• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.85-92
• /
• 2007

This paper presents a design optimization of a new Advanced Active Blade Twist (AATR-II) blade incorporating single crystal Macro Fiber Composites (MFC) and conducts vibratory loads reduction analysis using an obtained optimal blade configuration. Due to the high actuation performance of the single crystal MFC, the AATR blade may reduce the helicopter vibration more efficiently even with a lower input-voltage as compared with the previous ATR blades. The design optimization provides the optimal cross-sectional configuration to maximize the tip twist actuation when a certain input-voltage is given. In order to maintain the properties of the original ATR blade, various constraints and bounds are considered for the design variables selected. After the design optimization is completed successfully, vibratory load reduction analysis of the optimized AATR-II blade in forward flight condition is conducted. The numerical result shows that the hub vibratory loads are reduced significantly although 20% input-voltage of the original ATR blade is used.

• 한국전산유체공학회지
• /
• 제16권4호
• /
• pp.21-27
• /
• 2011

In this paper, the diagonal implicit harmonic balance method is applied to analyze helicopter rotor blade flow. The periodic boundary condition for Fourier coefficients is also applied in hover and forward flight conditions. It is available enough to simulate the forward flight problem with only one rotor blade using the periodic boundary condition in the frequency domain. In order to demonstrate the present method, Caradonna & Tung's rotor blades were used and the results were compared to the time-accurate method and experimental data.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 학술대회
• /
• pp.251-255
• /
• 2008

Flow field around helicopter involves incompressible flow near the blade root and compressible flow at the blade tip. A problem occurs for low Mach number flow due to the stiffness of the governing equations. Time-derivative preconditioning techniques have been incorporated to reduce the stiffness that occurs at low speed region. The preconditioned form of the compressible Navier-Stokes and Euler equations is used. Computations are performed for the Caradonna-Tung's hovering and non-lifting forward flight case. Computational results are in good agreement with the experimental data.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년 추계학술대회논문집
• /
• pp.251-255
• /
• 2008

Flow field around helicopter involves incompressible flow near the blade root and compressible flow at the blade tip. A problem occurs for low Mach number flow due to the stiffness of the governing equations. Time-derivative preconditioning techniques have been incorporated to reduce the stiffness that occurs at low speed region. The preconditioned form of the compressible Navier-Stokes and Euler equations is used. Computations are performed for the Caradonna-Tung's hovering and non-lifting forward flight case. Computational results are in good agreement with the experimental data.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2011년 춘계학술대회논문집
• /
• pp.543-549
• /
• 2011

In this paper, diagonal implicit harmonic balance method is applied to analyze helicopter rotor blade flow. Periodic boundary condition for Fourier coefficients is also applied in hover and forward flight condition. It is available enough to simulate the forward flight problem with only one rotor blade using the periodic boundary condition in frequency domain. In order to demonstrate present method Carodonna & Tung's rotor blades are used and the results are compared to time-accurate method and experimental data.

• Journal of Biosystems Engineering
• /
• 제28권1호
• /
• pp.19-26
• /
• 2003

An oscillating digger mechanism was designed, constructed. and tested. The mechanism is consisted of a six-bar linkage, one four-bar linkage was fer the digger blade and the other one fur variable soil-crop separation. Experimental variables were amplitude(3, 6, 9 mm). frequency(11.2, 14.9. 17.0 Hz), and forward speed of tractor(0.91, 1.13, 1.56 km/h). Each combination of these variables was replicated three times to measure the draft and torque for power requirement evaluation. and the broken-up soil height on the soil separation sieve mechanism. Four parameters λ(the ratio of vibration speed to forward velocity), p(the ratio of vibration acceleration to forward velocity), K(the ratio of vibration acceleration to gravitational acceleration), and T(the product of λ and K) were induced from three experimental variables: amplitude, frequency, and tractor speed. And the power requirement and soil separation ability were analyzed by regression. Though λ and K were known to be the representative parameters. T was the most moderate one to explain draft. torque. and soil separation in this study. It was estimated that the T equal to or greater than 2.4 was the minimum recommended value. Figure 18 would be useful fir the selection of amplitude. frequency, or operating tractor speed once any two variables are known.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2013년도 춘계학술대회 논문집
• /
• pp.340-346
• /
• 2013

