• Structural Engineering and Mechanics
• /
• 제77권1호
• /
• pp.103-114
• /
• 2021

Ultra high strength concrete (UHSC) originally proposed by Richards and Cheyrezy (1995) composed of cement, silica fume, quartz sand, quartz powder, steel fibers, superplasticizer etc. Later, other ingredients such as fly ash, GGBS, metakaoline, copper slag, fine aggregate of different sizes have been added to original UHSC. In the present investigation, the combined effect of coarse aggregate (6mm - 10mm) and steel fibers (0.50%, 1.0% and 1.5%) has been studied on UHSC mixes to evaluate mechanical and fracture properties. Compressive strength, split tensile strength and modulus of elasticity were determined for the three UHSC mixes. Size dependent fracture energy was evaluated by using RILEM work of fracture and size independent fracture energy was evaluated by using (i) RILEM work of fracture with tail correction to load - deflection plot (ii) boundary effect method. The constitutive relationship between the residual stress carrying capacity (σ) and the corresponding crack opening (w) has been constructed in an inverse manner based on the concept of a non-linear hinge from the load-crack mouth opening plots of notched three-point bend beams. It was found that (i) the size independent fracture energy obtained by using above two approaches yielded similar value and (ii) tensile stress increases with the increase of % of fibers. These two fracture properties will be very much useful for the analysis of cracked concrete structural components.

• Computers and Concrete
• /
• 제30권4호
• /
• pp.257-267
• /
• 2022

Two different types of rubber aggregates (40 mesh rubber powder and 1-4 mm rubber particles respectively) were devised to substitute fine aggregates at 10%, 15%, 20% and 30% by volume in self-compacting concrete to investigate their basic mechanical properties. The results show that with the increase of rubber content, the reduction of compressive strength, splitting tensile strength and static modulus of elasticity gradually increase, and energy dissipation performance gradually increase. The rubber addition significantly reduces brittleness and decelerates damaged process. Whilst, the effect of rubber particles is greater when they are finer. Considering the mechanical properties, the optimal rubber content is 10%. It is recommended that the rubber volume content in rubberized concrete (RC) should not be higher than 20%. In addition, a constitutive model under uniaxial compression was proposed basing on the strain equivalent principle of Lemaitre and the damage theory, which was in good agreement with the test curves.

• Computers and Concrete
• /
• 제29권 5호
• /
• pp.335-346
• /
• 2022

Geopolymers are an important alternative material supporting recycling, sustainability, and waste management. Durability properties are among the most critical parameters to be investigated; in this study, the durability of manufactured geopolymer samples under the attack of 10% magnesium sulfate and 10% sodium sulfate solution was investigated. 180 cycles of freezing and thawing were also tested. The experimentally obtained results investigate the durability of geopolymer mortar prepared with fly ash (class F) and alkali activator. Three different quarry dust wastes replaced the river sand aggregate: limestone, marble, and basalt powder as fine filler aggregate in three different replacement ratios of 25%, 50%, and 75% to produce ten series of geopolymer composites. The geopolymer samples' visual appearance, weight changes, UPV, and strength properties were studied for up to 12 months at different time intervals of exposure to sulfate solutions to investigate sulfate resistance. In addition, Scanning Electron Microscopy (SEM), EDS, and XRD were used to study the microstructure of the samples. It was beneficial to include quarry waste as a filler aggregate in durability and mechanical properties. The compact matrix was demonstrated by microstructural analysis of the manufactured specimens. The geopolymer mortars immersed in sodium sulfate showed less strength reduction and deterioration than magnesium sulfate, indicating that magnesium sulfate is more aggressive than sodium sulfate. Therefore, it is concluded that using waste dust interrogation with partial replacement of river sand with fly ash-based geopolymers has satisfactory results in terms of durability properties of freeze-thaw and sulfate resistance.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.237-238
• /
• 2023

When primer is applied manually, adhesion performance decreases due to a decrease in primer penetration performance on the surface, and construction period delay may occur due to a long time due to a decrease in work efficiency when a large area is worked using a conventional roller. In addition, in the case of the roller method, precision work in corners and narrow spaces is not possible, so it is urgent to come up with measures to ensure uniform quality. In addition, secondary work occurs to remove fine powder from the surface before primer application, resulting in construction period delay due to the rise of the working stage. Therefore, in this study, equipment was used instead of manual work for primer work, and as a result, penetration performance and adhesion performance were improved about twice. From these results, it was confirmed that favorable results such as improving work speed, securing high quality, improving the working environment, and resolving the shortage of functional workers can be obtained.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.297-298
• /
• 2023

In the concrete industry, efforts are being made to reduce CO₂ emissions, and technologies that collect, store, and utilize CO₂ have recently been studied. This study analyzed the change in compressive strength after the accelerated carbonation test of Non-Sintered Cement(NSC) mortar. Type C Fly Ash and Type F Fly Ash were mixed in a 1:1 ratio and then mixed with Blast Furnace Slag fine powder to produce NSC. The mortar produced was cured underwater until the target age. In addition, an accelerated carbonation test was conducted under the condition of a concentration of 5 (±1.0%) of CO₂ gas for 14 days. The mortar compressive strength was measured before and after 14 days of accelerated carbonation test based on the 7th and 28th days of age. As a result of the experiment, the compressive strength was improved in all binder. In general, the compressive strength of NSC mortar subjected to the accelerated carbonation test was similar to that of Ordinary Portland Cement(OPC) mortar not subjected to the accelerated carbonation test.

