• 한국농공학회지
• /
• 제30권3호
• /
• pp.106-113
• /
• 1988

This study was performed to obtain the basic data which can be applied to use of foamihg mortars. 1. At the mixing ratio 1:1, the highest strengths were showed by foaming mortam, respec - tively. But, it. gradually was decreased in poorer mixing ratio and more addition of foam- ing agent. The decreasing rates of strengths were incresed in poorer mixing ratio and more addition of foaming agent. 2. The strengths were decreased up to 77.0-92.8% by mix-foaming type and 36.7-74.4% by pre-foamed type than cement mortar. 3. At the mixing ratio of 1:1, the lowest air contents were showed by foaming mortars, respectively. But, it gradually was increased in poorer mixing ratio and more addition of foaming agent. The increasing rates of air contents were increased in richer mixing ratio and more addition of foaming agent. 4. Air contents were showed up to 26.0-63.8 times by mix-foaming type and 5.8-17.7 times by pre-foamed type than cement mortar, respectively. 5. The correlations between compressive strength and air content were highly significant, respectively. The multiple regression equations of strengths and air content were computed depending on a fuction of mixing ratio and addition of foarning agent. It was highly significant, respectively.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.132-133
• /
• 2014

In this study, high volume of industrial by-products including blast furnace slag, recycled aggregate powder and incineration ash have been utilized on the slurry of the foamed lightweight concrete. As to decrease the price of the lightweight foam concrete, mortar based slurry and concrete based slurry has been fixed. As the variation of the foam conduction ratio and aggregates, the foam ratio and compressive strength has been tested. Results showed that using recycled aggregates in the slurry showed better effect than using natural aggregates due to the alkali properties of the recycled aggregates could activate the potential hydraulic properties of the blast furnace slag. Consider about the low price of the recycled aggregates, it could be identified that using recycled aggregates in high volume blast furnace slag blended lightweight concrete showed better compressive strength than natural aggregates.

• 농업과학연구
• /
• 제15권1호
• /
• pp.82-94
• /
• 1988

이 논문(論文)은 기포(起泡)모르터의 제특성(諸特性)에 관(關)한 기초자료(基礎資料)를 제공(提供)하고져 수행(遂行)되었는 바, 이 연구(硏究)를 통(通)하여 얻어진 결과(結果)를 요약(要約)하면 다음과 같다. 1. 각(各) 기포(氣泡)모르터에서 물-시멘트비는 당배합비(富配合比)일수록, 기포제(起泡劑) 및 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 감소(減少)하였으며, 보통(普通)시멘트 모르터에 비(比)하여 혼합기포주입형(混合氣泡注入型)은 1.6~53.1%, 사전기포주입형(事前氣泡注入型)은 4.4~24.1%의 물-시멘트비(比)가 감소(減少)되었다. 2. 각(各) 기포(氣泡)모르터의 밀도(密度)는 빈배합(貧配合)일수록, 기포제(起泡劑) 및 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 작게 나타났으며, 밀도(密度)의 감소율(減少率)은 당배합(富配合)일수록, 기포제(起泡劑) 및 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 크게 나타났다. 3. 기포(起泡)모르터는 보통(普通)시멘트 모르터에 비(比)하여 혼합기포주입형(混合氣泡注入型)은 38.8~55.9%, 사전기포주입형(事前氣泡注入型)은 9.7~23.6%의 자중감소(自重減少)를 보였다. 4. 각(各) 기포(起泡)모르터의 급수율(吸水率)은 빈배합(貧配合)일수록, 기포제(起泡劑) 및 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 높게 나타났으며, 흡수율(吸水率)의 증가율(增加率)은 당배합(富配合)일수록, 기포제(起泡劑) 및 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 크게 나타났다. 5. 72시간(時間) 수침(水浸)에서 각(各) 기포(氣泡)모르터의 흡수율(吸水率)은 보통(普遇)시멘트 모르터에 비(比)하여 혼합기포주입형(混合氣泡注入型)은 3.41~5.85배(倍)로 나타났으며, 사전기포주입형(事前氣泡注入型)은 1.05~1.55배(倍)로 나타났으며, 흡수율(吸水率)의 변화율(變化率)은 모두 수침초기(水浸初期)에 높게 나타나는 경향(傾向)을 보였다. 6. 각(各) 기포(氣泡)모르터의 각(各) 강도(强度)는 빈배합(貧配合)일수록, 기포제(起泡劑) 및 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 작게 나타났으며, 각(各) 강도(强度)의 감소율(減少率)은 빈배합(貧配合)일수록, 기포제(起泡劑)나 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 크게 나타났다. 7. 기포(氣泡)모르터는 보통(普通)시멘트 모르터에 비(比)하여 재령(材齡) 28일(日)에서 혼합기포주입형(混合氣泡注入型)은 77.0~92.8%, 사전기포주입형(事前氣泡注入型)은 36.7~74.4%의 강도감소(强度減少)를 보였고, 각(各) 기포(氣泡)모르터의 각(各) 강도간(强度間)의 상관관계(相關關係)는 직선형(直線形)으로 나타났으며 고도(高度)의 유의성(有意性)이 인정(認定)되었다. 8. 각(各) 기포(氣泡)모르터의 공기량(空氣量)은 빈배합(貧配合)일수록, 기포제(起泡劑)나 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 크게 나타났으며, 공기량(空氣量)이 증가율(增加率)은 당배합(富配合)일수록, 기포제(起泡劑)나 기포(氣泡)의 첨가량(添加量)이 증가(增加)할수록 높게 나타났다. 9. 기포(氣泡)모르터의 공기량(空氣量)은 보통(普通)시멘트 모르터에 비(比)하여 혼합기포주입형(混合氣泡注入型)은 26.0~63.8배(倍), 사전기포주입형(事前氣泡注入型)은 5.8~17.7배(倍)를 보였다. 10. 각(各) 기포(氣泡)모르터에서 밀도(密度)와 흡수율(吸水率), 압축강도(壓縮强度) 및 공기량(空氣量)과의 상관관계(相關關係)는 매우 높은 유의성(有意性)을 보였고, 배합비(配合比)와 기포제(起泡劑) 및 기포(氣泡)의 첨가량(添加量)에 따라 밀도(密度), 흡수율(吸水率), 제강도(諸强度) 및 공기량(空氣量)을 추정(推定)할 수 있는 다중회귀방정식(多重回歸方程式)을 유도(誘導)하였으며 각(各) 방정식(方程式)은 고도(高度)의 유의성(有意性)이 인정(認定)되었다.

