• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.04a
• /
• pp.60-61
• /
• 2006

In this paper, the inorganic-organic thin film encapsulation layer was newly adopted to protect the organic layer from moisture and oxygen. Using the electron beam, Sputter and Spin-Coater system, the various kinds of inorganic and organic thin-films were deposited onto the Ethylene Terephthalate(PET) and their interface properties between organic and inorganic layer were investigated. Results indicates that the SiON/PI/SiON/PI/PET barrier coatings have high potential for flexible organic light-emitting diode(OLEO) applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.615-616
• /
• 2005

Carbon Nanotubes (CNT) on flexible indium tin oxide (ITO) PET films were prepared for dye-sensitized solar cell (DSSC). These CNTs were prepared by spray coating method for various amount of light transparency. Also, Pt counter electrode was prepared by electro deposition method. All $TiO_2$ electrodes were deposited on ITO-PET films by spray coating method. Micro structural images show that CNT counter electrodes prepared by spray-coating have more dense structure with increasing spraying time (0 to 60 seconds). DSSC consisting of $TiO_2$ electrode and CNT counter electrode was fabricated with various amount of light absorption. DSSC have higher light energy conversion efficiency with increasing the thickness of CNT counter electrode. CNT counter electrode is at least compatible to that of CNT counter electrode.

• Radiation Oncology Journal
• /
• v.7 no.2
• /
• pp.299-303
• /
• 1989

Authors have developed highly reproducible calibration method for the Micro-Selectron HDR Ir-192 system (Nucletron, Motherland). The new jig has a 10cm radius circular hole in the $30cm{\times}30cm{\times}0.2cm$ acrylic plate, and 5F flexible bronchial tubes are attached around the hole. The source moves along the circle in the tubes and the ionization chamber is placed verticaly at the center of the circular hole (center of the jig). Dose distribution near the center was derived theoretically, and measured with the film dosimetry system. Theoretical calculation and measurement show the error margin below $0.1\%$ for 1mm or 2mm position deviation. We have measured at 12 and 24 points of circle with 1, 6, 11 and 21 second dwell time of source in order to calculate the activity of the source. Measurements have been repeated daily for 50 days. The accuracy and the reproducibility are below $1\%$ error margin. The half life of the source from our measurement is estimated $73.4\pm0.4$ days.

• Journal of the Korean Society for Heat Treatment
• /
• v.29 no.5
• /
• pp.216-219
• /
• 2016

$SnO_2$ single layer films (100 nm thick) and 2 nm thick Ni intermediated $SnO_2$ films were deposited on glass substrate by RF and DC magnetron sputtering without intentional substrate heating and then the influence of the Ni interlayer on the electrical and optical properties of the films were investigated. As deposited $SnO_2$ single layer films show the optical transmittance of 82.6% in the visible wavelength region and a resistivity of $6.6{ \times}10^{-3}{\Omega}cm$, while $SnO_2/Ni/SnO_2$ trilayer films show a lower resistivity of $2.7{ \times}10^{-3}{\Omega}cm$ and an optical transmittance of 76.3% in this study. Based on the figure of merit, it can be concluded that the intermediate Ni thin film effectively enhances the opto-electrical performance of $SnO_2$ films for use as transparent conducting oxides in flexible display applications.

• Journal of the Korean institute of surface engineering
• /
• v.47 no.6
• /
• pp.347-353
• /
• 2014

We present a synthesis of single-walled carbon nanotubes(SWNTs) for enhancement of parallel-alignment and density using chemical vapor deposition with methane feed gas. As-purchased ST-cut quartz substrates were heat-treated and line-patterned by electron-beam lithography in order to grow SWNTs with parallel alignment. We investigated the effects of various synthesis parameters such as catalyst oxidation, reduction, and synthesis conditions in order to enhance both tube density and degree of parallel alignment. The condition of $1{\AA}$ of Fe catalyst film, atmospheric oxidation at $750^{\circ}C$ for 10 min, reduction under 400 Torr for 5 min, and growth at $865^{\circ}C$ under 300 Torr yields $33tubes/10{\mu}m$, which is the highest tube density with parallel alignment. Based on the results of atomic force microscope and Raman spectroscopy, it was found that SWNTs have diameter range of 0.8-2.0 nm. We believe that the present work would contribute to the development of SWNTs-based flexible functional devices.

• Journal of Sensor Science and Technology
• /
• v.28 no.1
• /
• pp.47-51
• /
• 2019

Sweat-based glucose sensors are being widely investigated and researched as they facilitate painless and continuous measurement. However, because the concentration of sweat glucose is almost a hundred times lower than that of blood glucose, it is important to develop electrochemical sensing electrode materials that are highly sensitive to glucose molecules for the detection of low concentrations of glucose. The preparation of a flexible and ultra-sensitive sensor for detection of sweat glucose is presented in this study. Oxygen and nitrogen are removed from the surface of a polyimide film by exposure to a CO2 laser; hence, laser-induced graphene (LIG) is formed. The fabricated LIG electrode showed favorable properties of high roughness and good stability, flexibility, and conductivity. After the laser scanning, Pt nanoparticles (PtNP) with good catalytic behavior were electrodeposited and the glucose sensor thus developed, with a LIG/PtNP hybrid electrode, exhibited a high order of sensitivity and detection limit for sweat glucose.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.5
• /
• pp.432-436
• /
• 2019

