• 한국인쇄학회지
• /
• 제28권1호
• /
• pp.43-50
• /
• 2010

The 200mesh screen was tensioned and fixed on a frame. When applied tension to 5N and 10N per unit area, a side length of opening of the screen was 163.223${\mu}m$ and 168.224${\mu}m$, respective. But side length not tensioned was 158.879${\mu}m$. We knew that a side length of opening of the screen rarely changes with tension applied to the screen. The appearances that a side length of opening of the screen expand little are due to a decreasing diameter of thread by means of tension. In a thickness measurement of screen, While the high density mesh screen that had a lot of knots that crossed a line of latitude and longitude per unit area appeared a higher numerical value, the low density mesh screen that had a few knots appeared a low numerical value.

• 전기학회논문지
• /
• 제61권10호
• /
• pp.1561-1564
• /
• 2012

In this work, we have fabricated the nanocrystalline carbon films by using unbalanced magnetron sputtering method with graphite and Ti targets for contact strip application of electrical railway. The power density of graphite target was fixed and the power density was increased for the increase of Ti concentration in TiC films. We investigated the hardness, surface roughness, contact angle, resistivity, HRTEM and XPS of TiC films with Ti concentration. The hardness and resistivity were improved with increasing Ti concentration. These results indicate that the improvement of hardness and resistivity is related to the increase of sp2 clusters in TiC films.

• Communications for Statistical Applications and Methods
• /
• 제16권4호
• /
• pp.587-594
• /
• 2009

이 논문에서는 선형회귀모형의 오차항에 대한 변화점 검정 문제를 다룬다. 고정 혹은 변동 모형의 독립 변수와 약한 종속성을 가지는 오차항을 가정하는 관계로 통상적인 중회귀모형뿐만 아니라 ARMA 등의 시계열 모형까지 본 논문에서 포괄한다고 하겠다. 오차항의 분포 변화를 검정하기 위하여 회귀모형의 잔차에 기초한 확률밀도함수 추정값을 이용한다. 적절한 가정하에서 잔차를 이용한 검정이 실제 오차를 이용한 경우와 동일한 극한 분포를 가짐을 보였다.

• 한국통신학회논문지
• /
• 제36권6C호
• /
• pp.384-390
• /
• 2011

The paper derives formulas for the mean-squared error distortion and resulting signal-to-noise (SNR) ratio of a fixed-rate scalar quantizer designed optimally in the minimum mean-squared error sense for a Gaussian density with the standard deviation ${\sigma}_q$ when it is mismatched to a Laplacian density with the standard deviation ${\sigma}_q$. The SNR formulas, based on the key parameter and Bennett's integral, are found accurate for a wide range of $p\({\equiv}\frac{\sigma_p}{\sigma_q}\){\geqq}0.25$. Also an upper bound to the SNR is derived, which becomes tighter with increasing rate R and indicates that the SNR behaves asymptotically as $\frac{20\sqrt{3{\ln}2}}{{\rho}{\ln}10}\;{\sqrt{R}}$ dB.

• 한국세라믹학회지
• /
• 제24권2호
• /
• pp.117-122
• /
• 1987

Glass forming ranges in the AlF3-(Mg＋Sr＋Ba)F2-P2O5 system are studied and ultraviolet transmission, infrared transmission, coefficient of refractive index, thermal expansion coefficient, density and chemical durability of the glasses are determined. Glass forming range is restricted MgF2 0-10wt%, SrF2 10-50wt%, BaF2 10-40wt% in this system. While BaF2 is substituted by SrF2, density and refractive index are decreased, micro hardness and thermal expansion coefficient are increased according to the increasing of SrF2 at fixed MgF2 contents. These samples represent high transmittance(93%) from 400nm to 3800nm and chemical durability of these samples show less than 0.3mg/$\textrm{cm}^2$$.$hy by weightloss.

