• Geomechanics and Engineering
• /
• 제22권5호
• /
• pp.461-473
• /
• 2020

Natural rock mass contains defects of different shapes, usually filled with inclusions such as clay or gravel. The presence of inclusions affects the failure characteristics and mechanical properties of rock mass. In this study, the strength and failure characteristics of rock with inclusions were studied using the particle flow code under uniaxial compression. The results show that the presence of inclusions not only improves the mechanical properties of rock with defects but also increases the bearing capacity of rock. Circular inclusion has the most obvious effect on improving model strength. The inclusions affect the stress distribution, development of initial crack, change in crack propagation characteristics, and failure mode of rock. In defect models, concentration area of the maximum tensile stress is generated at the top and bottom of defect, and the maximum compressive stress is distributed on the left and right sides of defect. In filled models, the tensile stress and compressive stress are uniformly distributed. Failing mode of defect models is mainly tensile failure, while that of filled models is mainly shear failure.

• 대한기계학회논문집B
• /
• 제36권6호
• /
• pp.663-668
• /
• 2012

비산회에 의한 보일러 튜브 마모 문제는 석탄화력 보일러 튜브 파손에 주요한 요인이 된다. 때문에 튜브 보호막이나 다공판 등이 마모 문제 완화를 위하여 사용되고 있다. 그러나 비산회에 의한 튜브마모 문제는 이런 방법을 통하여 완전히 해결될 수 없는데 이는 보일러 마다 유동 조건이 다를 뿐만아니라 예상치 못한 위치에서 국부적으로 마모가 심화될 수 있기 때문이다. 문제는 보일러 내부 비대칭 유동과 국부적 유속 증가에서 기인함으로 튜브 마모 문제의 해결에 있어서 보일러 내부 유동을 명확히 파악하는 것이 무엇 보다 중요하다 하겠다. 본 연구에서는 튜브 마모 문제에 해결을 위해 사용되는 Cold Air Velocity Technique(CAVT)에 대하여 고찰하고 하동화력 2호기 보일러에 대하여 CAVT를 실제 적용함으로써 석탄화력 보일러에 있어서 CAVT 적용 가능성을 검증하였다.

• 한국전산유체공학회지
• /
• 제10권1호
• /
• pp.51-55
• /
• 2005

For proper installation, operation and performance of axial flow jet engines in aircrafts, the impacts and effects of inlet flow distortion in axial compressors have to be understood. Inlet distortion conditions may cause component-mismatch and instability problems known as rotating stall, and severe oscillations of mass flow rate called surge or a combination of both. Typical effects of this phenomenon include stresses and wear on the compressor blading, destruction of entire jet engines due to the failure of airfoil and mechanical failure or interruption of the combustion process. Therefore, it is important to study inlet flow distortion and its propagation effects to minimize and hence to prevent the occurrence of such calamity. The current novel integral method with parametric analysis signifies its validity to this field of research and offers much potential for further improvements. The present effort further indicates that this simple method may be flourishing in the problems of strongly distorted flow and propagating stall in axial compressor. It is therefore believe that using a more realistic and flexible velocity and pressure profiles could develop this approach further.

• Computers and Concrete
• /
• 제31권5호
• /
• pp.443-455
• /
• 2023

This is a research analyses on the bearing capacity at a pile tip embedded in rock. The aim is to propose a shape coefficient for an analytical solution and to investigate the influence of the plastic flow law on the problem. For this purpose, the finite difference method is used to analyze the bearing capacity of various types and states of rock masses, assuming the Hoek & Brown failure criterion, by considering both plane strain and an axisymmetric model. Different geometrical configurations were adopted for this analysis. First, the axisymmetric numerical results were compared with those obtained from the plane strain analytical solution. Then the pile shape influence on the bearing capacity was studied. A shape factor is now proposed. Furthermore, an evaluation was done on the influence of the plastic flow law on the pile tip bearing capacity. Associative flow and non-associative flow with null dilatancy were considered, resulting in a proposed correlation. A total of 324 cases were simulated, performing a sensitivity analysis on the results and using the graphic output of vertical displacement and maximum principal stress to understand how the failure mechanism occurs in the numerical model.

• Interaction and multiscale mechanics
• /
• 제5권2호
• /
• pp.157-168
• /
• 2012

The dilatancy of granular materials has significant influence on its mechanical behaviors. The dilation angle is taken as a constant in conventional associated or non-associated flow rules based on Drucker-Prager yields theory. However, various experimental results show the dilatancy changes during progressive failure of granular materials. A non-associated flow rule with evolution of dilation angle is adopted in this study, and Cosserat continuum theory is used to describe the behaviors of granular materials for considering to some extent the its internal structure. Numerical examples focus on the bearing capacity and localization of granular materials, and results illustrate the capability and performance of the presented model in modeling the effect on failure behavior of granular materials.