In this study, we produced a light, flexible, wearable gas sensor by depositing MWCNTs (Multi-walled Carbon Nanotubes) into nylon. MWCNTs are widely used as a gas sensor material due to their excellent mechanical, electrical and physical characteristics. We produced a gas sensor to detect NOx gases by depositing nylon yarn in a MWCNT solution. The MWCNT solution was made by mixing 3 mg MWCNT in 5 ml of ethanol. Nylon yarn was placed in the manufactured solution and ultrasonic waves were applied using an ultrasonicator for 3 h, resulting in MCWNT deposition. The MWCNT-deposited nylon yarn was dried at room temperature for 24 h. The MWCNT-thin-film-coated nylon yarn was masked 1 mm apart, and gold was then deposited on the masked nylon yarn to create the gas sensor. The sensor then was installed in a chamber with a controlled atmospheric environment and exposed to NOx gas. The changing signal from the sensor was amplified to analyze its gas detection characteristics.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.27 no.1
• /
• pp.35-40
• /
• 2021

Calcium hydroxide (CH) reacts with CO2 to produce moisture, and sodium carbonate (SC) reacts with CO2 in the presence of moisture. Using these different characteristics of these two reactants, a CH/SC mixture of CO2 absorber tuned for kimchi ripening to produce CO2 in a flexible package was selected. A ratio of CH:SC (1:2) in highly gas permeable microporous spunbonded film (Tyvek) sachet was found to be appropriate for delayed and consistent CO2 absorption useful for kimchi package. Addition of superabsorbent polymer (SAP) as moisture buffer was helpful for boosting the consistency of CO2 absorption. In a package of 0.5 kg kimchi at 10℃, the sachet consisting of 0.794 g of CH + 2.276 g of SC + 0.4 g of SAP suppressed its volume expansion and maintained a suitable range of CO2 partial pressure (PCO2) steadily inside. These optimal conditions may vary depending on the type and salinity of kimchi, storage and distribution temperature, and the material and area of the absorber sachet. This study showed a potential of mixture CO2 absorber to be tuned for CO2 producing packaged kimchi for the purpose of keeping consistent PCO2 at tolerable volume expansion.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.1
• /
• pp.37-43
• /
• 2022

In this study, we investigated the optical, electrical and exothermic characteristics of ITO/Ag/ITO multilayer structures prepared with various Ag thicknesses on quartz and PI substrates. The transparent conducting properties of the ITO/Ag/ITO multilayer films depended on the thickness of the mid-layer metal film. The ITO/Ag (14 nm)/ITO showed the highest Haccke's figure of merit (FOM) of approximately 19.3×10^-3 Ω^-1. In addition, the exothermic property depended on the substrate. For an applied voltage of 3.7 V, the ITO/Ag (14 nm)/ITO multilayers on quartz and PI substrates were heated up to 110℃ and 200℃, respectively. The bending tests demonstrated a comparable flexibility of the ITO/Ag/IT multilayer to other transparent electrodes, indicating the potential of ITO/Ag/ITO multilayer as a flexible transparent conducting heater.

• Prospectives of Industrial Chemistry
• /
• v.23 no.6
• /
• pp.25-36
• /
• 2020

용액공정을 통해 유기 전자소자를 대면적으로 제조하는 것은 다양한 장치 구성 요소(반도체, 절연체, 도체)의 패터닝 및 적층이 필요하기 때문에 매우 어려운 과제이다. 본 연구에서는 4개의 광 가교 기능기를 가지는 3차원 사면체 가교제인 (2,2-bis(((4-azido-2,3,5,6-tetrafluorobenzoyl)oxy)methyl)propane-1,3-diyl bis(4-azido-2,3,5,6-tetrafluorobenzoate) (4Bx)를 활용하여 용액공정을 기반으로 형성된 전자재료 박막을 고해상도로 패터닝 및 적층하는 기술을 개발하고, 이를 사용하여 고분자 박막 트랜지스터(PTFTs) 및 논리회로 어레이 제작을 진행하였다. 4Bx는 다양한 용액공정이 가능한 전자재료와 용매에 쉽게 혼합될 수 있으며, 자외선(UV)에 의해 가교제가 광 활성화되어 전자재료와 가교 결합을 형성할 수 있다. 4Bx는 기존의 2개의 광 가교 기능기를 갖는 가교제에 비해 높은 가교 효율로 인해 적은 양을 첨가하여도 완전하게 가교된 전자재료 박막을 형성할 수 있어 전자재료의 고유한 특성을 보존할 수 있다. 더욱이, 가교된 전자재료 박막은 화학적 내구성이 향상되어 고해상도 미세 패터닝을 할 수 있을 뿐만 아니라 용액공정을 통해 전자소자를 구성하는 전자재료의 적층이 가능하다. 4Bx의 광 가교 방법은 전용액공정을 통한 전자소자의 제작에 대한 혁신적인 방안을 제시한다.