• Journal of Powder Materials
• /
• v.27 no.2
• /
• pp.132-138
• /
• 2020

A facile one-pot wet chemical process to prepare pure anatase TiO₂ hollow structures using ammonium hexafluorotitanate as a precursor is developed. By defining the formic acid ratio, we fabricate TiO₂ hollow structures containing fluorine on the surface. The TiO₂ hollow sphere is composed of an anatase phase containing fluorine by various analytical techniques. A possible formation mechanism for the obtained hollow samples by self-transformation and Ostwald ripening is proposed. The TiO₂ hollow structures containing fluorine exhibits 1.2 - 2.7 times higher performance than their counterparts in photocatalytic activity. The enhanced photocatalytic activity of the TiO₂ hollow structures is attributed to the combined effects of high crystallinity, specific surface area (62 ㎡g^-1), and the advantage of surface fluorine ions (at 8%) having strong electron-withdrawing ability of the surface ≡ Ti-F groups reduces the recombination of photogenerated electrons and holes.

• Journal of the Korean Chemical Society
• /
• v.62 no.1
• /
• pp.7-13
• /
• 2018

The potential of zinc fluorides with different molar ratios of Zn/F was applied as a solid catalyst in the simultaneous reaction of transesterification and esterification of crude palm oil (CPO) for biodiesel production. These materials were prepared by the fluorolytic sol-gel technique with different fluorine contents. The resulting samples were investigated using elemental analysis, XRD, FT-IR, TG/DTG, $N_2$ physisorption measurements and SEM. The results exhibited that the presence of fluorine strongly affected the catalytic activity in the biodiesel production. The catalysts with smaller fluorine contents (${\leq}1$) showed the best performance in all of the observed samples, yields from 92.94 to 89.95, 87.38 and 85.21% with increasing fluorine contents, respectively. The yield toward the formation of biodiesel depended on the phase and particle sizes of catalysts, but it was not influenced by surface area, pore size, and volume of the samples. The recovered catalyst showed a gradual decrease in activity over three cycles of same reactions.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2006.05a
• /
• pp.109-112
• /
• 2006

A fluorine-doped diamond-like carbon (F-DLC) stamp which has high contact angle, high UV-transmittance and sufficient hardness, was fabricated using the following direct etching method: F-DLC is deposited on a quartz substrate using DC and RF magnetron sputtering, PMMA is spin coated and patterned using e-beam lithography and finally, $O_2$ plasma etching is performed to transfer the line patterns having 100 nm line width, 100 nm line space and 70 nm line depth on F-DLC. The optimum fluorine concentration was determined after performing several pre-experiments. The stamp was applied successfully to UV-NIL without being coated with an anti-adhesion layer.

• Nuclear Medicine and Molecular Imaging
• /
• v.43 no.1
• /
• pp.1-9
• /
• 2009

As many new drug substances contained various aromatic rings and fluorine attached to an electron rich aromatic ring or on the meta-position, a strategy towards improvement in aromatic fluorination of these compounds is highly desirable. The introduction of fluorine-18 onto aromatic rings showed in the limited condition containing electron withdrawing group (EWG) on the para- or ortho-position to get reasonable radiochemical yield so far. No-carrier added (NCA) [$^{18}F$]fluoroarene syntheses by iodonium salts recently reported that has the potential to greatly increase the yield in systems or positions that normally not reactive enough to give sufficient yields in simple model reaction. This review describes the methodological approach towards effective aromatic fluorination by diaryliodonium salts and future prospects in an application of novel PET radiotracer.

• Elastomers and Composites
• /
• v.50 no.1
• /
• pp.55-61
• /
• 2015

Manufacturing process of OLED contains adsorption-desorption process of glass substrate. There are several adsorption methods of glass substrate such as atmospheric pressure, vacuum and electrostatic adsorption. However, these methods are very complex to connect system. Therefore, the adsorption method using silicone rubber based sticking chuck was proposed in this study. Three types of silicone rubbers having 0, 19.3 and 32.2 wt% of fluorine were used and their mechanical properties, surface energies and adsorption properties were examined. According to the results ${\sigma}_{300}$ and hardness increased with increasing fluorine contents, but elongation was decreased. Also, fluorosilicone rubber containing 32.2 wt% of fluorine showed the lowest surface tension, among three types of rubber and resulted in the highest initial tack with glass substrate. After the adsorption-desorption test of 300,000 cycles was performed, the adsorption force of S-1 (silicone rubber) decreased largely from 2.34 to 0.73 MPa. However, the S-3 (fluorosilicone rubber having 32.2 wt%. of fluorine) decreased only from 3.15 to 2.24 MPa. From this study, we obtained the valuable equations related to long term durability of silicone based sticking chuck. Finally the transfer of silicone rubber to glass substrate with the adsorption-desorption process was not occurred and this phenomenon was examined by UV-Visible spectroscopy.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.145-146
• /
• 2006

A fluorine-doped diamond-like carbon (F-DLC) stamp which has high contact angle, high UV-transmittance and sufficient hardness, was fabricated using the following direct etching method: F-DLC is deposited on a quartz substrate using DC and RF magnetron sputtering, PMMA is spin coated and patterned using e-beam lithography and finally, O2 plasma etching is performed to transfer the line patterns having 100 nm line width, 100 nm line space and 70 nm line depth on F-DLC. The optimum fluorine concentration was determined after performing several pre-experiments. The stamp was applied successfully to UV-NIL without being coated with an anti-adhesion layer.