• Journal of Astronomy and Space Sciences
• /
• 제5권2호
• /
• pp.81-96
• /
• 1988

We have made new models for mass-losing OH/IR stars to explain the properties of the dust shells around them using more accurate information about the material in the shell and the physical precesses including pulsations. We have applied our dust opacity which has been deduced from observations and experimental data to various density distributions, calculated the model emergent spectra, and compared with observations. Contrary to previous suggestions, we could fit observations fairly well using density distribution $\rho\propto r^{-2}$, which is physically plausible, with proper choice of opacities. The time scales for dust formation, growth, and movement are calculated to be compared with pulsation periods. The change of the emergent spectrum depending on the phase of pulsation can be explained fairly well by changing dust condensation radius(for fixed dust condensation temperature) in step with the change in stellar luminosity. The effects of stellar wind models and pulsation models on dust shells with attention to emergent spectra are discussed.

• 전기의세계
• /
• 제25권2호
• /
• pp.100-106
• /
• 1976

A comparative study on thermal, static mechanical and dielectric characteristics were made over a temperature range of ca.20.deg.C to 320.deg.C and a frequency range of KHZ to MHZ band on low density polyethylene specimens crosslinked, respectively, by radiation and chemical method. The thermal property of both specimens shows that softening point appears to unchange by crosslinking, however, melting and liquidizing temperatures attain rapid increase at the imitiation of crosslinking. Mechanical properties show little difference to both specimens crosslinked by different method, further the behaviors were discussed in connection with the relaxation of molecular segments in amorphous phase. Dose dependent dielectric characteristics observed at ambient temperature under several fixed frequencies exhibit extremities at ca. 20 Mrad and the behaviors also were interpreted qualitatively by taking into consideration of dipole concentration change in amorphous phase together with the role of specimen geometry to the depth of oxidative layer. Observing frequency dependent dielectric characteristics, it was also proved that ionic conduction loss is appreciably greater in the specimen prepared by chemical method than that by radiation.

• Journal of Magnetics
• /
• 제22권1호
• /
• pp.65-68
• /
• 2017

This paper reports simulation and evaluation of the magnetic flux density (MFD) of a rotating Halbach magnet (RHM) composed of a rotating inner Halbach cylinder (HC) and a fixed outer HC. We first chose the dimension of a single HC, then determined the dimensions of an inner and outer HC to get MFD = 2 T. Simulation results were used to guide fabrication of an RHM; its magnetic field in the central axis direction agreed well with simulated values.

• 반도체디스플레이기술학회지
• /
• 제12권3호
• /
• pp.7-12
• /
• 2013

Ni-CNT(Carbon Nanotube) composite coatings is were formed by electrodeposition and their physical properties were investigated with variations of CNT content(1, 3, 6. 9 g/L) in the electrolyte solution, while the current density and electroplating time were fixed respectively at $6A/dm^2$ and 90 min.. With increasing CNT content from 1 to 9 g/L, incorporated CNTs into the composite coating were limited from 4.65 wt.% to 7.38 wt.%. Microhardness and contact angle values were increased with increasing CNT content of upto 3 g/L. With increasing the CNT content further, physical properties were degraded due to agglomeration, poor adhesion of CNTs to Ni matrix and thus rough surfaces. Optimum electroplating conditions were found to be the CNT content of 3 g/L, current density of 6 A/dm2 and electroplating time of 90 min.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권9호
• /
• pp.523-526
• /
• 2000

A dual gate trench emitter IGBT structure is proposed and studied numerically using the device simulator MEDICI. The on-state forward voltage drop latch-up current density turn-off time and breakdown voltage of the proposed structure are compared with those of the conventional DMOS-IGBT and trench gate IGBT structures. The proposed structure forms an additional channel and increases collector current level resulting in reduction of on -state forward voltage drop. In addition the trench emitter increases latch-up current density by 148% in comparison with that for the conventional DMOS-IGBT and by 83% compared with that for the trench gate IGBT without degradation in breakdown voltage when the half trench gate width(Tgw) and trench emitter depth(Ted) are fixed at $1.5\mum\; and\; 2\mum$, respectively