• Journal of Korean Port Research
• /
• v.13 no.1
• /
• pp.175-182
• /
• 1999

The ocean wave is hydrodynamically investigated to get more reliable solution. To improve the computational accuracy more fine grids are used with relatively less computer storage on the free surface. One element of the free surface is discretized into more fine grids because the free-surface waves are much affected by the grid size in the finite difference scheme. Here the multi-grid method is applied to confirm the efficiency for the S103 ship model by solving the Navier-Stokes equation for the turbulent flows. According to the computational result approximately 30% can be improved in the free surface generation, Finally the limiting streamlines show numerical result is similar to the experiment by twin tuft.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.3 s.168
• /
• pp.93-100
• /
• 2005

The top and bottom nozzles of PWR fuel assembly are connected by guide thimbles and an instrumentation tube that are connected with spacer grids. The fuel rods are inserted into the each cell of spacer grids. The loads acting on the fuel assembly are transmitted to the guide thimbles through the flow plate of top nozzle The axial loads applied to the fuel assembly are not equally distributed among the guide thimble due to the geometry of the top nozzle flow plate and spacer grid. In this study, the load concentration factors for the $17\times17$ fuel assembly were calculated. The analytical model fur the calculation of the load concentration factor of top nozzle flow plate was developed using ANSYS 5.6. The finite element analyses were performed using the model composed of top nozzle, guide thimble, and spacer grid. And, the analysis results were compared with the test results.

• Journal of Korean Port Research
• /
• v.11 no.1
• /
• pp.121-128
• /
• 1997

To analyze the ocean wave more efficiently, more fine grids are used with relatively less computer memory. Each element of free surface is discretized into more fine grids because the ocean waves are much influenced by the mesh used in the finite difference scheme. According to the flow analysis, remarkable improvements could be seen in the free surface generation. The multi grid is applied to confirm the validity of scheme. The Baldwin Lomax turbulence model is used for the analysis of S103 Inuid ship. Finally some discussion on experiments was made for the physical phenomena of the viscous

• Wind and Structures
• /
• v.8 no.6
• /
• pp.407-426
• /
• 2005

A hybrid RANS/LES approach, based on the Limited Numerical Scales concept, is applied to the numerical simulation of the flow around a square cylinder. The key feature of this approach is a blending between two eddy-viscosities, one given by the $k-{\varepsilon}$ RANS model and the other by the Smagorinsky LES closure. A mixed finite-element/finite-volume formulation is used for the numerical discretization on unstructured grids. The results obtained with the hybrid approach are compared with those given by RANS and LES simulations for three different grid resolutions; comparisons with experimental data and numerical results in the literature are also provided. It is shown that, if the grid resolution is adequate for LES, the hybrid model recovers the LES accuracy. For coarser grid resolutions, the blending criterion appears to be effective to improve the accuracy of the results with respect to both LES and RANS simulations.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.939-944
• /
• 2003

The analysis involves an adaptive grid that is created under a criterion of element categorization of filling states and locations in the total region at each time step. By using an adaptive grid wherein the elements, finer than those in internal and external regions, are distributed at the surface region through refinement and coarsening procedures, a more efficient analysis of transient fluid flow with free surface is achieved. Using the proposed numerical technique, the collapse of a dam is analyzed. The numerical results agree well with the theoretical solutions as well as with the experimental results. Through comparisons with the numerical results of several cases using different types of grids, the efficiency of the proposed technique is verified.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.06a
• /
• pp.1-11
• /
• 2001

This Paper presents the result of a parametric study on the behavior of stiffened grid reinforced segmental wall resting on non-yielding foundation. The parametric study was conducted using the nonlinear finite element analysis. In the finite element analysis, the step by step construction of the wall such as backfill, block reinforcement, block/backfill and soil/reinforcement interfaces were carefully modeled. The mechanical behavior of stiffened grid reinforced segmental walls was then investigated based on the result of analysis with emphasis on the effect of reinforcement stiffness on the behavior of the wall. The results of analysis indicate that the horizontal wall displacement decrease; with increasing the reinforcement stiffness at a decreasing rate, and that the horizontal stress at the back of the reinforced soil block does not much vary with the reinforcement stiffness. It is also revealed that the calculated maximum vertical stress at the base of the reinforced soil block agrees well with that based on the Meyerhof distribution and that the reinforcement and the connection force are considerably smaller than what might be expected based on the current design assumptions. The implications of the findings from this study to current design approaches were discussed in detail.