• Progress in Superconductivity
• /
• v.7 no.2
• /
• pp.152-157
• /
• 2006

New precursor solution with dichloroacetic acid (DCA) was developed for fabricating high $J_c$ REBCO film. DCA based-precursor solution was coated on $LaAlO_3$(001) substrate by dip coating method. Processing parameters such as oxygen partial pressure, water vapor, ramping rate and pyrolysis temperature were controlled in order to obtain a good epitaxial film. The film with thickness of 0.5 micrometer was obtained by single coating and no crack was observed at calcined films. Oxygen partial pressure was controlled in the range of $100{\sim}1,000$ ppm and conversion heat treatment was carried out at the temperature range of $705-765^{\circ}C$. A critical transition temperature ($T_c$) of 90 K and a critical transport current density ($J_c$) of $>0.5\;MA/cm^2$ (77 K and self-field) were obtained for the GdBCO film. It is thought that fluorine-free MOD solution using DCA is promising precursor solution for fabricating high quality REBCO films.

• The Journal of the Korean dental association
• /
• v.48 no.6
• /
• pp.454-458
• /
• 2010

Dental caries is one of the most common chronic diseases in the world, which are caused by complex actions of oral such factors as the bacteria, food, tooth, saliva and other factors. Although this is one of the typical oral diseases, we can acquire a high prophylactic effect by use of proper prophylactic measures and management. At the beginning of the 1940s, fluorine was first introduced to prevent dental caries which now is widely used. The fluorine application effects are varied from different concentrations and categories of fluorine, and different application method and frequency, etc. There is great debate on the best application method at the present. Dental clinics use iontophoresis as the application method and use it clinically. It uses APF (1.23%, Acidulated phosphate fluoride, APF) and uses 2% NaF so as to encourage more absorption of fluorine. Recently, fluoride varnish, which uses admixture mucus of colophony resin into 5% NaF, and a variety of forms that can be applied in the oral cavity are still being continuously researched. When using fluoride topical application on the enamel surface, it was highly recommended that fluoride varnish be used directly after fluoride iontophoresis rather than fluoride iontophoresis only or fluoride varnish by itself. The new method is more effective and does not need repeated application.

• Macromolecular Research
• /
• v.17 no.11
• /
• pp.870-873
• /
• 2009

In this study, 2-diglycidylether of benzotrifluoride (2-DGEBTF) and 4-diglycidylether of benzotrifluoride (4-DGEBTF) epoxy resins, which contained fluorine groups in the main chain, were synthesized. The resins were characterized by FTIR, $^1H$ NMR, $^{13}C$ NMR and $^{19}F$ NMR spectroscopy. The 2-DGEBTF and 4-DGEBTF epoxy resins were cured with triethylene tetramine (TETA), and the effect of the fluorine group on the synthesized epoxy resin on the cure behavior, thermal, and mechanical properties was investigated. The 2-DGEBTF/TETA system was more reactive than the 4-DGEBTF/TETA system, whereas the thermal stability factor i.e., the decomposition activation energy ($E_d$), of 4-DGEBTF/TETA was higher than that of 2-DGEBTF/TETA. These results can be explained by the decrease in cross-linking density and decomposition of the short side chains, resulting in the $CF_3$ group at the para position. However, the $K_{IC}$ value of 4-DGEBTF/TETA was higher than that of 2-DGEBTF/TETA. This was attributed to the increase in flexibility in the epoxy backbone, resulting in a difference in steric hindrance and polarlizability.

• Nuclear Engineering and Technology
• /
• v.55 no.4
• /
• pp.1324-1331
• /
• 2023

In the present work, we carried out a molecular dynamics study of the kinetic properties of the FLiNaK molten salt, as well as a detailed study of the structure of this salt melt. The high value of the self-diffusion coefficient of fluorine ions is due to the large number of Coulomb repulsions between the most numerous negative ions. The calculated values of shear viscosity are in good agreement with the experimental data, as well as with the reference data obtained on the basis of finding the most reliable data. The total and partial functions of the radial distribution are calculated. According to the statistical analysis, fluorine ions have the greatest numerical diversity in the environment of similar ions, and sodium ions with the lowest representation in FLiNaK, have the least such diversity. For the subsystem of fluorine ions, the rotational symmetry of the fifth order is the most pronounced. Some of the fluorine ions form linear chains consisting of three atoms, which are not formed for positive ions. The results of the work give an understanding of the behavior molten FLiNaK under operating conditions in a molten salt reactor and will find application in future studies of this molten salt.