• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.187-199
• /
• 2011

The main objective of this study was investigation of natural gas flames in a lean premixed swirl-stabilized dump combustor with an attention focused on the effect of the various fuel-air mixing section geometry on the combustion instability characteristics. The multi-channel dynamic pressure transducers were located on the combustor and inlet mixing section region to observe combustion pressure oscillation and difference phase at each dynamic pressure measurement results. Dynamic pressures were also measured to investigate characteristics of combustion at the same time. The combustor and mixing section length was varied in order to have different acoustic resonance characteristics from 800 to 1800 mm in combustor and 470, 550, 870 mm in mixing section. We observed two dominant instability frequencies in this study. Lower frequencies were obtained at lower equivalence ratio region and it was associated with a fundamental longitudinal mode of combustor length. Higher frequencies were observed in higher equivalence ratio conditions. It was related to secondary longitudinal mode of coupled with the combustor and mixing section. In this instability characteristics, pressure oscillation of mixing section part was larger than pressure oscillation of combustor. As a result, combustion instability was strongly affected by acoustic characteristics of combustor and mixing section geometry.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.5
• /
• pp.72-83
• /
• 2010

Experiments were conducted to investigate the effects of added diluents (carbon dioxide, nitrogen, and helium) on cellular instabilities in outwardly propagating spherical syngas-air premixed flames. Laminar burning velocities and Markstein lengths were measured by analyzing high-speed schlieren images at various diluent concentrations and equivalence ratios. Experimental results showed substantial reduction of the laminar burning velocities and of the Markstein lengths with the diluent additions in the fuel blends. Effective Lewis numbers of helium-diluted syngas-air flames increased but those of carbon dioxide- and nitrogen-diluted syngas-air flames decreased in increase of diluents in the reactant mixtures. With helium diluent, the propensity for cells formation was significantly diminished, whereas the cellular instabilities for carbon dioxide- and nitrogen-diluted syngas-air flames were not suppressed.

• Journal of the Korean Society of Costume
• /
• v.53 no.8
• /
• pp.121-135
• /
• 2003

The purpose of this study is to suggest a theoretical basis to name Sa(紗) and Ra(羅) remains properly by comparing and analyzing the name, usage, value, length and width of Sa(紗) and Ra(羅) recorded on documents made at the end period of Joseon. The features of Sa(紗) and Ra(羅) at the end of the Joseon Period are as follows. 1. The kinds of Sa(紗) are about 80, those of Ra(羅) are about 12, and those of Sa(紗) are significantly more than those of Ra(羅). In regard to the aspect of patterns, there were about 20 types of patterns in the case of Sa(紗), but no specific pattern for Ra(羅). 2. Some newly revealed patterns in the case of Sa (紗) are as follows. Baek -bok-mun(백복문) was a pattern full of ‘bats(박쥐[복])’, and Baek-jeop-mun(백접문) was a pattern full of ‘butterflies(나비[蝶])’ Jeop-mun(접문) was classified into ‘butterfly patterns(나비문[접문])’ and ‘traditional window flame patterns(창살문[접문])‘. 3. When considering the usages of Sa(紗) and Ra(羅), Sa(紗) was used for various detailed purposes according to their kinds and patterns, but Ra(羅) was mostly used for underwear. The most commonly used Sa(紗) was the Gab-sa type(甲紗類). On the contrary, the Go-sa type(庫紗類) was significantly less used than the Gab-sa type(甲紗類). However, it must have been of relatively high quality Sa(紗), shown by the fact that it was used for outer garments. In addition, the Gung-sa type(宮紗類) was the best quality Sa(紗), shown by the fact that it was used for court dress and official uniforms in the royal court. 4. Sa(紗) and Ra(羅) whose features have been examined we Gapsa(甲紗), Sun-in (純仁), Gosa(庫紗), Gwansa(官紗), Jusa(走紗), Eunjosa(은조사), Gwangsa(廣紗), Waesa(倭紗), Dorisa(도리사), Gong-yangsa(공양사), Rasa(羅紗), Danghangra(唐亢羅), Yanghangra(洋亢羅), Yunjura(윤주라), Eunra(銀羅), Jeohangra(저항라), Chura(秋羅). 5. Regarding the values of Sa(紗) and Ra(羅), they were high quality textures and its length and width of 1 Pil(疋), a roll of cloth, were not subdivided in detail such as in the case of plain weaved silks(平絹).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.4
• /
• pp.57-69
• /
• 2012

The main objective of this study was investigation of natural gas flames in a lean premixed swirl-stabilized dump combustor with an attention focused on the effect of the various fuel-air mixing section geometry on the combustion instability characteristics. The combustor and mixing section length was varied in order to have different acoustic resonance characteristics from 800 to 1800 mm in combustor and 470, 550, 870 mm in mixing section. We observed two dominant instability frequencies in this study. Lower frequencies were associated with a fundamental longitudinal mode of combustor length. Higher frequencies were related to secondary longitudinal mode of coupled with the combustor and mixing section. As a result, combustion instability was strongly affected by acoustic characteristics of combustor and mixing section geometry.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.12-23
• /
• 2021

In this study, the combustion instability characteristics of low-swirl injector and high-swirl injector is compared by model gas turbine combustor. To compare of unstable behavior in high-swirl injector and low-swirl injector, we performed lots of measurement of combustion instability, with variable of equivalence ratio, combustor length and injector type. The results shown that longitudinal instability occur dominantly in model gas turbine combustor. In addition, it was found that high-swirl injector has more wide range of unstable regime than low-swirl injector. The blockage ratio what one of a parameter in low-swirl injector has not much effected in aspects of overall combustor behavior. Also, revealed that combustion instability occurred in the same combustor length has same properties, regardless of the injector type.

• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.84-96
• /
• 2022

In the worst case, a temporary ignition source (also known as transient combustibles) between two electrical panels can damage both panels. Mitigation strategies for electrical panel fires were previously developed using fire modeling and risk analysis. However, since they do not comply with deterministic fire protection requirements, it is necessary to analyze the boundary values at which combustibles may damage targets depending on various factors. In the present study, a sensitivity analysis of input variables related to the damage threshold of two electrical panels was performed for dimensionless geometry using a Fire Dynamics Simulator (FDS). A new methodology using a damage evaluation map was developed to assess the damage of the electrical panel. The input variables were the distance between the electrical panels, the vertical height of the fuel, the size of the fire, the wind speed and the wind direction. The heat flux was determined to increase as the vertical distance between the fuel and the panel decreased, and the largest heat flux was predicted when the vertical separation distance divided by one half flame length was 0.3-0.5. As the distance between the panels increases, the heat flux decreases according to the power law, and damage can be avoided when the distance between the fuel and the panel is twice the length of the panel. When the wind direction is east and south, to avoid damage to the electrical panel the distance must be increased by 1.5 times compared to no wind. The present scale model can be applied to any configuration where combustibles are located between two electrical panels, and can provide useful guidance for the design of redundant electrical panels.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.5A
• /
• pp.747-756
• /
• 2008

The purpose of this paper is to investigate the effect of the important parameters on the transfer length during the dynamic flame cutting of tendon experimentally. The considered parameters were strand diameter, concrete cover thickness, stirrup, debonding strand and release method. Ten pretensioned concete beam specimens were cast and tested. Time history curves for the axial strain of tendon were measured by electrical resistance strain gauges mounted on the strands. Experimental results indicated that large dynamic shock effects occurred near cut-end during the sudden release. The prestressing forces are dependent on the parameters above considered. The ratio of residual prestressing forces of 12.7 mm strands is greater than 15.2 mm strands. Using debonding strand and gradual release are more efficient for applying prestressing forces.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.2
• /
• pp.270-279
• /
• 2000

Recently, according to increase in the requirement of electric power, a thermoelectric power plant equipped with pulverized coal combustion system is highly valued, because coal has abundant deposits and a low price compared with others. For efficient use of coal fuel, most of plant makers are studying to improve combustion performance and flame stability, and reduce pollutants emission. One of these studies is how to control the profile of particle injection and velocity dependant on coal nozzle configuration. Basically, nozzle which has mixed flow of gas and particle is required to have the balanced coal concentration at exit, but it is very difficult to obtain that by itself without help of other device. In this study, coal distribution and pressure drop in gas-solid flow are calculated by numerical method in nozzle with various shapes of venturi diffuser as a means to get even coal particle distribution. The tentative correlations of pressure drop and exit coal distribution are deduced as function of the height, length and reducing angle of venturi from the calculated results. When coal hurner nozzle is designed, these equations are very useful to optimize the shape of venturi which minimize uneven particle distribution and pressure drop within coal nozzle.

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.255-260
• /
• 2005

To achieve efficient combustion within a manageable length, a successful fuel injection scheme must provide rapid mixing between the fuel and airstreams. The aim of the present numerical research is to investigate the flame holding and combustion enhancement. Additional fuel into the cavity prevents shear flow impingement on the trailing edge of the cavity. The high temperature freestream flow mixes with the cold hydrogen fuel that is injected into the cavity and raises the fuel temperature remarkably and become to start combustion. The high pressure in the cavity due to the cavity structure and combustion leads the hydrogen fuel to upstream. The shock in the cavity to be generated by the fuel injection joins together and reflects off the ceiling wall. This makes high pressure and low mach number region and makes a small recirculation in this region. This high stagnation temperature is nearly recovered in the shear layer in front of the cavity and leads to start combustion. In the downstream of the cavity, the wall pressure drops significantly. This means that the combustion phenomenon is diminished. Because fuel lumps at the trailing edge of the cavity then it spreads after the cavity so, in this region there is a strong expansion.

• Journal of the Korean Society of Combustion
• /
• v.15 no.4
• /
• pp.65-73
• /
• 2010

In order to provide fundamental information for developing reaction model in the practical blended coal power plants, effects of particle size and blending ratio on combustion characteristics and thermal reaction in co-firing with bituminous and sub-bituminous coals were experimentally investigated using a TGA and a laboratory-scale burner. Characteristic parameters including ignition, burnout temperature and activation energy were determined from TG and DTG combustion profiles. Distributions of flame length and mean particle temperature were investigated from the visualization of flames in slit-burner system. As coal particle size decreased and volatile matter content increased, characteristic temperatures and activation energy decreased. The ignition/burnout characteristics and activation energy are linearly influenced by a variation in particle size and blending ratio. These results indicated that the control of the coal blending ratio can improve the combustion efficiency for sub-bituminous coals and the ignition characteristics for bituminous coals.