to the value of characters and principal components, contribution of characters to principal components were very variable. 3. Biological meaning of the principal component and plant type corresponded to the each principal component were explained clear by the correlation coefficients between principal components and characters. 4. 57 lines were classified into 4 lineal groups by the taxonomic distances.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.6
• /
• pp.771-780
• /
• 2010

This paper describes the design process of a six-component force/torque (F/T) sensor. The new six-component F/T sensor having leaf spring ends has been developed using a cross beam structure as the basic sensing element. Fundamental strain analysis of both ends fixed beam having a leaf spring structure is performed by finite element analysis. In order to obtain similar output sensing strains from the six component loads and minimize coupling strains, the optimal location of strain gages is determined and the strain gages are connected so that the bridge circuits with four strain gages would be balanced. Using leaf spring ends instead of rigid fixed ends, remarkable increment in output sensing strain can be achieved for two component forces. Several modifications in design result in a similar sensing strain of approximately $400\;{\mu}m/m$ for the six-component forces and moments, and a reduced coupling strain of $0\;{\mu}m/m$ between the forces and moments.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.11a
• /
• pp.89-92
• /
• 2000

Non-aqueous tape casting of LTCC with PVB binder has been studied in a continuous tape casting machine. The aim of the study was to evaluate this type of system in the different Binder/Plasticizer and solid content compositions. Each four slurry compositions were used in the experiments with varied binder/plasticizer and solid content. All the slurries gave good quality tapes with smooth surfaces without blisters or pinholes. The highest mechanical properties was obtained for the B/P=3.0, powder content 70vol% composition from 52 ${\mu}{\textrm}{m}$ green tapes, a tensile strength of 4.6 MPa and a linear extension of 29.5%

• Journal of Applied Reliability
• /
• v.15 no.4
• /
• pp.233-240
• /
• 2015

We analyse reliability of multi-state UH-60 helicopter hydraulic pump system with a multi-functional standby component using Markov analysis method. The system consists of seven components: 2 main pumps, 1 standby pump, 2 primary servos, and 2 tail rotor servos. The standby pump can take over when one more than components fail. Therefore the standby pump is multi-functional standby component. The system has four states: good, deteriorated, dangerous, and failed. The components have 2 states: working and failed. We assume the system is unrepairable when the components fail. We estimate failure distributions and rates using collected failure time data in field. And we classify multi-state of the system according to emergency procedure of UH-60A student handout. We obtain the reliabilities of multi-state system using Visual Basic program because the differential equations is extremely complicated and tedious to solve.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.1
• /
• pp.25-37
• /
• 2002

The purpose of the study was to survey the distribution patterns of inorganic elements of PM-10 in the various indoor environments and analyze the pollution patterns of aerosol in various places of indoor environment using a pattern recognition method based on cluster analysis and disjoint principal component analysis. A total of 40 samples in the indoor had been collected using mini-vol portable samplers. These samples were analyzed for their 19 bulk inorganic compounds such as B, Na, Mg, Al, K, Ca, Ti, V, Cr, Fe, Ni, Cu, Zn, As, Se, Cd, Ba, Ce, and Pb by using an ICP-MS. By applying a disjoint principal component analysis, four patterns of the indoor air pollutions were distinguished. The first pattern was identified as a group with high concentrations of PM-10, Na, Mg, and Ca. The second pattern was identified as a group with high concentrations B, Mg, At, Ca, Fe, Cu, and Ba. The third pattern was a group of sites with high concentrations of K, Zn. Cd. The fourth pattern was a group with low concentrations PM-10 and all inorganic elements. This methodology was found to be helpful enough to set the criteria standard of indoor air quality, corresponding pollutants, and classification of indoor environment categories when making an indoor air quality law.

• Journal of The Korean Astronomical Society
• /
• v.19 no.1
• /
• pp.33-49
• /
• 1986

Radial distribution of internal density has been determined for thirteen subclouds in the three giant molecular cloud complexes accompanying Mon OB1, Mon OB2 and CMa OB1 associations, We modeled their radial density structures with the density distribution of isothermal gas spheres. Most of the subclouds, nine out of the thirteen, are well described by isothermal spheres of single component; while the rest four require an additional component. Total mass and potential energy of each subcloud are also derived from the radial density structure; thermal energy and internal velocity dispersion required for sustaining the density structure are deduced from the isothermal gas model. Our derived masses of the clouds are comparable to the values determined by Blitz (1978) under LTE assumption. This agreement suggests that the correction factor for non-LTE effect on mass-estimate is not far from unity. The ratio of the gravitational potential energy to the kinetic energy of thermal motion is as large as 250; hence the thermal motion alone cannot support these clouds against the gravity. Being supported by turbulence motion with velocities of six to seven times the thermal velocity, the clouds of one-component type seem to be in equilibrium with the gravity; while the clouds of two-component type are likely to be in the stage of gravitational collapse.