• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.8
• /
• pp.639-648
• /
• 2013

This paper describes on the NOx/CO emission characteristics, temperature characteristics and flame structures when firing coal derived synthetic gas especially for gases of Buggenum and Taean IGCC. These combustion characteristics were observed by conducting ambient-pressure elevated-temperature combustion tests in GE7EA model combustor when varying heat input and nitrogen dilution ratio. Nitrogen addition caused decrement in adiabatic flame temperature, thus resulting in the NOx reduction. At low heat input condition, nitrogen dilution raised the CO emission dramatically due to incomplete combustion. These NOx reduction and CO arising phenomena were observed at certain flame temperature of $1500^{\circ}C$ and $1250^{\circ}C$, respectively. As increasing nitrogen dilution, adiabatic flame temperature and combustor liner temperature were decreased and singular points were detected due to change in flame structure such as flame lifting. From the results, the effect of nitrogen dilution on the NOx/CO and flame structure was examined, and the test data will be utilized as a reference to achieve optimal operating condition of the Taean IGCC demonstration plant.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.9
• /
• pp.190-199
• /
• 2014

In this paper, the vestibular hair bundle feature model and integrated vestibular hair cell model were proposed. In conventional modeling studies of vestibular system, only partial mechanisms were modeled, such as the characteristics of the vestibular hair bundles without external forces or the action potential of synapse, and the study about action potential of vestibular afferent considering the characteristics of the vestibular hair bundle was not performed. The proposed integrated vestibular hair cell model reflects external forces considering negative stiffness features of each hair bundles with different regularities of hair cells and our model was compared with conventional model without external forces. As a result, irregular afferent and intermediate afferent with high ratio of firing frequency variations to the changes of external stimulation had small width of negative stiffness section, but the width of the negative stiffness of regular afferent with low ratio was similar to that of conventional negative stiffness features. And the proposed integrated vestibular hair cell model showed almost same results with conventional data with animal experiments in 11 chosen frequency bands. It is verified that our proposed hair bundle feature model is adequately modeled.

• Korean Journal of Applied Biomechanics
• /
• v.27 no.2
• /
• pp.117-124
• /
• 2017

Objective: The purpose of this study was to examine the effect of changes in degrees of freedom of the fingers (i.e., the number of the fingers involved in tasks) on the task performance during force production and releasing task. Method: Eight right-handed young men (age: $29.63{\pm}3.02yr$, height: $1.73{\pm}0.04m$, weight: $70.25{\pm}9.05kg$) participated in this study. The subjects were required to press the transducers with three combinations of fingers, including the index-middle (IM), index-middle-ring (IMR), and index-middle-ring-little (IMRL). During the trials, they were instructed to maintain a steady-state level of both normal and tangential forces within the first 5 sec. After the first 5 sec, the subjects were instructed to release the fingers on the transducers as quickly as possible at a self-selected manner within the next 5 sec, resulting in zero force at the end. Customized MATLAB codes (MathWorks Inc., Natick, MA, USA) were written for data analysis. The following variables were quantified: 1) finger force sharing pattern, 2) root mean square error (RMSE) of force to the target force in three axes at the aiming phase, 3) the time duration of the release phase (release time), and 4) the accuracy and precision indexes of the virtual firing position. Results: The RMSE was decreased with the number of fingers increased in both normal and tangential forces at the steady-state phase. The precision index was smaller (more precise) in the IMR condition than in the IM condition, while no significant difference in the accuracy index was observed between the conditions. In addition, no significant difference in release time was found between the conditions. Conclusion: The study provides evidence that the increased number of fingers resulted in better error compensation at the aiming phase and performed a more constant shooting (i.e., smaller precision index). However, the increased number of fingers did not affect the release time, which may influence the consistency of terminal performance. Thus, the number of fingers led to positive results for the current task.

