• Resources Recycling
• /
• v.19 no.2
• /
• pp.45-53
• /
• 2010

During the biomass gasification, tar generation is typically accompanied, which causes many problems, such as pipe plugging and equipment fouling. In the experiments, activated carbon was applied to the upper reactor of the two-stage gasifier in order to remove the tar generated during gasification. In addition, the effects of the upper-reactor temperature and equivalence ratio on the producer gas characteristics (composition, tar content and lower heating value) were investigated. To investigate the effect of the upper reactor-temperature, experiments were performed at 743, 793, $838^{\circ}C$, respectively. To examine the influence of the equivalence ratio, a comparison experiment was carried out at a equivalence ratio of 0.17. In all experiments, tar contents in the producer gases were below $2mg/Nm^3$. The maximum LHV of the producer gas was above $10MJ/Nm^3$, which is much higher than the typical LHV($3\sim6MJ/Nm^3$) in the air gasification of biomass.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.111-114
• /
• 2010

In the attrition reactor for the American Society for Testing and Materials (ASTM) D5757-95, the attrition characteristics of catalysts for water gas shift reaction were investigated. The effects of attrition characteristics of low temperature shift catalysts (LTS) and high temperature shift catalysts (HTS) on fluidization phenomena and average particle size were investigated and compared with the attrition characteristics of sand particles. The particle size of catalysts was decreased and particle size distribution in attrition tube was changed due to the effect of gas injection. About 40~50 wt% samples of original catalyst particles were entrained and lost. The amount of fly ash of LTS catalyst was less than that of HTS. Also, the weight of entrained particles which had original particle size of $212{\sim}300{\mu}m$ was lower than any other cases.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.590-597
• /
• 2010

HTGR using a TRISO coated particles as nuclear raw fuel material can be used to produce clean hydrogen gas and process heat for a next-generation energy source. For these purposes, a TRISO coated particle was prepared with 3 pyro-carbon (buffer, IPyC, and OPyC) layers and 1 silicone carbide (SiC) layer using a CVD technique on a spherical $UO_2$ kernel surface as a fissile material. In this study, a spherical $UO_2$ particle was prepared using a modified sol-gel method with a vibrating nozzle system, and TRISO coating fabrication was carried out using a fluidized bed reactor with coating gases, such as acetylene, propylene, and methyltrichlorosilane (MTS). As the results of this study, a spherical $UO_2$ kernel with a sphericity of 1+0.06 was obtained, and the main process parameters in the $UO_2$ kernel preparation were the well-formed nature of the spherical ADU liquid droplets and the suitable temperature control in the thermal treatment of intermediate compounds in the ADU, $UO_3$, and $UO_2$ conversions. Also, the important parameters for the TRISO coating procedure were the coating temperature and feed rate of the feeding gas in the PyC layer coating, the coating temperature, and the volume fraction of the reactant and inert gases in the SiC deposition.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.1
• /
• pp.86-94
• /
• 2011

Pyrolytic lignin was obtained from biooil produced with yellow poplar wood. Fast pyrolysis was performed under various temperature ranges and residence times using fluidized bed type reactor. Several analytical methods were adopted to characterize the structure of pyrolytic lignin as well as the effect of pyrolysis temperature and residence time on the modification of the lignin. The yield of pyrolytic lignin increased as increasing pyrolysis temperature and decreasing residence time of pyrolysis products. The molecular weight of pyrolytic lignin determined by gel permeation chromatography (GPC) was approximately 1,200 mol/g, which was approximately a tenth of milled wood lignin (MWL) purified from the same woody biomass. Based on analytical data, demethoxylation and side chain cleavage reaction were dominantly occurred during fast pyrolysis.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.4
• /
• pp.412-420
• /
• 2016

Effect of $H_2S$ on reactivity of oxygen carrier was measured and discussed using fluidized bed reactor and SDN70 oxygen carrier. We could get 100% of fuel conversion and $CO_2$ selectivity even though $H_2S$ containing simulated syngas was used as fuel for reduction. Absorbed sulfur was released during oxidation and $N_2$ purge step after oxidation as $SO_2$ form. We could get 100% of fuel conversion and $CO_2$ selectivity during cyclic reduction-oxidation tests up to 10th cycle. However, only 6~7% of sulfur can be removed during oxidation and $N_2$ purge step and 93~94% of sulfur was accumulated in the oxygen carrier. Therefore we could conclude that total removal of sulfur was not possible. $SO_2$ emission during oxidation decreased as the number of cycle increased. Therefore we could expect that the reactivity of oxygen carrier will be decreased with time.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.107.2-107.2
• /
• 2011