• Transactions of Materials Processing
• /
• v.14 no.6 s.78
• /
• pp.514-519
• /
• 2005

A tube hydroformability testing system was designed and fabricated enabling to apply the forming condition along arbitrarily pre-programmed internal pressure-axial feed path. The free-bulging and T-forming tests were carried out on the extruded aluminum (A6063) tube specimens with 40.6 mm outer diameter and 2.25 mm thickness. Nine different combinations of internal pressure and axial feed, yielding different strain paths from one another, were taken into consideration in order to induce bursting at various deformation modes. Major and minor strains were automatically measured from deformed grids around the fracture using a stereo-vision-based surface strain measurement system, named ASIAS. The forming limit diagram of the A6063 tube material was successfully obtained. Most of the data points acquired from free bulging and T-forming tests appeared in the range of negative minor strain on the FLD and are mostly located near the strain paths calculated from explicit finite element simulations. The forming limit obtained from tests after pre-tension was considerably lower than that from tests without pre-tension, which showed the strain path-dependency of the forming limit as well known in the sheet forming fold.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.1
• /
• pp.86-91
• /
• 2008

An integrated multidisciplinary analysis and design system plays a critical role in the preliminary design of an aircraft. In this work a system based on the CATIA is developed for multidisciplinary computational design; aerodynamics, elasticity, and radar frequency stealth. Common data base of geometry and rectangular grids is generated and used for aerodynamic and structural analysis, while derivative triangular grids are generated for the RCS calculation. The panel method (PANAIR), FEM (NASTRAN), and PO technique are used for aerodynamic, structural, and RF stealth computations, respectively, and several additional algorithms are developed for the effective communication of the common data.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.905-910
• /
• 2003

One of the methods that are used to compare and verify the supporting performance of the spacer grids developed is the vibration characteristic test. A modal test in this paper is performed for a dummy rod 3,847mm tall supported by eight New Doublet (ND) spacer grids. For the vibration test in air, nine accelerometers, one displacement sensor and one shaker are used for acquiring signals, and an I-DEAS TDAS software is employed for analyzing the signals. Also, a finite element (FE) analysis is performed by a beam-spring simple model and a contact model simulating the contact phenomenon between the rod and the fm spring. And then, the result of the FE analysis is compared with that of the modal test. The natural frequencies as well as the mode shapes calculated by the proposed contact models have a greater similarity to the test results than those by the previous beam-spring model. In addition, for grasping whether or not the modal parameters are influenced by where shaking spot is, two kinds of tests are performed; one is for the shaker attached at the fourth span (center), the other is for the shaker at the fifth span that is one span nearer to the bottom of the rod. The latter shows higher MAC than the former. Finally, the vibration displacements are measured in the range of 0.112-0.214mm for the excitation force of 0.25-0.75 N.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.15 no.3
• /
• pp.190-195
• /
• 2003

For many coastal problems, such as wave transformation, tidal circulation, sediment transports and diffusion phenomena, we resort to numerical techniques. The representative numerical techniques are the method of finite differences and finite elements. The approximate algebraic equations, referred to as finite difference equations(FDEs), are subsequently solved at discrete grid points within the domain of interests. Therefore, a set of grid points within the domain, as well as the boundaries of the domain, must be specified. The generation of grids for FDEs, with uniform spacing, is very simple compared to that of finite elements. However, within a very complex domain, there are few grid generation tools we can use conveniently. Unfortunately, most of the commercial grid generation programs are developed only for finite element method. In this paper, grid generation method using digitizer, with uniform rectangular spacing, are introduced in detail. Didger and Surfer programs by Golden Software are necessary to produce comparatively accurate and simple depth data.