• 대한안전경영과학회지
• /
• 제25권4호
• /
• pp.153-161
• /
• 2023

Carbon black is a material in the form of fine black powder obtained by incomplete combustion or pyrolysis of hydrocarbons, and is composed of 90-99% carbon, and the rest is composed of hydrogen and oxygen. In the event of an emergency during the manufacture of carbon black, the generated tail gas should be safely discharged through an emergency line to prevent fire, explosion, and environmental pollution accidents caused by the tail gas. If the pressure continues to rise, the pressure control valve shall operate and the rupture plate shall be ruptured sequentially and the tail gas shall be discharged to the vent stack through the emergency line. As an emergency emission system, even if some untreated substances in the tail gas are released into the atmosphere, they are lighter than air, so it is safe to discharge them to a safe place through the Vent Stack. If the gas pressure is rising or worse, it is discharged from the Vent Stackine, and discharging fuel.

• Korean Chemical Engineering Research
• /
• 제54권1호
• /
• pp.44-51
• /
• 2016

전도성 물질인 철 입자(iron particles)를 절연체로 코팅하여 제작한 압분자심(powder core)은 비저항이 작기 때문에 고주파 영역에서 와전류 손실이 크다. 이 결함을 해결하기 위해서는 압분자심의 비저항을 증가시킬 필요가 있다. 이 연구에서는 압분자심의 비저항을 증가시키기 위하여 유성볼밀을 사용하여 전기전도성 철 입자에 산화제2구리를 코팅하였다. 반응표면분석법을 사용하여 코팅변수를 최적화하였다. 최적화 시 인자는 CuO 질량분율, 밀 회전 수, 코팅시간, 볼 크기, 볼 질량, 시료 질량이며, 반응변수는 비저항이었다. 6인자-일부요인배치법에 의하면 주된 인자는 CuO 질량분율, 밀 회전 수, 코팅시간이었다. 3-인자 완전요인배치법과 최대경사법을 사용하여 3개 인자의 수준을 선정하였다. 최대경사법을 사용하여 최고의 비저항을 갖는 영역에 접근하였다. 최종적으로 Box-Behnken법을 사용하여 스크린한 인자들의 반응표면을 분석하였다. Box-Behnken법 결과에 의하면 CuO 질량분율과 밀 회전 수가 코팅공정 효율에 영향을 주는 주요 인자이었다. CuO 질량분율이 증가함에 따라 비저항은 증가하였다. 그에 반해서 밀 회전 수가 감소함에 따라 비저항은 증가하였다. 코팅공정을 최적화한 모델로부터 계산한 예측값과 실험값과는 통계적으로 유의하게 일치하였다($Adj-R^2=0.944$). 비저항의 최고값을 갖는 코팅조건은 CuO 질량분율은 0.4, 밀 회전 수는 200 rpm, 코팅시간은 15분이었다. 이 조건에서 코팅한 정제의 비저항 측정값은 $530k{\Omega}{\cdot}cm$이었다.

• Journal of Acupuncture Research
• /
• 제29권6호
• /
• pp.35-45
• /
• 2012

Objectives : This study was designed to investigate Effects of Sujeom powder(SJP) pharmacopuncture Injected at Jung-wan($CV_{12}$) in rats with caerulein-induced acute pancreatitis(AP). Methods : We examined changes of organ weight, histology, immunohistochemistry and gene expression of cycolooxygenase 2(COX-2) in the pancreas. Twenty adult male Sprague-Dawley rats were divided into four groups as follow: normal(Nor), caerulein-induced(Con), caerulein+SJP pharmacopuncture 0.2mL injected at Jung-wan($CV_{12}$)(SA), and caerulein+SJP pharmacopuncture 0.8 mL injected at Jung-wan($CV_{12}$)(SB) groups. Pancreatic tissues of rats from all groups were removed for histological observation and light microscopic examination. Interleukin-6(IL-6) levels were determined spectrophotometrically. Results : The ratio of pancreas/body weights was significantly(p<0.05) increased in the Con, the SA and the SB compared with the Nor, but was slightly decreased in the SA and in the SB groups compared with the Con. Caerulein administration has significantly(p<0.05) increased in the levels of amylase, but the SA, the SB significantly(p<0.05) decreased in the levels of these enzyme. The levels of amylase were increased significantly with caerulein administration, but were inhibited significantly in the SA and in the SB groups. Interleukin-6(IL-6) levels were significantly(p<005) increased in all groups compared with the Nor, especially in the SB. were significantly increased. The levels of Tumor necrosis factor(TNF)-${\alpha}$ levels were significantly increased in all groups compared with the Nor. In the conclusion, the datum of IL-6 and TNF-${\alpha}$ are suggested that the inflamation was still existed actively at a point of measurement(24 hours later). The COX-2 positive materials are observed in the pancreas from the Con, but these positive materials are decreased in the SJP pharmacopuncture at Jung-wan($CV_{12}$) treatment group. Conclusion : SJP pharmacopuncture injected at Jung-wan($CV_{12}$) is potentially capable of limiting pancreatic damage during AP by restoring the fine structure of acinar cells and tissues. Therefore we can say that SJP pharmacopuncture Injected at Jung-wan($CV_{12}$) may have beneficial effects in the treatment of caerulein-induded AP. Further studies about the adequate amount of the SJP pharmacopuncture and about more effective route of administration is still required.