• Archives of design research
• /
• v.21
• /
• pp.99-106
• /
• 1997

There were the changes of shapes and color tones when the soil materials e.g. Blue-Porcelain, White-Porcelain, Bunchong, mixed A and B, mullite, Sanchong and Ongki - used by most domestic ceramic artists - were glazed at $ 950^{\circ}C,; 1200^{\circ}C,; 1250^{\circ}C,; 1280^{\circ}C,;1300^{\circ}C$ After the materials were dried out at 120t: in an electric oven, they were mixed with water, keeping the percentage of moisture content 25% and kneaded specimens which are hexahedron by $$ 250{\times}30{\times}8mm$$were produced and dried after calibrated at 200mm interval with a vernier caliper. After the materials were dried and glazed, they showed few shape-changes at $950^{\circ}C$ but began to changed at $1200^{\circ}C$,especially Bunchong and Ongki made rapid changes. In the case of color-change, White-Porcelain changed very little. The color of Blue-Porcelain, mixed A and B, Sanchong, Mullite changed to ]aune brilliant as temperature went up but Bunchong and Ongki changed to dark brown or dark chocolate under the same conditions. This study aims at suggestion of the basic data which minimize failure rates by recognizing the property of the materials on the basis of this study and regulating shape-change phenomena and sensitive changes of color when ceramic artists work.

• The Journal of the Acoustical Society of Korea
• /
• v.21 no.5
• /
• pp.430-437
• /
• 2002

Having a variety of good characteristics against other pattern recognition techniques, the multilayer perceptron (MLP) has been widely used in speech recognition and speaker recognition. But, it is known that the error backpropagation (EBP) algorithm that MLP uses in learning has the defect that requires restricts long learning time, and it restricts severely the applications like speaker recognition and speaker adaptation requiring real time processing. Because the learning data for pattern recognition contain high redundancy, in order to increase the learning speed it is very effective to use the online-based learning methods, which update the weight vector of the MLP by the pattern. A typical online EBP algorithm applies the fixed learning rate for each update of the weight vector. Though a large amount of speedup with the online EBP can be obtained by choosing the appropriate fixed rate, firing the rate leads to the problem that the algorithm cannot respond effectively to different learning phases as the phases change and the number of patterns contributing to learning decreases. To solve this problem, this paper proposes a Changing rate and Omitting patterns in Instant Learning (COIL) method to apply the variable rate and the only patterns necessary to the learning phase when the phases come to change. In this paper, experimentations are conducted for speaker verification and speech recognition, and results are presented to verify the performance of the COIL.

• Journal of the Korean Ceramic Society
• /
• v.20 no.2
• /
• pp.135-146
• /
• 1983

This study is to investigate the properties of domestic fly ash for utilization as data in regard to fly ash which is by-product of domestic coal powder plants and the possibility of utilization as insulation material of domestic fly ash. Composition refractoriness size distribution density contents of hollow particles and crystalline phase were examined as the properties of domestic fly ash. As to the fired test pieces of fly ash by itself that varied contents of hollow particles with four kinds and of the fly ash-clay-saw dust system linear shrinkage bulk density app. porosity compressive strength thermal conductivity and structures were investigated for the possibility of utilization as an insulation material. The results are as follows : 1. The properties of the fly ash I) The constituent particle of the fly ash is spherical and it contains not a few hollow particles (floats by water 0.30-0.50 floats by $ZnCl_2$ aq.(SpG=1.71) 6.97-16.72%). ii) The chemical compositions of fly ash are $SiO_243.9-54.1%$ , $Al_2O_321.0-30.7%$ Ig loss is 7.4-24.1% and the principal of Ig loss is unburned carbon. iii) Fly ash was not suitable to use for mortar and concrete mixture because Ig. loss value is higher than 5% 2. Utilization as insulation material I) The test pieces of original fly ash floats by water floats by ZnCl2 aq(SpG=1.71) p, p t by ZnCl2 aq.(SpG=1.71) that were fired at 110$0^{\circ}C$ represented 0.11-0.18 kcal/mh$^{\circ}$ C as thermal conductivity value. ii) The test pieces which (76.5-85.5) wt% fly ash-(8.5, 9.5) wt% clay-(5.0-15.0) wt% saw dust system(68.0-72.0) wt% fly ash -(17.0-18.0)wt% clay-(10.0-15.0) wt% saw dust system and 59.5 wt% fly ash-25.5 wt% clay-15.0wt% saw dust system were fired at 110$0^{\circ}C$ the thermal conductivity was less than 0.1Kcal/mh$^{\circ}$ C. iii) In view of thermal conductivity and economic aspect insulation materials which added saw dust as blowing agent and clay as inorganic binder are better than that of fly ash as it is or separated hollow fly ash particles. iv) When the saw dust contents increased in the (59.5-90.0) wt% saw dust system and when amount of clay de-creased and firing temperature decreased under the condition of equal addition of saw dust app. porosity increased but bulk density compressive strength and thermal conductivity decreased.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.2
• /
• pp.468-474
• /
• 2017