• Computers and Concrete
• /
• 제23권2호
• /
• pp.97-106
• /
• 2019

This paper describes the design of a new interlocking masonry system, the production of designed interlocking units and mechanical properties of interlocked masonry assemblages with mortar. In this proposed system, units have horizontal and vertical locks to integrate the units to the wall and have a channel to enable the use of horizontal reinforcements in the wall. Using these units, unfilled, filled or reinforced walls can be constructed with or without mortar. In the production of the interlocking units, it was decided to use foamed concrete. 12 trial productions have been carried out at different mix proportions to obtain the optimum concrete mix. At the end of the mentioned productions, the units were produced with foam concrete which is selected as the most suitable in terms of compressive strength and specific gravity. Then, axial compression, diagonal tension and bed joint shear tests were carried out to determine the mechanical properties of the interlocked masonry assemblages with mortar. Results from the tests showed that interlocks designed to strengthen the system against shear stresses by creating discontinuity throughout the joints have been successful to achieve their aim. Obtained data will enable structural analysis of walls to be constructed with these new units.

• 한국지반공학회논문집
• /
• 제27권12호
• /
• pp.53-68
• /
• 2011

본 연구에서는 기존 NATM 터널공법의 문제점을 개선한 신개념의 NATM Composite 라이닝 공법 개발에 대한 기초 연구를 수행하였다. 먼저 NATM Composite 라이닝 공법의 개요 대하여 소개하고 시공성에 대한 검토를 수행하였다. 그리고 NATM Composite 라이닝 공법의 개발을 위한 기초 연구로서 고성능 PC 패널 라이닝의 개발을 위해 다양한 혼화재료의 영향을 검토하고, PC 패널 설치 위치별 최적 배합을 도출하였다. 또한 PC 패널 배면 뒤채움재로 경량기포 모르타르 재료를 개발하였으며 실대형 하중재하 실험을 통해 NATM Composite 라이닝 공법의 거동 특성을 규명하였다. NATM Composite 라이닝 공법은 기존 현장타설 라이닝 공법에 비해 안정성과 시공성을 크게 향상 시킬 수 있을 것으로 판단된다.