This paper describes a helicopter vibration induced by main rotor in forward flight. The hub loads in the fixed frame, which are dominant source of helicopter vibration, are obtained by multi-blade summation of rotating blades loadings. The components of 3/rev, 4/rev, and 5/rev blades loadings are transmitted by blades to 4/rev hub loads in the fixed frame. The vertical vibrations of helicopter at pilot seat and copilot seat are calculated through rigid body transfer functions considering airframe to be rigid body. The blades are assumed to be elastic and undergo the flap, lag, and torsion motion and free wake aerodynamic model is used to calculate the precise blade loadings in the analysis. The 4/rev vertical vibration responses are analyzed from rotating blade loadings and fixed hub loadings.

• Journal of Mechanical Science and Technology
• /
• 제18권8호
• /
• pp.1401-1417
• /
• 2004

Experimental and computational studies were performed to determine the effects of different blade designs on a flow pattern inside a double-spindle counter rotating mower deck. In the experimental study, two different blade models were tested by measuring air velocities using a forward-scatter LDV system. The velocity measurements were taken at several different azimuth and axial sections inside the deck. The measured velocity distributions clarified the air flow pattern caused by the rotating blades and demonstrated the effects of deck and blade designs. A high-speed video camera and a sound level meter were used for flow visualization and noise level measurement. In the computational works, two-dimensional blade shapes at several arbitrary radial sections have been selected for flow computations around the blade model. For three-dimensional computation applied a non-inertia coordinate system, a flow field around the entire three-dimensional blade shape is used to evaluate flow patterns in order to take radial flow interactions into account. The computational results were compared with the experimental results.

• 한국항공우주학회지
• /
• 제46권10호
• /
• pp.833-844
• /
• 2018

본 연구에서는 무인 회전익기의 종류인 쿼드콥터의 로터 블레이드에 대해 바람 및 비행 조건의 따른 공력특성을 예측하고자 한다. 돌풍 및 비행 조건들을 고려하기 위해 바람의 좌표계 변환 개념을 제시하였다. 강체 블레이드 플래핑 운동방정식을 고려한 깃 요소 및 운동량 이론을 이용해 개별 로터의 제자리, 전진, 상승 비행을 해석하였다. XFOIL을 사용하여 공력결과를 도출하였고, 개발된 BEMT를 이용하여 제자리 비행, 전진, 상승 조건의 검증을 수행했다. 또한 제자리 비행 실험 환경 구축 및 실험 결과와 개발된 BEMT의 비교 및 검증을 수행하였다.

• 한국항공우주학회지
• /
• 제36권2호
• /
• pp.163-170
• /
• 2008

혼합 보 이론과 적정변형 보 이론에 입각한 공탄성 해석 시스템을 결합하여 유연면을 갖는 복합재료 무힌지 로터에 대한 정지 및 전진 비행시의 공탄성 해석을 수행하였다. 블레이드에 작용하는 공기력은 Leishman-Beddoes의 비정상 공력 모델을 이용하여 구했다. 인장, 회전면 내외의 굽힘, 그리고 비틀림이 상호 연계된 블레이드에 대한 운동방정식은 Hamilton의 원리에 입각하여 유도하였다. 헬리콥터 블레이드의 공탄성 해석에 주요한 요소들인 단면 벽의 두께, 탄성연계, 그리고 구성방정식에 대한 적합한 가정과 같은 주요 구조 모델링 문제들에 대한 효과들을 고찰하였다. 이러한 요소들은 블레이드 단면의 복합재료 적층 구조에 민감하게 반응하며, 블레이드 안정성에도 적지 않은 영향을 나타냄을 보였다.