억새는 척박한 토양 조건에서도 쉽게 자라며 관리가 용이하다는 장점이 있어 바이오에너지 작물로 주목을 받고 있다. 억새는 주로 Miscanthus sacchariflorus(물억새)와 Miscanthus sinensis(참억새) 그리고 두 억새의 잡종인 Miscanthus giganteus로 구분되며, 최근 기존의 억새보다 생체량을 크게 늘린 거대억새가 개발되기도 하였다. 본 실험에서는 우리나라 전역에서 가장 흔하게 볼 수 있는 물억새와 참억새를 유동층 반응기를 이용하여 급속열분해 하였다. 본 연구의 목적은 억새로부터 얻은 바이오원유와 나무로부터 얻은 바이오원유의 특성을 비교하고, 시료투입속도의 변화를 주어 억새로부터 얻은 바이오원유의 수율과 특성을 알아보고자 함이다. 시료의 투입속도는 200g/h, 300g/h, 500g/h, 1000g/h로 변화를 주었으며, 반응온도($500^{\circ}C$), 공탑속도(0.19m/s), 응축기온도($10^{\circ}C$)는 매 실험마다 동일하게 유지하였다. 수집한 바이오원유는 공업분석을 통해 연료로서의 가치를 알아보았다. 목재를 급속열분해 한 경우 바이오원유의 수율은 56.03wt.%로 동일한 조건에서 억새를 급속열분해 한 경우 보다 약 6wt.%가량 높았다. 바이오원유의 발열량은 큰 차이가 없었으나 수분과 점도에서 큰 차이를 보였다. 투입속도가 증가할수록 바이오원유의 수율은 증가하는 경향을 보였으며, 시간당 1000g을 투입하였을 때는 수율이 감소하였으나 수율의 변화는 크지 않았다. 투입속도가 증가하는 경우 바이오원유의 고위발열량과 점도는 감소하고 수분이 증가하는 경향을 보였다.

• Journal of Energy Engineering
• /
• v.26 no.3
• /
• pp.97-104
• /
• 2017

In this study, waste tire rubbers were pyrolyzed in a lab-scale pyrolysis plant equipped with a fluidized bed reactor in a temperature ranges of $450-650^{\circ}C$. The main object of this work is to investigate the properties of pyrolysis oil with reaction temperatures and the behavior of sulfur in the products when waste polypropylene was added for co-pyrolysis. The maximum yield of oil was about 52wt.% at the reaction temperature of $456^{\circ}C$. From GC-MS analysis, the pyrolysis oils consisted mainly of limonene, toluene, xylene, styrene, trimethylbenzene, methylnaphthalenes and some heteroatom(sulfur and nitrogen)-containing compounds. The addition of waste polypropylene resulted in decrease in sulfur contents of the pyrolysis oils.

• Transactions of the Korean hydrogen and new energy society
• /
• v.25 no.1
• /
• pp.87-96
• /
• 2014

Direct combustion characteristics of coal and oxygen carrier were measured in the thermogravimetric analyzer using four coals and two different oxygen carriers. The direct combustion efficiency decreased in order of Roto, Kideco, Sunhwa and Hyper coal for both oxygen carriers. Moreover, OCN703-1100 oxygen carrier showed better combustion efficiency than OCN706-1100 oxygen carrier for all four coals. The reduction characteristics of two oxygen carriers for $CH_4$, CO and $H_2$ gases were measured in the thermogravimetric analyzer to investigate why OCN703-1100 oxygen carrier showed better combustion efficiency than OCN706-1100 for all coals. The OCN703-1100 oxygen carrier represented higher reduction rate than OCN706-1100 for all reducing gases. Moreover, the total pore area and the porosity of OCN703-1100 were higher than those of OCN706-1100 oxygen carrier. The total volatile gas and volatile components of four coals were measured in a batch type fluidized bed reactor to investigate why the direct combustion efficiency decreased in order of Roto, Kideco, Sunhwa and Hyper coal for both oxygen carriers. The direct combustion efficiency was proportional to the total amount of ($CH_4+CO+H_2$) produced during devolatilization of coals.

• Korean Chemical Engineering Research
• /
• v.54 no.4
• /
• pp.533-542
• /
• 2016

We investigate fluidization characteristics of the mixture of rice husk, silica sand and rice husk ash as a preliminary study for valuable utilization of rice husk ash obtained from gasification of rice husk in a fluidized bed reactor. As experiment valuables, the blending ratio of rice husk and sand (rice husk: sand) is selected as 5:95, 10:90, 20:80 and 30:70 on a volume base. Rice husk ash was added with 6 vol% of rice husk for each experiment and air velocity to the reactor was 0~0.63 m/s. In both rice husk/sand and rice husk/sand/ash mixture, the minimum fluidization velocity (Umf) is observed as 0.19~0.21 m/s at feeding of 0~10 vol.% of rice husk and 0.30 m/s at feeding of 20 vol.% of rice husk. With increasing the amount of rice husk up to 30 vol.%, $U_{mf}$ can not measure due to segregation behavior. The mixing index for each experiment is determined using mixing index equation proposed by Brereton and Grace. The mixing index of the mixture of rice husk/sand and rice husk/sand/ash was 0.8~1 and 0.88~1, respectively. The optimum fluidization condition was found for the good mixing and separation of rice husk ash.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.7 no.3
• /
• pp.175-182
• /
• 2009

The spent cationic exchange resins and anionic exchange resins were separated from mixed spent exchange resins by a fluidized bed gravimetric separator. The separated resins were identified by an elemental analysis and thermogravimetric analysis. The each test sample was prepared by diluting the slurry made by wet ball milling the cationic exchange resins and the anionic exchange resins separated as a spherical granular form for 24 hours. The resulting test samples showed a slurry form of less than $75{\mu}m$ of particle size and 25,000ppm of $COD_{cr}$. The decomposition conditions of each test samples from a thermal power plant were obtained with a lab-scale(reactor volume : 220mL) supercritical water oxidation(SCWO) facility. Then pilot plant(reactor volume : 24 L) tests were performed with the test samples from a thermal power plant and a nuclear power plant successively. Based on the optimal decomposition conditions and the operation experiences by lab-scale facility and the pilot plant, a commercial plant(capacity : 150kg/h) can be installed in a nuclear power plant was designed.