• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1661-1668
• /
• 2016

A fixed off-time controlled high power factor ac-dc LED driver is proposed in this paper, which employs a novel zero-crossing-compensation (ZCC) circuit based on a fixed off-time controlled scheme. Due to the parasitic parameters of the system, the practical waveforms have a dead region. By detecting the zero-crossing boundary, the proposed ZCC circuit compensates the control signal VCOMP within the dead region, and is invalid above this region. With further optimization of the parameters KR and Kτ of the ZCC circuit, the dead zone can be eliminated and lower THD is achieved. Finally, the chip is implemented in HHNEC 0.5μm 5V/40V HVCMOS process, and a prototype circuit, delivering 7~12W of power to several 3-W LED loads, is tested under AC input voltage ranging from 85V to 265V. The test results indicate that the average total harmonic distortion (THD) of the entire system is approximately 10%, with a minimum of 5.5%, and that the power factor is above 0.955, with a maximum of 0.999.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.12
• /
• pp.43-53
• /
• 2007

We have analyzed low current operation characteristics of a VCSEL transmitter operating at fixed Current over wide temperature range. Used 850 nm oxide VCSEL has low temperature dependence of the threshold current and $d^2I_{th}/dT^2$ is approximately $1.346\times10^{-4}mA/^{\circ}C^2$. We fixed on-current so that output power from the chip is 1 mW at $20^{\circ}C$ and investigated the turn-on, turn-off characteristics and eye-diagram of the 850 nm oxide VCSEL transmitter with varying ambient temperature and off-current. We measured rise time, fall time, extinction ratio and timing jitter by changing tile ambient temperature and off-current. With the fixed off-current of around $0.1\sim0.2mA$ lower than the lowest threshold current the transmitter successfully operated at 1.25 Gbps over a wide temperature range from $-20^{\circ}C$ to $80^{\circ}C$.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.7C
• /
• pp.735-742
• /
• 2006

In this paper, we explain the operation scheme and fixed-point design method of DFE (Digital Front End), which performs DC offset compensation, automatic frequency control, and automatic gain control over the input signal to the UE (User Equipment) receiver of IEEE 802.16e OFDMA-TDD system. Then, we analyze the performance of DFE under ITU-R M. 1225 Veh-A 60km/h channel environment. To optimize the fixed-point design of DFE, we reduce the number of bit resulted from calculation without performance degradation, leading to the decreased complexity of the operation in H/W, and design the Loop filter with considering trade-off between the Acquisition time and the Stability.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.6
• /
• pp.510-516
• /
• 2007

The proposed method offers an improved control method for high power density AC/DC adapter by using more energy efficient electrical equipments. Power factor correction (PFC) topology is based on boost topology with boundary conduction mode (BCM). DC/DC topology is based on half-bridge topology with fixed 50% duty and newly introduced off-time control method, which helps to reduce size of the semiconductor and the magnetic devices. Test results with 85W AC/DC adapter (18.5V/4.6A) design show that the measured efficiency is 90% with power density of $36W/in^3$. It also shows low no load power consumption of about 0.5W.

• Korean Journal of Optics and Photonics
• /
• v.10 no.5
• /
• pp.405-412
• /
• 1999

We propose an effective algorithm, which can predict the detailed behavior of the intensity-modulated high speed optical signal after propagating through an optical fiber. The alogrithm is based on the SSF (Split Step Fourier) Method, however, the step size is automatically calibrated in each calculation step to reduce the number of calculations within given round-off error bound. Applying the algorithm to the 2.5 Gbps 100 km transmission and 10 Gbps 40 km transmission simulations, we achieved the calculation time reduction by maximum 1/120 and 1/56 of the calculation time by using the SSF fixed step algorithm previously known. The root-mean-square of the round-off error was kept within -30 dB compared to the signal level throughout the calculation.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.4
• /
• pp.24-32
• /
• 2009

For a design of on/off solenoid actuator for valve actuating, designer must have the experimental knowledge as well as general electromagnetic formulas to design object. It is possible for theoretical knowledge to do the out-line design, but it is impossible to optimal design without experimental knowledge which only can be achieved through many repeated experiments. In addition, in present on/off type solenoid actuator field, the smaller, lightening, lower consumption power, high response time are effected as the most important design factor. So, experimental knowledge is more needed for optimal design of solenoid actuator. In this study, we derived the governing equations for optimal design of on/off solenoid actuator for valve actuating and developed a design program composed electromagnetic theories and experimental parameter values for inexperienced designers. And we proved the propriety of this program by experiments.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.438-440
• /
• 2004

Energy consumption has become an increasingly important consideration in designing real-time embedded systems. In this paper, we propose a voltage scaling method to reduce energy consumption in fixed priority real-time systems using variable voltage processors. The Hyperperiod of tasks is divided into dimains. The most suitable voltage of each domain is determined off-line and stored in a table. During task execution, the voltage of processor is adjusted according to the information of the table. A simulation result shows that the proposed method can reduce 80% of power consumption in comparison to no power management. The difference to the optimal EDF based method is only 5%.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.7
• /
• pp.283-292
• /
• 2013

In order to ensure high performance, all the servers in an existing server cluster are always On regardless of number of real-time requests. They ensure QoS, but waste server power if some of them are idle. To save energy consumed by servers, the server power mode control was developed by shutdowning a server when a server is not needed. There are two types of server power mode control depending on when a server is actually turned off if the server is selected to be off: static or dynamic. In a static mode, the server power is actually turned off after a fixed time delay from the time of the server selection. In a dynamic mode, server power is actually turned off if all the services served in the server are done. This corresponds to a turn off after a variable time delay. The static mdoe has disadvantages. It takes much time to find an optimal shutdown time manually through repeated experiments. In this paper, we propose a dynamic shutdown method to overcome the disadvantages of static shutdown. The proposed method allows to guarantee user QoS with good power-saving because it automatically approaches an optimal shutdown time. We performed experiments using 30 PCs cluster. Experimental results show that the proposed dynamic shutdown method is almost same as the best static shutdown in terms of power saving, but better than the best static shutdown in terms of QoS.

• Journal of the Korean Statistical Society
• /
• v.28 no.4
• /
• pp.523-533
• /
• 1999

We consider the M/G/1 queueing model with D-policy. The server is turned off at the end of each busy period and is activated again only when the sum of the service times of all waiting customers exceeds a fixed value D. We obtain the distribution of unfinished work and show that the unfinished work decomposes into two random variables, one of which is the unfinished work of ordinary M/G/1 queue. We also derive the distribution of queue waiting time.

• Proceedings of the Korean Institute of Interior Design Conference
• /
• 2004.05a
• /
• pp.127-130
• /
• 2004

In order to verify the validity of the exhibition moethod in a science museum, this study undertakes a visitor follow-up survey, and clarifies the influence an exhibition method affect visitor's behavior, and its feature. The tracking research performed the visitor follow-up survey to family company children. The characteristic of the visitor's behavior by the exhibition method; Use frequency becomes low in order of 'Experience type' 'Participation type' 'Fixed type'. Experience type has tendencies, such as repetitive and continuing use, and use time was long. Otherwise use time of Fixed type was short. As a result, although the use frequency of Hands-on is high and its use time is longer than Hands-off, it turns out that is influenced according to factors, such as the exhibition method, presentation and the contents of exhibition.