A test service for the weapon systems evaluation is one of the most important processes during the weapon systems acquisition or development life cycle. Before completion of weapon systems development, the appropriate evaluation test can reduce risk and expense which might be expected during weapon systems development procedure. In this paper, it is suggested that a probabilistic prediction method based on Monte Carlo simulation for how much the annual weapon systems evaluation test excution ratio can be reached compared to the yearly initial planned test quantity. And then a weapon systems evaluation test quantitative management scheme is suggested to assist decision making for the test schedule manager who can arrange monthly test schedule based on the prediction result of annual test excution ratio. And the proposed method is applied for the weapon systems evaluation firing test data of the 8th directorate, Agency for Defense Development(ADD). And also the application result is examined.

• Korean Journal of Remote Sensing
• /
• v.37 no.3
• /
• pp.395-408
• /
• 2021

In this study, we investigated the effects of wind speed and direction on building fires using GIS and a CFD model. We conducted numerical simulations for a fire event that occurred at an apartment in Ulsan on October 8, 2020. For realistic simulations, we used the profiles of wind speeds and directions and temperatures predicted by the local data assimilation and prediction system (LDAPS). First, using the realistic boundary conditions, we conducted two numerical simulations (a control run, CNTL, considered the building fire and the other assumed the same conditions as CNTL except for the building fire). Then, we conducted the additional four simulations with the same conditions as CNTL except for the inflow wind speeds and direction. When the ignition point was located on the windward of the building, strong updraft induced by the fire had a wide impact on the building roof and downwind region. The evacuation floor (15th floor) played a role to spread fire to the downwind wall of the building. The weaker the wind speed, the narrower fire spread around the ignition point, but the higher the flame above the building reaches. When the ignition point was located on the downwind wall of the building, the flame didn't spread to the upwind wall of the building. The results showed that wind speed and direction were important for the flow and temperature (or flame) distribution around a firing building.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.19 no.1
• /
• pp.75-91
• /
• 2024

Recently, global business environment is changing dramatically along with the acceleration of technological innovation amid the war, climatic change, and geopolitical instability. Accordingly, it is difficult to predict or plan for the future as the volatility, complexity, ambiguity, and uncertainty of the industrial ecosystem continue to increase. Therefore, organizations are undergoing inevitable restructuring in accordance with their survival strategy, for instance, removing marginal businesses or firing. Accordingly, office workers are seeking a startup as an alternative for their continuous economic activity amid rising anxiety factors that make them think they would lose their jobs unintentionally. Here, this study is aimed to verify through what paths office workers' self-determination influences the process of converting to a startup. For this study, an online survey was carried out, and 310 respondents' valid data were analyzed through SPSS and AMOS. To sum up the results, first, office workers' self-determination did not have significant effects on entrepreneurial intention. However, it was confirmed that self-determination had positive (+) effects on innovativeness and perception of the startup support system. This result shows that their psychology works to prepare step by step by accumulating innovative experiences and increasing perception of the startup support system from a long-term life path perspective rather than challenging startups right way. Second, innovativeness is found to have positive (+) effects on entrepreneurial intention. Also, perception of the startup support system had positive (+) effects on entrepreneurial intention. This implies that when considering startups, they are highly aware of the government's various startup support systems. Third, innovativeness is found to have positive (+) effects on perception of the startup support system. It is judged that perception of the startup support system is valid for prospective founders to exhibit their innovativeness and realize new ideas. Fourth, it was confirmed that innovativeness and perception of the startup support system mediated correlation between self-determination and entrepreneurial intention, and perception of the startup support system mediated correlation between innovativeness and entrepreneurial intention, which shows that it is a crucial factor in entrepreneurial intention. Although previous studies related to startups deal with students mostly, this study targets office workers who form a great part in economic activities, which makes it academically valuable in terms of being differentiated from others and extending the scope of research. Also, when we consider the fact that the motivation for self-determination alone fails to stimulate entrepreneurial intention and the complete mediation of innovativeness and the startup support system, it has great implications in practical aspects such as the government's human and material support systems. In the selection and analysis of samples, this study exhibits a limitation that the problem of common method bias is not completely resolved. Also, additional definitive research is needed on whether entrepreneurial intention is formed and converted into startup behavior. Academically and practically, this study deals with the relationship between humans' psychological motives and startups which has not been handled sufficiently in previous studies. The conversion of office workers to startups is expected to have effects on individuals' economic stability and the state's job creation; therefore, it needs to be investigated continuously for its great value.