• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.235-238
• /
• 2009

This paper describes the mechanical properties of poly (Polycrystalline) 3C-SiC thin films with $N_2$ in-situ doping. In this work, the poly 3C-SiC film was deposited by APCVD (Atmospheric Pressure Chemical Vapor Deposition) method using single-precursor HMDS (Hexamethyildisilane: $Si_2(CH_3)_6)$ at $1200^{\circ}C$. The mechanical properties of doped poly 3C-SiC thin films were measured by nono-indentation according to the various $N_2$ flow rate. In the case of 0 sccm $N_2$ flow rate, Young's Modulus and hardness were obtained as 285 GPa and 35 GPa, respectively. Young's Modulus and hardness were decreased according to increase of $N_2$ flow rate. The crystallinity and surface roughness was also measured by XRD (X-Ray Diffraction) and AFM (Atomic Force Microscopy), respectively.

• Preventive Nutrition and Food Science
• /
• v.10 no.3
• /
• pp.224-230
• /
• 2005

The effects of low viscosity chitosan on the rheological properties of soymilk using a model system and on tofu qualities were examined. The flow behavior of soy milk with chitosan closed the Newtonian flow and stabilized according to increasing chitosan concentration. The soymilk containing $glucono-\delta-lactone$ exhibited a more pseudoplastic flow behavior compared with that of the control soymilk. The addition of low viscosity chitosan to the tofu preparation did not significantly affect its physicochemical properties. However, the results of the TEM image and instrumental textural properties showed that low viscosity chitosan affected the construction of the tofu structure. Chitosan tofu had low scores across the whole field of appearance in the sensory evaluation, and its overall eating quality was scored significantly lower. These results suggest that the addition of low viscosity chit os an affects the quality of tofu, which changes according to the degree of polymerization and concentration of chitosan.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.237-244
• /
• 2016

The workability of mortar determines its construction performance in a structure showing its designed resistance to external loads. Measuring the rheological properties of mortar is one way of quantifying its workability, but its field-applications are limited due to economical and spatial issues. The robustness of the slump flow test allows its use for evaluating the workability of mortar, even though it is a rather qualitative test method. This paper proposes a channel flow test and develops a correlation between its result and the rheological properties of mortar. The volume-of-fluid simulation for the channel flow test was accomplished, and a numerical database for the correlation was composed. A correlation model to estimate the rheological properties of mortar using the results of the channel flow test as inputs is proposed.

• Archives of Pharmacal Research
• /
• v.2 no.1
• /
• pp.1-8
• /
• 1979

The flow rate of various sand through circular orifice can be measured from a knowledge of a few easily measurable properties of the system. These are the orifice column and particle diameters, the angle of inclination of the orifice with the horizontal and an angle of repose of the granular sand material. Straight lines were obtained when the logarithm of the flow rate was plotted versus the logarithm of orfice diameter. No influence of excessive compaction and bed height was observed and the flow rate increased with decrease of particle diameter. The profile of flow developed the edge of the aperture in a way independent of its size. Linear relationship was observed between the angle of inclination of the orifice and the flow rate.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.28 no.3
• /
• pp.554-558
• /
• 1999

Flow properties of traditional kochujang at various fermentation times(0~12 weeks) were determined with rotational cylindrical(RC) and serrated plate plate(PP) viscometer. Magnitudes of consistency index(K) of power law model and Cassson parameters(yield stress and viscosity) measured by PP viscometer were higher than those using RC viscometer. All kochujang samples during fermentation were much shear thinning with values of flow behavior index(n) as low as 0.2~0.34. K value and Casson yield stress measured by PP viscometer had good correlations(r=0.94; r=0.91) with fermentation time. No significant changes in flow model parameters measured by RC viscometer were observed for kochu jang during fermentation. Magnitudes of flow model parameters measured by PP viscometer more closely correlated with fermantation times of kochujang than did RC viscometer.

• Korean Journal of Materials Research
• /
• v.15 no.8
• /
• pp.518-520
• /
• 2005

Effects of the $O_2/Ar$ flow ratio in the sputtering process on the crystallinity, surface roughness, carrier concentration, carrier mobility, and optical properties of Al-doped ZnO thin films deposited on sapphire (001) substrates by RF magnetron sputtering were investigated. XRD spectra showed a preferred orientation along the c-axis and a minimum FWHM of the (002) XRD intensity peak for the $O_2/Ar$ flow ratio of 0.5. The (101)peak also appeared and the degree of preferred orientation decreased as the $O_2/Ar$ flow ratio increased from 0.5 to 1.0. AFM analysis results showed that the surface roughness was lowest at the $O_2/Ar$ flow ratio of 0.5 and tended to increase owing to the increase of the grain size as the $O_2/Ar$ flow ratio increased further. According to the Hall measurement results the carrier concentration and carrier mobility of the fan decreased and thus the resistivity increased as the $O_2/Ar$ flow ratio increased. The transmittance of the ZnO:Al film deposited on the glass substrate was characteristic of a standing wave. The transmittance increased as the $O_2/Ar$ flow ratio in-RF magnetron sputtering increased up to 0.5. Considering the effects of the $O_2/Ar$ flow ratio on the surface roughness, electrical resistivity and transmittance properties of the ZnO:Al film the optimum $O_2/Ar$ flow ratio was 0.5 in the RF magnetron sputter deposition of the ZnO:Al film.

• Korean Journal of Mathematics
• /
• v.12 no.2
• /
• pp.171-175
• /
• 2004

The purpose of this paper is to investigate some lifting properties of homomorphisms of flows. It is shown that an almost one to one extension of a minimal proximal flow is proximal. It is also shown that a distal extension of a pointwise almost periodic flow is pointwise almost periodic.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.127-128
• /
• 2009

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.05a
• /
• pp.291-294
• /
• 2003

Ball indentation tests have been used to estimate the mechanical properties of materials by some investigators. In this study, load-depth curves from ball indentation tests have been analysed using the geometric conditions of ball indentation. Series of numerical calculations and experimental results showed that those curves could be simplified by linear functions. After linearizing the indentation curves, the estimation process of the flow properties became straight forward and the scatter of results could be drastically reduced.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.135-136
• /
• 2006

The shear flow properties have been reported in many cases by manufactures and fabricators. Only this characteristic is sometimes insufficient for the processings to provide a complete picture of the relationship between the processability and the flow behavior when underwent free-surface processes in which the shape and thickness of the extrudate are determined by the rheological properties of the melt, the die dimensions etc. In this paper the methodology of control of elongational flow is discussed in terms of relaxation time control of the polymer melts.