• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07b
• /
• pp.1288-1290
• /
• 2005

We report on the structural and electrical properties of amorphous Yttria-stabilized zirconia (YSZ) thin films which are the potential high-k gate dielectric material of organic thin film transistor (OTFT). To investigate the influence of the oxygen flow rate on the structural and electrical properties of the YSZ films, XRD, XPS, J-E, I-V were carried out in this work. Oxygen vacancies are expected to be the most predominant type of defect in metal-oxide dielectrics. The leakage current density decreased mainly because of the reduction of oxygen vacancies with increasing oxygen flow rate.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.6
• /
• pp.915-922
• /
• 2008

The gas separation technology using membrane is widely used to refine various gases in many industry fields and recently is being applying in $CO_2$ recovery technology. In the gas and chemical tanker. nitrogen generators for inerting, purging and padding are on board and most of them have membrane modules of hollow fiber type with long life and vibration resisting properties. Because a membrane module is a key component accounting for 50% of total manufacturing cost of nitrogen generator, adequate selection for it is an important problem. In this paper, the flow performance coefficient based on dimension and specification data of membrane module was relatively selected to compare nitrogen generating capacity of module and various performance tests about the selected PARKER ST6010 membrane module were conducted. As a result, the useful coefficient and basic data in selecting a membrane module were achieved.

• Journal of computational fluids engineering
• /
• v.12 no.2
• /
• pp.46-52
• /
• 2007

An experimental and numerical investigation of the ejector-jets focusing on its geometric parameters that effect on thrust performance was carried out. The area ratio of the primary nozzle that was tested in the present study was 2.17 and 3.18, while the ratio of the length to the diameter of the duct downstream the primary nozzle inlet had values of 3.41, 6.82, and 10.23. Internal flow properties of ejector-jet were estimated by comparison experiment data and CFD analysis for basic study of ejector-jet thrust performance. For examination of thrust performance, the thrust ratios increased with increase in L/D. Especially at AR=2.17, the maximum thrust augmentation was 33 percent for the shortest L/D. It is expected that the increase of mixing duct length of ejector-jet will be helpful in a thrust performance by improving mixing efficiency.

• YAKHAK HOEJI
• /
• v.35 no.4
• /
• pp.277-282
• /
• 1991

Rheological, colloidal and micromeritical properties were followed to investigate aging mechanisms of hydrous aluminum oxide suspension using Zeta-meter systems, BET adsorption apparatus, Master sizer and electronmicroscope. The results indicate that hydrous aluminum oxide suspension revealed plastic flow with thixotropy. The viscosity, thixotropy and yield value were increased with increasing concentration. During aging process, the viscosity and thixotropic index were increased by an addition of glycerin, however, sorbitol stabilized aging process of the suspension being accompanied with growth of particle size and reduction in specific surface area, pore area and pore volume, and consistency. Diminution of adsorptive power of the particles was also protected by addition of sorbitol to hydrous aluminum oxide suspension. From these results, one of aging mechanism of hydrous aluminum oxide suspension assumed growth and/or crystallization of colloidal particles in aqueous suspension.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1995.10a
• /
• pp.69-75
• /
• 1995

The deformation behavior of stainless steel-clad aluminum sheet metals under uniaxial tension has been investigated. The differences in mechanical properties such as elastic modulus, flow stress and plastic strain ratio, of component layers of the composite sheet gave rise to warping of the tensile specimens. The warping has been analyzed by FEM and the total force and momentum equilibria. The analyzed radii of curvature of the warped specimens were smaller than the measured data possibly due to elastic recovery during unloading. The differences in mechanical properties may also give rise to transverse stresses in the component layers. The transverse stresses have been analyzed on the assumption of isostrain and by the FEM in which the warping has been taken into account. The transverse stresses calculated by the FEM were lower than those by the isostrain hypothesis due to stress relaxation by the warping and turned out to be negligible compared with the longitudinal stresses. Consequently, the flow stresses of the composite sheets follow the rule of mixtures.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.04a
• /
• pp.89-92
• /
• 2000

In this paper, setting and mechanical properties of cement mortar using retarding agents are investigated. According to the experimental results, as dosage of retarding agents increases, flow and ar content of mortar are shown to be higher. Flow loss of mortar using retarding type water reducing agents is larger than that using gluconic acid by 3 times. As for setting time it is found that mortar using gluconic acid takes much longer setting time than that using retarding type water reducing agent. In case of compressive strength, when retarding agent is applied, cement mortar gains high strength compared with that of plain mortar. However, we can not measure compressive strength of cement mortar contaning more than 0.6% of gluconic acid.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.51-56
• /
• 1997

This study is aimed for investigating the influence of mortar on improved of surface shape of crushed sand, and analyzing the physical properties of fresh state and hardened state. By the test results, it was found that the flow value and bleeding ratio was increased, but the change of flow value according to time was decreased with the improved surface shape of crushed sand. Also, comparing improved of surface shape of crushed sand with not improved of surface shape of crushed sand on strength, compressive strength is about the same and flexural strength decrease in case of improved of surface shape of crushed sand.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.1077-1080
• /
• 2003

High reactivity metakaolin (HRM) is a manufactured pozzolan produced by thermal processing of purified kaolinitic clay. Field performance and laboratory research of concrete containing HRM have demonstrated its value for bridge decks, bridge deck overlays, high-strength concrete and masonry products. This paper discusses laboratory evaluations to assess the physical properties of antiwashout underwater concrete (AWC) containing HRM, such as pH value, suspended solids, slump flow, and compressive strength. There were not much variations of pH value with the changing HRM contents, but suspended solid test showed that the amount of suspended solids of AWC with 10 and 20% of HRM were reduced in comparison with plain. Due to the fast hydration and reaction property of HRM, slump flow was decreased with increasing HRM contents. According to the results of compressive strength test, AWC with 10 and 20% of HRM showed higher strength characteristic than plain at all curing ages.

• 한국전산유체공학회:학술대회논문집
• /
• 2007.04a
• /
• pp.166-170
• /
• 2007

An experimental and numerical investigation of the ejector-jets focusing on its geometric parameters that effect on thrust performance was carried out. The area ratio of the primary nozzle that was tested in the present studywas 2.17 and 3.18, while the ratio of the length to the diameter of the duct downstream the primary nozzle inlet had values of 3.41, 6.82, and 10.23. Internal flow properties of ejector-jet were estimated by comparison experiment data and CFD analysis for basic study of ejector-jet thrust performance. For examination of thrust performance, the thrust ratios increased with increase in L/D. Especially at AR=2.17, the maximum thrust augmentation was 34 percent for the shortest L/D. It is expected that the increase of mixing duct length of ejector-jet will be helpful in a thrust performance by improving mixing efficiency.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2010.05a
• /
• pp.56.2-56.2
• /
• 2010

An improvement in the optical and structural properties of p-GaN was obtained by using antimony (Sb) as a surfactant during p-GaN growth. Two different growth temperatures of p-GaN such as $1030^{\circ}C$ and $900^{\circ}C$ were considered. Keeping the growth conditions for p-GaN constant, Sb was introduced during p-GaN growth while varying the [Sb]/([Ga]+[Mg]) flow ratio. [Sb]/([Ga]+[Mg]) flow ratio will be denoted as SGM ratio for convenience. SGM ratio of 0, 0.015 and 0.03% were considered for high temperature p-GaN growth. SGM ratio of 0, 0.005, 0.01 and 0.02% were considered for low temperature p-GaN growth. The analysis results suggest that using the optimum SGM ratio during p-GaN growth greatly improves the optical and structural properties of the p-GaN.