• 대한기계학회논문집A
• /
• 제29권7호
• /
• pp.947-954
• /
• 2005

The purpose of this study is to develop failure pressure evaluation models, which are applicable to straight pipes and elbows containing an internally wall thinning defect induced by flow-accelerated-corrosion (FAC). In this study, thus, three dimensional finite element (FE) analyses are performed to investigate the dependences of failure pressure of internally wall thinned pipe on the defect shape, the pipe geometry, and the defect location and bend radius of elbow. Also, the existing failure pressure assessment models for externally wall thinned pipes are examined. Based on these, the new models for assessing failure pressure of piping components with an internally wall thinning defect are proposed. Comparison of failure pressure, predicted by proposed models, with FE analysis result shows good agreement regardless of pipe type, defect shape, and defect location and bend radius.

• Journal of Chest Surgery
• /
• 제31권4호
• /
• pp.402-408
• /
• 1998

1995년 3월 56세 여자환자가 계속 확장하는 만성 Debakey 1형 대동맥 박리증으로 대동맥궁 치환술을 시행하였다. 계속되는 박리의 전후 확장으로 대동맥궁의 혈류가 분리되었고, 가강이 복부대동맥까지 확장되어 있었다. 수술후 3시간 뒤에 갑작스러운 무뇨증이 발생하였고, 도플러 초음파와 대동맥촬영에서 신동맥으로의 혈류가 감소된 것이 발견되었다. 내막피판에 의한 급성 신부전으로 판단하고 대동맥 풍선확장술을 시행하였으나 실패하였다. 응급으로 복부대동맥 개창술을 시행하여 내막피판과 혈전을 제거하였다. 이후 환자는 경한 만성신부전 상태로 투석 치료없이 지내고 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.125.2-125.2
• /
• 2005

• Smart Structures and Systems
• /
• 제30권1호
• /
• pp.49-62
• /
• 2022

Experimental and discrete element methods were used to investigate the effects of triple joints lengths and triple joint angle on the failure behavior of rock mass under uniaxial compressive test. Concrete samples with dimension of 20 cm × 20 cm × 5 cm were prepared. Within the specimen, three imbedded joint were provided. The joint lengths were 2 cm, 4cm and 6 cm. In constant joint lengths, the angle between middle joint and other joints were 30°, 60°, 90°, 120° and 150°. Totally 15 different models were tested under compression test. The axial load rate on the model was 0.05 mm/min. Concurrent with experimental tests, the models containing triple joints, length and joint angle are similar to the experiments, were numerical by Particle flow code in two dimensions (PFC2D). Loading rate in numerical modelling was 0.05 mm/min. Tensile strength of material was 1 MPa. The results show that the failure behaviors of rock samples containing triple joints were governed by both of the angle and the length of the triple joints. The uniaxial compressive strengths (UCS) of the specimens were related to the fracture pattern and failure mechanism of the discontinuities. Furthermore, it was shown that the compressive behavior of discontinuities is related to the number of the induced tensile cracks which are increased by decreasing the joint length. Along with the damage failure of the samples, the acoustic emission (AE) activities are excited. There were only a few AE hits in the initial stage of loading, then AE hits rapidly grow before the applied stress reached its peak. In addition, every stress drop was accompanied by a large number of AE hits. Finally, the failure pattern and failure strength are similar in both methods i.e., the experimental testing and the numerical simulation methods.

• 소성∙가공
• /
• 제12권2호
• /
• pp.134-140
• /
• 2003

Polymers such as polypropylene or polyethylene offer a unique feature of producing an integral hinge, which can flex over a million times without causing a failure. With such advantage manufacturing, time and cost required at the assembly stage can be eliminated by injecting the whole part as one piece. However, due to increased fluidity resistance at hinges during molding, several defects such as short shot or premature hinge failure can occur with the improper selection of gate locations. Therefore, it is necessary to optimize flow balancer in injection molding of part with hinges before actually producing molds. In this paper, resin flow patterns depending on several gate positions were investigated by numerical analyses of a simple strip part with a hinge. As a result, we found that the properly determined gate location leads to better resin flow and shorter hesitation time. Finally, injection molding tryouts using a mold that was designed one of the proposed gate systems were conducted using polypropylene that contained 20% talc. The experiment showed that hinges without defects could be produced by using the designed gate location.