• 콘크리트학회논문집
• /
• 제22권3호
• /
• pp.287-295
• /
• 2010

본 연구에 사용한 시멘트는 보통 포틀랜드 시멘트이며, 공극 최소화를 위한 충전재는 미세석영을 사용하였고 고강도화에 따른 취성파괴 문제를 개선하기위해 강섬유를 사용하여 압축강도 300 MPa 이상의 초고강도 분체콘크리트를 개발 하고자 하였다. 콘크리트의 강도를 크게 향상시키기 위한 연구의 일환으로 계면영역의 부착강도를 향상시킬 수 있는 크기 0.6 mm 이하의 규사, 백운석, 보크사이트, 페로실리콘을 선정한 후 각각의 배합비, 양생조건을 달리하여 압축강도를 비교분석 하였다. 초고강도 분체콘크리트는 보통콘크리트와 달리 사용재료의 영향이 대단히 중요하다. 분체 콘크리트의 압축강도 측정 결과 페로실리콘 > 보크사이트 > 백운석 > 규사 순으로 골재의 강도가 압축강도에 큰 영향을 미치는 경향을 알 수 있었으며 페로실리콘의 경우 시멘트 중량 기준하여 혼입량 110%일 때 가장 큰 강도를 나타내었다. SEM 촬영 결과 C-S-H수화물이 비교적 많이 생성되었고, 고온고압양생으로 토버모라이트와 조놀라이트가 생성된 것을 확인 하였다. 또한 골재의 세립화, 분체의 치밀충전화 및 반응성 재료의 사용으로 인해 페이스트가 고강도화 되고, 강섬유를 사용하여 인성을 보강함으로써, 28일 압축강도 341 MPa의 초고강도 분체콘크리트를 성공적으로 개발 하였다.

• 한국산학기술학회논문지
• /
• 제21권10호
• /
• pp.30-39
• /
• 2020

본 연구에서는 Sol-Gel 방법을 이용하여 단일상의 Barium ferrite 분말을 제조하였으며, 이때 Ba에 대한 Fe(Fe/Ba)의 몰비와 열처리 온도를 달리하여 단일상의 Barium ferrite를 제조하기 위한 최적의 실험조건을 찾고자 하였다. 또한 고밀도 자기기록매체에 사용되기 위한 2.5 ~ 5.5 kOe 크기의 보자력을 가지는 ferrite 미립자 제조를 위해 보자력 제어에 뛰어난 효과를 지닌 cobalt를 첨가제로 하여 cobalt가 치환된 Barium ferrite 미립자를 제조하고 이들에 대한 자기적 특성 변화를 조사하였다. 제조된 Barium ferrite의 결정구조 및 단일상의 합성여부를 확인하기 위해 X-Ray Diffractometer(XRD), Thermogravimetric-Differential Thermal Analysis(TG-DTA), Field Emission Scanning Electron Microscope(FE-SEM)을 이용하여 분석하였으며, 화학적 구조와 조성의 분석을 위해 Fourier Transform Infrared Spectroscopy(FT-IR), Energy Dispersive X-Ray Spectrometer(EDS)를 사용하였다. 또한 Vibrating Sample Magnetometer(VSM)을 통해 cobalt가 치환된 Barium ferrite 분말의 보자력을 측정하였다. 그 결과 단일상의 Barium ferrite는 Fe/Ba의 몰비가 10, 900 ℃의 열처리 온도에서 가장 잘 합성되었다. Co의 첨가량이 증가할수록 보자력은 감소하였으며 Fe에 대한 Co(Co/Fe)의 몰비가 0.16 이내 일 때, 고밀도 자기기록매체에 사용할 수 있는 보자력 값인 2.5 ~ 5.5 kOe를 가지는 Barium ferrite가 합성되었다.