• 기술사
• /
• 제17권3호
• /
• pp.22-31
• /
• 1984

Sardine ant mackerel so called dark muscled fish have been underutilized due to the disadvantages in bloody meat color, high content of fat, and postmortem instability of protein. Recent efforts were made to overcome these defects and develope new types of product such as texturized protein concentrates and dark muscle eliminated minced fish. Approach of this study is based on the rapicl dehydration of foamed fish-starch paste by dielectric heating. In process comminuted sardine meat was washed more than three times by soaking and decanting in chilled water and finally centrifuged. The meat was ground in a stone mortar added with adequate amounts of salt, foaming agent, and other ingredients for aid to elasticity and foam stability. The ground meat paste was extruded in finger shape and heated in a microwave oven to give foamed, expanded, and porous solid structure by dehydration. Dielectric constant ($\varepsilon$′) and dielectric loss ($\varepsilon$") vcalues of sardine meat paste were influenced by wavelength and moisture level. Those values at 100KHz and 15MHz were ranged 2.25∼9.86 ; 2.22∼4.18 for $\varepsilon$′ and 0.24∼19.24 ; 0.16∼1.25 for $\varepsilon$", respectively, at the moisture levels of 4.2∼13.8％. For a formula for fish-starch paste preparation, addition of 20∼30% starch (potato starch) to the weight of fish meat, 2∼4% salt, and 5∼10% soybean protein was adequate to yield 4∼5 folds of expansion in volume when heated. Addition of egg yolk was of benefit to micronize foam size and better crispness. In order to provide better foaming and dehydration, addition of 0.2∼0.5% sodium bicarbonate foaming agent, was proper to result in foam size of 0.5∼0.7mm and foam density of 200∼400/$\textrm{cm}^2$ which gave a good crispness.

• 한국농공학회지
• /
• 제27권1호
• /
• pp.46-61
• /
• 1985

This study was performed to obtain the basic data which can be applied to the use of foaming mortars. The data was based on the properties of foaming mortars depending upon various mixing ratios and addings to compare those of cement mortar. The foaming agents which was used at this experiment were pre-foamed type and mix-foaming type which is being used as mortar structures. The foaming mortar, mixing ratios of cement to fine aggregate were 1:1, 1: 2, 1 : 3 and 1 : 4. The addings of foaming agents were 0.0%, 0.5%, 1.0%, 1.5%, 2.0%, 2.5% and 3.0% of cement weight. The results obtained were summarized as follows; 1. At the mixing ratio of 1 : 1, the lowest water-cement ratios were showed by foaming mortars, respectively. But it gradually was increased in poorer mixing ratio and decreased in more addition of foaming agent. The water-cement ratios were decreased up to 1. 8~22. 0% by G, 2. 2~24. 1 % by U and 0. 7~53. 1% by J foaming mortar than cement mortar. 2, At the mixing ratio of 1 : 1, the highest bulk densities were showed by foaming mortars, respectively. But, it gradually was decreased in poorer mixing ratio and more addition of foaming agent. The bulk densities were decreased up to 1. 4~20. 7% by G, 2. 3~23. 7% by U and 26. 5~56. 5% by J foaming mortar than cement mortar. Therefore, foaming mortar could be utilized to the constructions which need low strengths. 3. At the mixing ratio of 1:1, the lowest absorption rates were showed by foaming mortars, respectively. But, it gradually was increased in poorer mixing ratio and more addition of foaming agent. Specially, according to the absorption rate when immersed in 72 hours, the absorption rates were showed up to 1. 01~1. 24 times by G, 1. 03~1. 58 times by U and 1. 10~5. 91 times by J foaming mortar than cement mortar. It was significantly higher at the early stage of immersed time than cement mortar. 4. At the mixing ratio of 1:1, the lowest air contents were showed by foaming mortars, respectively. But, it gradually was increased in poorer mixing ratio and more addition of foaming agent. Air contents were contented up to 4. 0~17. 2 times by G, 5. 2~23. 2 times by U and 23. 8~74. 5 times by J foaming mortar than cement mortar. 5. At the mixing ratio of 1 : 1, the lowest decreasing rates of strengths were showed by foaming mortars, respectively. But, it gradually was increased in poorer mixing ratio and more addition of foaming agent. Specially, the strengths of 28 days were decreased 0. 4~2. 2% than those of 7 days by foaming mortar, respectively. Also, the correlations between compressive and tensile strength, compressive and ending strength, tensile and bending strength were highly significant as a straight line shaped, respectively. 6. The correlations between absorption rate, air content, compressive strength and bulk density, absorption rate, compressive strength and air content were highly significant, respectively. The multiple regression equations of water-cement ratio, bulk density, absorption ate, air content, compressive strength, tensile strength and bending strength were computed depending on a function of mixing ratio and addition of foaming agent. It was highly significant, respectively. 7. At the mixing ratio of 1 : 1, the highest strengths were showed by cement mortar and foaming mortars, by chemical reagents. But, it gradually was decreased in poorer mixing ratio. The decreasing rates of strengths were in order of H $_2$S0 $_4$, HNO$_3$ and HCI, J,U,G foaming mortar and cement mortar. Specially, at the each mixing ratio, each chemical reagent and 3.0% of foaming agent, J foaming mortar was collapsed obviously. Therefore, for the structures requiring acid resistence, adding of foaming agent should be lower than 3.0%.

