• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.10a
• /
• pp.358-363
• /
• 1995

A study on passive cooling systems for concrete containment of advanced pressurized water reactors has been performed. The proposed passive containment cooling system (PCCS) consist of (1) condenser units located inside containment, (2) a steam condensing pool outside containment at higher elevation, and (3) downcommer/riser piping systems which provide coolant flow paths. During an accident causing high containment pressure and temperature, the steam/air mixture in containment is condensed on the outer surface of condenser tubes transferring the heat to coolant flowing inside tubes. The coolant transfers the heat to the steam condensing pool via natural circulation due to density difference. This PCCS has the following characteristic: (1) applicable to concrete containment system, (2) no limitation in plant capacity expansion, (3) efficient steam condensing mechanism (dropwise or film condensation at the surface of condenser tube), and (4) utilization of a fully passive mechanism. A preliminary conceptual design work has been done based on steady-state assumptions to determine important design parameter including the elevation of components and required heat transfer area of the condenser tube. Assuming a decay power level of 2%, the required heat transfer area for 1,000MWe plant is assessed to be about 2,000 ㎡ (equivalent to 1,600 of 10 m-long, 4-cm-OD tubes) with the relative elevation difference of 38 m between the condenser and steam condensing pool and the riser diameter of 0.62 m.

• Journal of environmental and Sanitary engineering
• /
• v.10 no.2
• /
• pp.79-88
• /
• 1995

The electrostatic precipitation of Auto- Bias has the advantages of a little of power consumption by the voltage to apply only at ionizer and the prevention of fire danger by current flow over. As this ionizer wire was used WXN- Pt material of diameter 90$\mu $m, that improved ion efficiency and safety, simplified a existing source of electric power by induced Auto- Bias voltage. Also, the new type collector used electric conductivity- film wag superior a electric safety and dust collection efficiency and was possible to wash it by water. As a experiment result of this Auto- Bias electrostatic collector, the induced Auto- Bias voltage by appling D.C 4.0∼6.0kV at ionizer was 1.3∼2.3kV and then the power consumption by applied voltage was 8- l8W. The pressure loss of collector by the amount of flowing was 6.1 OmmH$_{2}$O in 300m$^{3}$/hr and showed a safe state of the dust collection. The collection efficiency by particle size was 65.1-95.8% in 0.5∼5.0$\mu $m. After corona discharge of ionizer, the remains ozone concentration was found much lower than that of ACGIH or air pollution criteria in Korea.

• Journal of Adhesion and Interface
• /
• v.10 no.4
• /
• pp.174-181
• /
• 2009

The viscosity for hi-solid pressure sensitive adhesive to improve water soluble low viscosity pressure sensitive adhesive polymerized using seeded polymerization. While seed binder polymerizing it produces an optimum polymerization condition, and acrylic acid and seed binder concentration changed were measurement of viscosity variation and adhesive power at the substrate (SUS420J) as flowing results. In adhesive polymerization, seed binder concentration 7 wt%/monomer was recovered 60% of solid content, 2,100 cps of low viscosity and clear adhesive film. When acrylic acid content was 4 wt%/monomer, it was turned excellent adhesive power and holding power.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.8 no.1
• /
• pp.140-150
• /
• 1996

CFC-12, which has been used most widely in automobile air conditioners and household refrigerators is scheduled to be phased out soon because of its high ozone depletion potential. Now HFC-134a is suggested as an alternative refrigerant for CFC-12. In this Study, we intended to investigate how PAG oil influence evaporation heat transfer and flow pattern, using R-134a and PAG oil influences evaporation heat transfer and flow pattern, using R-134a and PAG oil in the horizontal miro-fin evaporation tube. Experiments were conducted under the flowing est conditions : mass velocity 86-250kg/$m^2$s, heat flux 5-30 ㎾/$m^2$, oil concentration 0-21 wt.% and saturation temperature 5$^{\circ}C$. Local evaporation heat transfer coefficients were found to be higher at the top, side and bottom of the tube in this order. Average heat transfer coefficients turned out to increase with oil concentration increment up to 3 wt.% oil concentration, whereas heat transfer coefficients gradually decreased over 3 wt.% oil concentration, because of oil-rich liquid film was formed on the heat transfer surface. Flow patterns were rapidly transitioned to annular regimes up to 3 wt.% oil concentration. In case of pure refrigerant, measured heat transfer coefficients in the experiments were similar to those of Kandlikar＇s correlation.

