• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.1
• /
• pp.83-90
• /
• 2020

A commercial flow measurement radar sensor estimates a quantity of flowed water using surface flow rate. In this way, the amount of water flowing per unit time cannot be measured accurately because of using an estimation result and it can't response environmental changes. For more accurate flow measurements we need width of waterway, water level and distance that water moved per unit time. Commonly two sensors are used to measure water level and flow rate. In this paper, we propose a method to simultaneously measure the water level and surface flow velocity using a single FMCW radar sensor and design the transmission waveform. In order to verify the waveform design, received signal is modelled based on transmission waveform. In addition, we consider phenomenons and problems that may occur in signal processing.

• The Journal of the Korea Contents Association
• /
• v.17 no.2
• /
• pp.535-542
• /
• 2017

There is a big difference of discharge rate between drought and flood period in Korea since the importance of water resources management has come to the fore. To know a river characteristics, it needs to estimate river discharge accurately. River discharge is calculated using the measured velocity of cross section and the estimated area of watercourse as input parameters into continuity equation. Generally, flow rate over a river is estimated from the relation equation between level and discharge, in this case, there are weakness for only the equal depths and the equal discharge estimated. In the present study, therefore, water surface slope was estimated using measured water level of Seongseo water level observation station and measured water level using ADVM at Gangchang Bridge. And then, we developed the discharge calculation equation using water surface slope. A method to easily calculated flow rate from the measured depth of the two points that are suggested by reflecting water surface slope because natural stream is unsteady flow, not uniform flow or not steady flow.

• Journal of Advanced Navigation Technology
• /
• v.24 no.1
• /
• pp.16-27
• /
• 2020

This paper investigates the applicability of optical flow information for unmanned aerial vehicle (UAV) navigation under environments where global navigation satellite system (GNSS) is unavailable. Since the optical flow information is one of important measurements to estimate horizontal velocity and position, accuracy of the optical flow information must be guaranteed. So a navigation algorithm, which can estimate and cancel biases that the optical flow information may have, is suggested to improve the estimation performance. In order to apply and verify the proposed algorithm, an integrated simulation environment is built by designing a guidance, navigation, and control (GNC) system. Numerical simulations are implemented to analyze the navigation performance using this environment.

• Journal of Korean Society on Water Environment
• /
• v.33 no.3
• /
• pp.311-325
• /
• 2017

Habitat suitability index (HSI) of 17 benthic macroinvertebrate taxa, which were lotic insects of generic category except Potamanthidae in mayfly, was developed for three physical habitat factors (current velocity, water depth and substrate) based on an ecological monitoring in a Korean stream (Gapyeong). Weibull model was used as a probability density function to analyze the distribution of individual abundance related with physical factors, which showed it was so available. Number of species and total individual abundance increased along with the increase of current velocity and the mean diameter of substrate, and decreased along with the increase of water depth. Most taxa showed a clear preference for a fast current velocity, shallow water depth and coarse substrate except Ephemera, Potamanthidae (mayfly), and Plectrocnemia (caddisfly) which were rheophobic, potamophilic and lithophobious. Based on the canonical correspondence analysis, the relative importance of each factor was determined as follows: current velocity > substrate > water depth.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.7
• /
• pp.917-927
• /
• 2018

High blood pressure causes various cardiovascular diseases and is associated with mortality. Periodic self-monitoring and recording of blood pressure is very helpful in preventing the occurrence of secondary diseases caused by hypertension. However, existing cuff-type blood pressure monitors have many limitations. As an alternative of that, a method of estimating the blood pressure by measuring the velocity change of the blood flow using the photo plethysmography is widely known. However, photo plethysmography have a low correlation with blood flow. So, we will propose an algorithm for estimating blood pressure using the relationship between velocity change of blood flow measured by magnetic field instead of photo plethysmography and electrocardiogram. For this purpose, First, we analyzed the correlation between photo plethysmography and magneto plethysmography. the correlation between MPG and PPG was r = 0.9449. Second, we compared estimated blood pressure and measured blood pressure. In the four experiment each result was r = 0.5737, r = 0.7863, r = 0.5669, and r = 0.7445.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.8 no.4
• /
• pp.287-296
• /
• 1996