• KIEAE Journal
• /
• 제10권3호
• /
• pp.89-96
• /
• 2010

In comparison with ordinary or heavy-weight concrete, light-weight air void concrete has the good aspects in optimizing super tall structure systems for the process of design considering wind load and seismic load by lightening total dead load of buildings and reducing natural resources used. Light-weight air void concrete has excellent properties of heat and sound insulating due to its high amount porosity of air voids. So, it has been used as partition walls and the floor of Ondol which is the traditional Korean floor heating system. Under the condition of which the supply of light-weight aggregates are limited, the development of light-weight concrete using air voids is highly required in the aspects of reduced manufacturing prices and mass production. In this study, we investigated the physical properties and thermal behaviors of specimens that applied different mixing ratios of foaming agent to evaluate the possibility of use in the structural elements. We proposed the estimating equation for compressive strength of each mix having different ratio of foaming agent. We also confirmed that the density of cement matrix is decreased as the mixing amount of foaming agent increase up to 0.6% of foaming agent mixing ratio which was observed by SEM. Based on porosity and compressive strength of control mortar without foaming agent, we built the estimating equations of compressive strength for mortars with foaming agent. The upper limit of use in foaming agent is about 0.6% of the binder amount. Each air void is independent, and size of voids range from 50 to $100{\mu}m$.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2008년도 추계 학술발표회
• /
• pp.1555-1558
• /
• 2008

In this paper, result of whole test, When the Transfer Distance is increasing, Strength of Backfilling Material of NATM Composite lining Tunnel due to increasing Gravity was increased, but that is higher the Air Flotation than increasing Strength. So, That was predicted a drop of Permeability. And Performing the placing Lightweight Foamed Mortar, we think that it's performance in drain material was lost. Therefore We conclude that Proper Transfer Distance that taking Permeability through minimizing of Air Flotation Loss and getting the Need Strength is 50m.

• 한국건설순환자원학회논문집
• /
• 제7권1호
• /
• pp.37-43
• /
• 2019

본 연구에서는 각종 산업부산물(플라이애시 2종, 페트로 코크스 연소 유동층 보일러 애시 및 고로 슬래그 미분말)을 활용한 싱크홀 복구용 경량 충전재 제조에 관한 연구를 수행하였다. 이를 위해 혼합물 실험계획법을 적용하여 산업부산물의 배합비에 따른 혼합 원료 물성(압축강도) 거동을 검토하였고, 상용프로그램인 MINITAB을 사용하여 통계적 분석을 하였다. 산업부산물의 배합조건별 압축강도는 고로 슬래그 미분말에 강한 의존성을 나타냈으며, 압축강도(3일 재령)는 고로 슬래그 미분말 사용량에 3~11MPa 수준이며, 유동층 보일러 플라이애시의 사용은 압축강도 발현에 미치는 영향이 가장 적은 것으로 평가되었다. 그리고 혼합물 실험계획에 따른 원료 배치 1조건에 대해서 기포 콘크리트를 제조하여 압축강도와 투수계수를 측정하였으며, 이때 부피비중 0.9~1.0, 겉보기 기공률은 30~50% 수준, 압축강도(3일 재령)는 1~2MPa 수준, 투수계수는 $10^{-2}{\sim}10^{-3}cm/sec$ 수준이다.