• Journal of the Korean Ceramic Society
• /
• v.20 no.4
• /
• pp.305-314
• /
• 1983

In order to enhance the rate of th nitridation and to give the high density of reaction-bonded silicon nitride MgO powder as nitriding aid were added to silicon powders and the mixture was pressed isostatically into compacts which were nitrided in the furnace of 1, 35$0^{\circ}C$ where 95% $N_2$-5% $H_2$ gases were flowing. As the other nitriding aid $Mg(NO_3)_2 6H_2O$ was selected, A slip made of magnesium nitrate solution and fine silicon particles was spray-dried and then decomposed at 30$0^{\circ}C$. Magnesium oxide-coated silicon powders were formed into compacts prior to the nitridation on the same condition as the former. Magnesium nitrate (MgO, produced from the decomposition of magnesium nitrate) was more effective for the formation of the $\beta$-phase in the initial stage of the nitridation probably due to the easy formation of $MgO-SiO_2$-metal oxide eutectic melt. It has been confirmed that forsterite was formed as a result of the reaction between MgO and $SiO_2$ film of silicon surface. It was considered that MgO produced from magnesium nitrate may be finer more reactive and more uniformly distributed on the surface of silicon particles than original MgO. The higher the forming pressure was the more the $\beta$-phase was formed.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2007-2010
• /
• 2008

Vanadium pentoxide ($V_2O_5$) powder was prepared and mixed with Molybdenum Oxides ($MoM_3$) to form Mo-doped and -undoped $VO_2$ films by a sol-gel method on graphite conductive substrates. X-Ray diffraction (XRD) and scanning electron microscopy (SEM) was used to investigate the chemical compositions and microstructures of the Mo-doped and -undoped $VO_2$ films. The variation of electrical resistance was measured as a function of temperature and stoichiometric composition between vanadium and molybdenum. In this study, it was found that Mo-doped and -undoped $VO_2$ shows the typical negative temperature coefficient (NTC) behavior. As the amount of the molybdenum increases, the electrical resistance of Modoped $VO_2$ film gets reduced under the transition temperature and a linear decrease in the transition temperature is observed. From these experimental results, we can conclude that the electrical resistance behavior with temperature change of $VO_2$ films can be utilized as a self-heating source with the electrical current flowing through the graphite substrate.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.782-787
• /
• 2004

Superconducting flux flow transistor (SFFT) is based on a control of the Abrikosov vortex flowing along a channel. The induced voltage by moving of the Abrikosov vortex in an SFFT is greatly affected by the thickness, the width, and the length of channel. In order to fabricate a reproducible channel in the SFFT, we studied the variation of the critical characteristics of ${YBa}_2{Cu}_3{O}_7-\delta(YBCO)$ thin films with the etching time using ICP (Inductively coupled plasma) system. From the simulation, it was certified that the vortex velocity was increased in a low pinning energy at channel width 0,5 mm. The surfaces of YBCO thin film were etched by ICP etching system. We observed the etched channel surfaces by AFM (Atomic Force Microscope) and measured the critical current density with etching time. As a measured results, the etching thickness of channel should be optimized to fabricated a flux flow transistor with specified characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.259-262
• /
• 2003

Superconducting flux flow transistor(SFFT) is based on a control of the Abrikosov vortex flowing along a channel. The induced voltage by moving of the Abrikosov vortex in SFFT is greatly affected by the thickness and width, of channel. In order to fabricate a reproducibility channel in SFFT, we have researched the variation of the critical characteristics of YBCO thin films with the etching time using ICP(Inductively coupled plasma) system. It was certified that the velocity of vortex decreased with increasing the width of channel and was saturated faster in low bias from a simulation. An etching mechanism of YBCO thin films by ICP system was also certified by AFM(Atomic Force Microscope) and by measuring the critical current density with etching time. As measurement result, we could analyze that we should optimize the etching thickness of channel part to construct a flux flow transistor with desired characteristics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.384-385
• /
• 2005

Monolayers of lipids on a water surface have attracted much interest as models of biological membranes, but also as precursors of multilayer systems promising many technical applications. Until now, many methodologies have been developed in order to gain a better understanding of the relationship between the structure and function of the monolayers. Maxwell displacement current (MDC) measurement has been employed to study the dielectric property of Langmuir-films. MDC flowing across monolayers is analyzed using a rod-like molecular model. It is revealed that the dielectric relaxation time $\tau$ of mono layers in the isotropic polar orientational phase is determined using a liner relationship between the monolayer compression speed a and the molecular area $A_m$. Compression speed a was about 30, 40, 50mm/min. also, LB layers of Arachidic acid deposited by LB method were deposited onto slide glass as Y-type film. The structure of manufactured device is Au/Arachidic acid/Al, the number of accumulated layers are 9 ~ 21 and we then examined of the Metal-Insulator-Metal(MIM) device by means of I-V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.266-267
• /
• 2007

$Ba_{0.5}Sr_{0.5}TiO_3$(BST) films with different deposition temperatures were deposited on $Al_2O_3$ substrate by Nd:YAG Pulsed Laser Deposition(PLD). The deposition conditions to achieve high crystal structures and dielectric properties were optimized for both techniques. The structural characterization on the BST thin films was performed by X-Ray Diffraction(XRD) and Atomic Force Microscopy (AFM). Effects of post-deposition annealing of BST films were investigated. The best dielectric properties were obtained on $800^{\circ}C$ deposited BST film with post-deposition annealing at $1100^{\circ}C$ in flowing $O_2$ atmosphere for 2hours.