A mathematical model for the dynamic analysis of the riser system is developed to investigate the effect of internal flow on the free vibration of marine riser system which includes a steady flow inside the pipe. A semi-analytical method using series expansion is employed to derive Eigenvalue problem to facilitate the evaluation of the system frequencies, and its validity is given through the comparison of the solutions with the conventional method using system matrices. The algorithm is implemented to develop computer programs for the estimation of the system frequency. The investigations of the effect of internal flow on system frequency are performed according to the change of parameters such as top tension, internal flow velocity, and so on. It is found that the effect of internal flow can be controlled by the increase of top tension. However, careful consideration has to be given in the design point, particularly for the long riser.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.1
• /
• pp.237-242
• /
• 2017

Along with effluence of non-point pollution source, continuous precipitation due to rainy season or localized heavy rain can also be a good reason for increase of flow rate. And if the water level is going up due to the increase, floating debris around rivers and streams will move because of increased flow velocity. However, currently, there are no studies which perform quantitative calculation on movement of floating debris by analyzing amount of rainfall and flow rate in both domestic and abroad. Thus, the present study calculated amount of movement of floating debris based on moving route monitoring results according to changes of effective rainfall and flow rate that are obtained by using SCS-CN method.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.9 s.114
• /
• pp.904-911
• /
• 2006

A modified energy method for the fretting wear of the steam generator tube is proposed to calculate the wear-out depth between the nuclear steam generator tube and its support. Estimation of fretting-wear damage typically requires a non-linear dynamic analysis with the information of the gap velocity and the flow density around the tube. This analysis is very complex and time consuming. The basic concept of the energy method is that the volume wear rate due to the fretting-wear phenomena Is related to work rate which is time rate of the product of normal contact force and sliding distance. The wearing motion is due to dynamic interaction between vibrating tube and its support structure, such as tube support plate and anti-vibration bar. It can be assumed that the absorbed work rate would come from turbulent flow energy around the vibrating tube. This study also numerically obtains the wear-out depth with various wear topologies. A new dissection method is applied to the multi-span tubes to represent the vibrational mode. It turns out that both the secondary side density and the normal gap velocity are important parameters for the fretting-wear phenomena of the steam generator tube.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.12 s.255
• /
• pp.1155-1163
• /
• 2006

Calculation was carried out for phase velocity and deformation wave decay in a layer of viscoelastic material fixed tightly on the solid substrate. Analysis has been performed regarding the inner structure of the wave, i.e., the proportions between the vertical and horizontal displacements and their profiles. The wave characteristics depend strongly on media compressibility factor. The effect of viscous losses on parameters of the main oscillation mode was studied in detail. Results were compared with the model of coating with local deformation. A new experimental approach was made in order to measure such wave properties of a compliant coating as the dependency of deformation wave velocity on frequency and decay factor was made. The method for estimation of coating parameters enabling the drag reduction in turbulent flow was then refined.

• Journal of KIISE:Computing Practices and Letters
• /
• v.16 no.5
• /
• pp.621-625
• /
• 2010

This paper presents a hand motion tracking method for hand gesture interface using a camera in mobile devices such as a smart phone and PDA. When a camera moves according to the hand gesture of the user, global optical flows are generated. Therefore, robust hand movement estimation is possible by considering dominant optical flow based on histogram analysis of the motion direction. A continuous hand gesture is segmented into unit gestures by motion state estimation using motion phase, which is determined by velocity and acceleration of the estimated hand motion. Feature vectors are extracted during movement states and hand gestures are recognized at the end state of each gesture. Support vector machine (SVM), k-nearest neighborhood classifier, and normal Bayes classifier are used for classification. SVM shows 82% recognition rate for 14 hand gestures.